ZDM230 HomePro Wall Dimmer ZDM230

This describes the Z-Wave device ZDM230, manufactured by ACT - Advanced Control Technologies with the thing type UID of act_zdm230_00_000.

HomePro Wall Dimmer ZDM230

Overview

Radio Frequency (RF) Controlled, 500W, 230 VAC, European Wall Mounted, 3-Way Dimmer Receiver, Dual Switch, Release 1.1

Channels

The following table summarises the channels available for the ZDM230 HomePro Wall Dimmer ZDM230.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the ZDM230 HomePro Wall Dimmer ZDM230. Detailed information on each parameter can be found below.

Parameter Description
1: Ignore Start-Level (Transmitting) Dimmers controlled by this switch will start dimming from their current level.
2: Suspend group 4 Disable transmitting commands to Z-Wave devices that are in Group 4 without disassociating…
3: Night Light n night-light mode the LED on the switch will turn ON when the switch is turned OFF.
1: Group 1 Left paddle
2: Group 2 Right Paddle
3: Group 3 Right double click paddle
4: Group 4 Group used to inform devices about status updates

1: Ignore Start-Level (Transmitting)

Dimmers controlled by this switch will start dimming from their current level.

Overview

Set ignore start level bit when transmitting dim commands. The ZDM230 can send Dim commands to Z-Wave enabled dimmers. The Dim command has a start level embedded in it. A dimmer receiving this command will start dimming from that start level. However, the command also has a bit that indicates whether the dimmer should ignore the start level. If the bit is set to 1, the dimmer will ignore the start level and instead start dimming from its current level. If this bit is set to 0, the dimmer will not ignore the start level.

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 1
Options No (0)      
  Yes (1)      

2: Suspend group 4

Disable transmitting commands to Z-Wave devices that are in Group 4 without disassociating those devices from the group.

Overview

You may wish to disable transmitting commands to Z-Wave devices that are in Group 4 without “disassociating” those devices from the group. Setting parameter 2 to the value of 1 will stop the ZDM230 from transmitting to devices that are “associated” into Group 4. It is possible that you may only want the units in Group 4 to track when the dimmer is being turned ON and OFF and not when dimming.

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

3: Night Light

n night-light mode the LED on the switch will turn ON when the switch is turned OFF.

Overview

The LED on the ZDM230 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1.

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

1: Group 1

Left paddle

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Group 2

Right Paddle

Overview

Right Paddle

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Group 3

Right double click paddle

Overview

Right double click paddle

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Group 4

Group used to inform devices about status updates

Overview

Group used to inform devices about the updates of status of the ZDM230 dimmer

Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.