ZIR010 PIR Motion Sensor

This describes the Z-Wave device ZIR010, manufactured by ACT - Advanced Control Technologies with the thing type UID of act_zir010_00_000.

PIR Motion Sensor

Channels

The following table summarises the channels available for the ZIR010 PIR Motion Sensor.

Channel Channel Id Channel Type UID Category Item Type
Binary Sensor sensor_binary sensor_binary Door Switch
Alarm alarm_general alarm_general Door Switch
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the ZIR010 PIR Motion Sensor. Detailed information on each parameter can be found below.

Parameter Description
17: Mode Notification modes: 0=light, 1=alarm, 2=sensor
18: Off/Idle delay Configuring the off/idle delay
19: Unsolicited Commands Disabling the zir010 trom sending commands unsolicited
22: Awake Time Duration ranges from 15 to 45 seconds. Valid values range from 15 to 45.
1: Motion  
2: Tamper  
3: Battery  

17: Mode

Notification modes: 0=light, 1=alarm, 2=sensor

Overview

The ZIR010 can be configured to operate in 1 of 3 modes. Those modes are:

• Lighting Mode (factory default)
• Alarm Mode
• Sensor Mode

To change the mode of operation:
For Lighting Mode: Send a value of 0 to Configuration Parameter #17.
For Alarm Mode: Send a value of 1 to Configuration Parameter #17.
For Sensor Mode: Send a value of 2 to Configuration Parameter # 17.

Property Value      
Configuration ID config_17_1      
Data Type INTEGER   Default Value 0
Options Lightning (0)      
  Alarm (1)      
  Sensor (2)      

18: Off/Idle delay

Configuring the off/idle delay

Overview

OFF/IDLE (Applicable only when the ZIR010 is configured for Lighting or Binary Sensor Mode).

The ZIR010 will consider there to be “No Activity” after 2 minutes passes during which the ZIR010 detected no motion. At that point, the ZIR010 can be configured to immediately send the OFF or IDLE command or it can be configured to send it from 1 minute to 255 minutes later. (+/- 1 minute).

Property Value
Configuration ID config_18_1
Data Type INTEGER
Range 0 to 255
Default Value 1

19: Unsolicited Commands

Disabling the zir010 trom sending commands unsolicited

Overview

The ZIR010 can be disabled from sending commands unsolicited without removing associated devices by setting Configuration Parameter # 19 to 0 (when asked for number of bytes, select 1). Setting it back to 1 will re-enable the ZIR010. 

Property Value      
Configuration ID config_19_1      
Data Type INTEGER   Default Value 1
Options disabled (0)      
  enabled (1)      

22: Awake Time

Duration ranges from 15 to 45 seconds. Valid values range from 15 to 45.

Overview

The ZIR010 will send a Wakeup Notification Command approximately 3 minutes after power up IF and only IF it has been included into a Z-Wave network. From that point on, the ZIR010 will wake up every 4 hours and re-send the Wakeup Notification Command unless configured for another time interval. The ZIR010 will stay awake by default for 30 seconds and then go back to sleep to conserve battery life.

The time interval between Wakeup Notification Commands can be adjusted if you have a device that supports this. Refer to that device’s instructions.

The time the ZIR010 stays awake can be adjusted from 15 seconds to 45 seconds by sending a value of 15 to 45 to the ZIR010 using Configuration Parameter # 22 (when asked for the number of bytes, select 1). This awake time period starts over every time the ZIR010 receives a command or request. 

Property Value
Configuration ID config_22_1
Data Type INTEGER
Range 15 to 45
Default Value 30

1: Motion

Overview

If the ZIR010 is configured to operate in Lighting Mode, any device that is associated into Group 1 will be sent ON and OFF commands. See OFF/IDLE command section below for how to configure the length of a delay before an OFF command is sent*.

If the ZIR010 is configured to operate in Alarm Mode, any device that is associated into Group 1 will be sent an ALARM command when the ZIR010 detects motion.

If the ZIR010 is configured to operate in Binary Sensor Mode, any device that is associated into Group 1 will be sent an update whenever the ZIR010 detects motion or stops detecting motion.

* See OFF/IDLE command section below to configure the length of a delay before an OFF command is sent.

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Tamper

Overview

If the ZIR010 is configured to operate in Lighting Mode, any device that is associated into Group 2 will be sent ON commands when the housing of the ZIR010 is opened.

If the ZIR010 is configured to operating in Alarm Mode, any device that is associated into Group 2 will be sent an Alarm command when the housing of the ZIR010 is opened.

If the ZIR010 is configured to operate in Binary Sensor Mode, any device that is associated into Group 2 will be sent an update when the housing of the ZIR010 is opened.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Battery

Overview

Any device that is associated into Group 3 will be sent battery level indications at specific intervals. There can be up to 5 devices associated into each group. 

Property Value
Configuration ID group_3
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.