The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

DSB05 4 in One MultiSensor

This describes the Z-Wave device DSB05, manufactured by AEON Labs with the thing type UID of aeon_dsb05_00_000.

The device is in the category of Motion Detector, defining Motion sensors/detectors.

DSB05 product image

The DSB05 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the DSB05 -:

Channel Channel Id Category Item Type
Binary Sensor sensor_binary Door Switch
Sensor (relative humidity) sensor_relhumidity Humidity Number
Sensor (temperature) sensor_temperature Temperature Number
Sensor (luminance) sensor_luminance Temperature Number
Battery Level battery-level Battery Number

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Sensor (relative humidity)

Indicates the current relative humidity.

The sensor_relhumidity channel supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.

Sensor (temperature)

Indicates the current temperature.

The sensor_temperature channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Sensor (luminance)

Indicates the current light reading.

The sensor_luminance channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 11 configuration parameters available in the DSB05. Detailed information on each parameter can be found in the sections below.

Param Name Description
2 Wake up for 10 minutes when batteries are inserted  
3 On time On time before sending off command
4 Motion sensor  
5 Command to send when movement  
101 Which reports to send to group 1 Group 1 automatic report list
102 Which reports to send to group 2 Group 2 automatic report list
103 Which reports to send to group 3 Group 3 automatic report list
111 Interval to send out reports of group 1  
112 Interval to send out reports of group 2  
113 Interval to send out reports of group 3  
255 Reset to the default Configuration of all parameters Set to 1 to reset to factory default
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 2: Wake up for 10 minutes when batteries are inserted

The following option values may be configured -:

Value Description
0 disable (default)
1 enable

The manufacturer defined default value is 0 (disable (default)).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: On time

On time before sending off command How long should the device associated to multi sensor keep state On before sending it Off command (if the value is bigger than 255, the value would be rounded to next integer in minutes) Values in the range 1 to 15300 may be set.

The manufacturer defined default value is 240.

This parameter has the configuration ID config_3_2 and is of type INTEGER.

Parameter 4: Motion sensor

The following option values may be configured -:

Value Description
0 Disabled
1 Enabled

The manufacturer defined default value is 1 (Enabled).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Command to send when movement

The following option values may be configured -:

Value Description
1 Send Basic Set
2 send Sensor Binary report

The manufacturer defined default value is 1 (Send Basic Set).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 101: Which reports to send to group 1

Group 1 automatic report list The value is a combination number made up of the sum of the values for the individual sensors and battery.

The sensors have the values:

Temperature=32

Humidity=64

Lightlevel=128

Battery=1

Therefore if you want all sensors and the battery report set this value to 225 (recommended) Values in the range 0 to 225 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_101_4_000000FF and is of type INTEGER.

Parameter 102: Which reports to send to group 2

Group 2 automatic report list The value is a combination number made up of the sum of the values for the individual sensors and battery.

The sensors have the values:

Temperature=32

Humidity=64

Lightlevel=128

Battery=1

Therefore if you want all sensors and the battery report set this value to 225 Values in the range 0 to 225 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_102_4_000000FF and is of type INTEGER.

Parameter 103: Which reports to send to group 3

Group 3 automatic report list The value is a combination number made up of the sum of the values for the individual sensors and battery.

The sensors have the values:

Temperature=32

Humidity=64

Lightlevel=128

Battery=1

Therefore if you want all sensors and the battery report set this value to 225 Values in the range 0 to 225 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_103_4_000000FF and is of type INTEGER.

Parameter 111: Interval to send out reports of group 1

Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is 720.

This parameter has the configuration ID config_111_4 and is of type INTEGER.

Parameter 112: Interval to send out reports of group 2

Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is 720.

This parameter has the configuration ID config_112_4 and is of type INTEGER.

Parameter 113: Interval to send out reports of group 3

Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is 720.

This parameter has the configuration ID config_113_4 and is of type INTEGER.

Parameter 255: Reset to the default Configuration of all parameters

Set to 1 to reset to factory default

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_255_1_wo and is of type INTEGER. This is a write only parameter.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The DSB05 supports 1 association group.

Group 1: Group 1 devices

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SENSOR_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SENSOR_MULTILEVEL_V5  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.