45602 Lamp Module with Dimmer Control

This describes the Z-Wave device 45602, manufactured by ACT - Advanced Control Technologies with the thing type UID of act_45602_00_000.

Lamp Module with Dimmer Control

Channels

The following table summarises the channels available for the 45602 Lamp Module with Dimmer Control.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the 45602 Lamp Module with Dimmer Control. Detailed information on each parameter can be found below.

Parameter Description
5: Ignore Start Level When Receiving Dim Commands  
7: Dim Rate Step Count - ZWave Control Number of steps the dimmer will change when controlling via ZWave
8: Dim Rate Step Duration - ZWave Control Timing of each step the dimmer will change when controlling via ZWave
9: Dim Rate Step Count - Manual Control Number of steps the dimmer will change when controlling manually
10: Dim Rate Step Duration - manual Control Timing of each step the dimmer will change when controlling manually
11: Dim Rate Step Count - ZWave All on/off Number of steps the dimmer will change when receiving a ZWave all on/off command
12: Dim Rate Step Duration - ZWave All on/off Timing of each step the dimmer will change when receiving a ZWave all on/off command
29: Load Sensing Sense when existing switch is used to turn on the lamp

5: Ignore Start Level When Receiving Dim Commands

Overview

Every “Dim” command from your remote controller includes a start level embedded in it. The 45602 can be set to ignore the start level that is part of the dim command. Setting parameter 5 to a value of 0 will cause the 45602 to dim or brighten from the start level embedded in the command

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 1
Options Respect Start Level (0)      
  Ignore Start Level (default) (1)      

7: Dim Rate Step Count - ZWave Control

Number of steps the dimmer will change when controlling via ZWave

Overview

Dim Rate Adjustments: Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 99
Default Value 1

8: Dim Rate Step Duration - ZWave Control

Timing of each step the dimmer will change when controlling via ZWave

Overview

Dim Rate Adjustments: Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 1 to 255
Default Value 3

9: Dim Rate Step Count - Manual Control

Number of steps the dimmer will change when controlling manually

Overview

Dim Rate Adjustments: Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 1 to 99
Default Value 1

10: Dim Rate Step Duration - manual Control

Timing of each step the dimmer will change when controlling manually

Overview

Dim Rate Adjustments: Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 255
Default Value 3

11: Dim Rate Step Count - ZWave All on/off

Number of steps the dimmer will change when receiving a ZWave all on/off command

Overview

Dim Rate Adjustments: Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 99
Default Value 1

12: Dim Rate Step Duration - ZWave All on/off

Timing of each step the dimmer will change when receiving a ZWave all on/off command

Overview

Dim Rate Adjustments: Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 1 to 255
Default Value 3

29: Load Sensing

Sense when existing switch is used to turn on the lamp

Overview

Load sensing allows you to operate the lamp using the existing switch on the lamp by sensing a change in the resistive load of the light plugged in. When it detects the change in resistance it will turn the lamp on to full power.

When replacing a burned-out light bulb, the load sensing feature will automatically turn the light ON when the new bulb is installed even if the Z-wave module was previously turned OFF

Property Value      
Configuration ID config_29_1      
Data Type INTEGER   Default Value 0
Options Disabled (default) (0)      
  Enabled (1)      

Did you spot an error in the above definition or want to improve the content? You can edit the database here.