The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

DSC19 Micro Smart Energy Illuminator G2

This describes the Z-Wave device DSC19, manufactured by AEON Labs with the thing type UID of aeon_dsc19_00_000.

DSC19 product image

The DSC19 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

The Aeon Labs Micro Smart Dimmer (2nd Edition) is a scene multilevel switch device based on Z‐wave enhanced slave library V4.55.00.

Inclusion Information

Include Smart Dimmer into an existing Z‐Wave network: 1. Install Micro Smart Dimmer, and connect Micro Smart Dimmer to an AC‐input power source. 2. Let the primary controller of existing Z‐Wave network into inclusion mode (If you don’t know how to do this, refer to its manual). 3. Press the Z‐Wave button. 4. If the Learning failed, please repeat the process from step 2.

Exclusion Information

Remove Smart Switch from an existing Z‐Wave network: 1. Installed Micro Smart Dimmer, and connect Micro Smart Dimmer to an AC‐ input power source. 2. Let the primary controller of existing Z‐Wave network into remove mode (If you don’t know how to do this, refer to its manual). 3. Press the Z‐Wave button. 4. If the remove failed, please repeat the process from step 2

Channels

The following table summarises the channels available for the DSC19 -:

Channel Channel Id Category Item Type
Dimmer switch_dimmer DimmableLight Dimmer
Electric meter (kWh) meter_kwh Energy Number
Electric meter (volts) meter_voltage Energy Number
Electric meter (watts) meter_watts Energy Number
Electric meter (amps) meter_current Energy Number
Electric Meter (kVah) meter_kvah Energy Number

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Electric meter (kWh)

Indicates the energy consumption (kWh).

The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (volts)

Indicates the instantaneous voltage.

The meter_voltage channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (watts)

Indicates the instantaneous power consumption.

The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (amps)

Indicates the instantaneous current consumption.

The meter_current channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric Meter (kVah)

Indicates the energy consumption (kVAh).

The meter_kvah channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Device Configuration

The following table provides a summary of the 14 configuration parameters available in the DSC19. Detailed information on each parameter can be found in the sections below.

Param Name Description
2 Make Micro Smart Dimmer 2nd Edition Blink The LSB defines the total time the device need to blink.
3 Current Overload Protection Load will be closed when current more that 2.7A and time more than 2 minutes
13 Enable/Disable CRC16 encapsulation Parameter to Enable/Disable CRC16 encapsulation
80 Notification on Status Change Send load notification to associated devices
90 Sending of a Report triggered by minimal change of value. Automated sending of a Report triggered by minimal change of value.
91 Minimum Change to send Report (Watt) The value represents the minimum change in Wattage for a Report to be sent.
92 Minimum Change to send Report (%) The minimum change in Watage Percent for a report to be sent.
101 Reports for Group 1 Which reports need to send automatically in timing intervals for group 1
102 Reports for Group 2 Which reports need to send automatically in timing intervals for group 2
103 Reports for Group 3 Which reports need to send automatically in timing intervals for group 3
111 Interval to send out reports of group 1  
112 Interval to send out reports of group 2  
113 Interval to send out reports of group 3  
120 Turn External Button Mode Parameter to set External button type
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

The LSB defines the total time the device need to blink. This is a double byte value. The LSB defines the total time the device need to blink. The value if set in seconds. The MSB defines the on/off interval of the blinking. The unit is 0.1 s. Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_2_2 and is of type INTEGER.

Parameter 3: Current Overload Protection

Load will be closed when current more that 2.7A and time more than 2 minutes

The following option values may be configured -:

Value Description
0 Deactivate
1 Activate

The manufacturer defined default value is 0 (Deactivate).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 13: Enable/Disable CRC16 encapsulation

Parameter to Enable/Disable CRC16 encapsulation

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Parameter 80: Notification on Status Change

Send load notification to associated devices Parameter to Enable to send notification to associated devices (Group 1) when the state of Micro Smart Dimmer’s load changed The following option values may be configured -:

Value Description
0 Deactivate
1 Hail CC Sent
2 Basic CC Report Sent

The manufacturer defined default value is 0 (Deactivate).

This parameter has the configuration ID config_80_1 and is of type INTEGER.

Parameter 90: Sending of a Report triggered by minimal change of value.

Automated sending of a Report triggered by minimal change of value. Parameter to Enable/Disable automated sending of a Report triggered by minimal change of value. The following option values may be configured -:

Value Description
0 Deavtivate
1 Activate

The manufacturer defined default value is 0 (Deavtivate).

This parameter has the configuration ID config_90_1 and is of type INTEGER.

Parameter 91: Minimum Change to send Report (Watt)

The value represents the minimum change in Wattage for a Report to be sent.

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 25.

This parameter has the configuration ID config_91_2 and is of type INTEGER.

Parameter 92: Minimum Change to send Report (%)

The minimum change in Watage Percent for a report to be sent. The value represents the minimum change in Watage Percent for a report to be sent. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 5.

This parameter has the configuration ID config_92_1 and is of type INTEGER.

Parameter 101: Reports for Group 1

Which reports need to send automatically in timing intervals for group 1 The value is a combination number made up of the sum of the values for the individual parameters. The parameters have the values: KWH=8, Wattage=4, Current=2, Voltage=1. Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_101_4 and is of type INTEGER.

Parameter 102: Reports for Group 2

Which reports need to send automatically in timing intervals for group 2 The value is a combination number made up of the sum of the values for the individual parameters. The parameters have the values: KWH=8, Wattage=4, Current=2, Voltage=1. Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 8.

This parameter has the configuration ID config_102_4 and is of type INTEGER.

Parameter 103: Reports for Group 3

Which reports need to send automatically in timing intervals for group 3 The value is a combination number made up of the sum of the values for the individual parameters. The parameters have the values: KWH=8, Wattage=4, Current=2, Voltage=1. Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_103_4 and is of type INTEGER.

Parameter 111: Interval to send out reports of group 1

Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_111_4 and is of type INTEGER.

Parameter 112: Interval to send out reports of group 2

Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is 600.

This parameter has the configuration ID config_112_4 and is of type INTEGER.

Parameter 113: Interval to send out reports of group 3

Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is 600.

This parameter has the configuration ID config_113_4 and is of type INTEGER.

Parameter 120: Turn External Button Mode

Parameter to set External button type

The following option values may be configured -:

Value Description
0 Momentary Button Mode
1 2 State Switch Mode
2 3 Way Switch Mode

The manufacturer defined default value is 255.

This parameter has the configuration ID config_120_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The DSC19 supports 2 association groups.

Group 1: Target for automatic meter reports

This group supports 5 nodes.

Group 2: Target for automatic reports

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V2 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_SCENE_ACTIVATION_V1  
COMMAND_CLASS_SCENE_ACTUATOR_CONF_V0  
COMMAND_CLASS_METER_V3  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.