The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZW140 Dual Nano Switch

This describes the Z-Wave device ZW140, manufactured by AEON Labs with the thing type UID of aeon_zw140_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

ZW140 product image

The ZW140 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

Aeotec Dual Nano Switch is a Z-Wave Smart Switch specifically used to enable Z-Wave command and control (on/off) of any wall switches.
In the event of power failure, non-volatile memory retains all programmed information relating to the unit’s operating status.
It can connect to 2 external manual switches to control the load ON/OFF independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Dual Nano Switch.
The Dual Nano Switch is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.

Channels

The following table summarises the channels available for the ZW140 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Scene Number scene_number   Number
Alarm (heat) alarm_heat   Switch
Clock Time Offset time_offset Temperature Number
Switch 1 switch_binary1 Switch Switch
Switch 2 switch_binary2 Switch Switch

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Scene Number

Triggers when a scene button is pressed.

The scene_number channel supports the Number item.

Alarm (heat)

Indicates if a heat alarm is triggered.

The alarm_heat channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Clock Time Offset

Provides the current time difference for the devices time.

The time_offset channel supports the Number item and is in the Temperature category.

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Switch 2

Switch the power on and off.

The switch_binary2 channel supports the Switch item and is in the Switch category.

Device Configuration

The following table provides a summary of the 14 configuration parameters available in the ZW140. Detailed information on each parameter can be found in the sections below.

Param Name Description
4 Overheat protection. Overheat protection.
20 Configure the output status after re-power on it. Configure the output status after re-power on it.
80 Group 1 notifications To set which notification would be sent to the associated devices (Group 1)
81 Group 3 notifications Group 3 notifications
82 Group 4 notifications Group 4 notifications
83 Configure the state of LED when it is in 3 modes Configure the state of LED when it is in 3 modes
84 ON/OFF time in Night light mode. Set the ON/OFF time of the LED when it is in Night light mode.
86 Set appointment 1 Set appointment 1
87 Set appointment 2 Set appointment 2
120 Configure the external switch mode for S1 Configure the external switch mode for S1
121 Configure the external switch mode for S2. Configure the external switch mode for S2.
122 Set the control destination for external switch Set the control destination for external switch
252 Lock/unlock configuration parameters Lock/unlock configuration parameters
255 Reset the Dual Nano Switch Reset the Dual Nano Switch
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 4: Overheat protection.

Overheat protection.

The following option values may be configured -:

Value Description
0 Disable
1 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 20: Configure the output status after re-power on it.

Configure the output status after re-power on it.

The following option values may be configured -:

Value Description
0 Last status
1 Always on
2 Always off

The manufacturer defined default value is 0 (Last status).

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Parameter 80: Group 1 notifications

To set which notification would be sent to the associated devices (Group 1)

The following option values may be configured -:

Value Description
0 Send Nothing
1 Send Hail CC
2 Send Basic CC report
3 Send Hail CC when using the manual switch

The manufacturer defined default value is 0 (Send Nothing).

This parameter has the configuration ID config_80_1 and is of type INTEGER.

Parameter 81: Group 3 notifications

Group 3 notifications To set which notification would be sent to the associated nodes in association group 3 The following option values may be configured -:

Value Description
0 Send Nothing
1 Send Basic Set CC

The manufacturer defined default value is 1 (Send Basic Set CC).

This parameter has the configuration ID config_81_1 and is of type INTEGER.

Parameter 82: Group 4 notifications

Group 4 notifications To set which notification would be sent to the associated nodes in association group 4 The following option values may be configured -:

Value Description
0 Send Nothing
1 Send Basic Set CC

The manufacturer defined default value is 1 (Send Basic Set CC).

This parameter has the configuration ID config_82_1 and is of type INTEGER.

Parameter 83: Configure the state of LED when it is in 3 modes

Configure the state of LED when it is in 3 modes

The following option values may be configured -:

Value Description
0 Energy mode. The LED will follow the status (on/off).
1 Momentary indicate mode
2 Night light mode. The LED will remain ON state.

The manufacturer defined default value is 0 (Energy mode. The LED will follow the status (on/off).).

This parameter has the configuration ID config_83_1 and is of type INTEGER.

Parameter 84: ON/OFF time in Night light mode.

Set the ON/OFF time of the LED when it is in Night light mode. 0 to 60 The minute time of OFF 256 to 316 The hour time of OFF 65536 to 65596 The minute time of ON 16777216 to 16777276 The hour time of ONThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 16777276 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_84_4 and is of type INTEGER.

Parameter 86: Set appointment 1

Set appointment 1 256 to 316 The hour value of ON time 16777215 Disable the setting. 0 to 60 The minute value of ON time 65536 to 65543 The day value (Mon to Sun) 16777216 Enable the setting.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 16777216 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_86_4 and is of type INTEGER.

Parameter 87: Set appointment 2

Set appointment 2 256 to 316 The hour value of ON time 65536 to 65543 The day value (Mon to Sun) 16777215 Disable the setting. 0 to 60 The minute value of ON time 16777216 Enable the setting.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 16777216 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_87_4 and is of type INTEGER.

Parameter 120: Configure the external switch mode for S1

Configure the external switch mode for S1

The following option values may be configured -:

Value Description
0 Enter automatic identification mode
1 2-state switch mode
2 3 way switch mode
3 Momentary push button mode

The manufacturer defined default value is 0 (Enter automatic identification mode).

This parameter has the configuration ID config_120_1 and is of type INTEGER.

Parameter 121: Configure the external switch mode for S2.

Configure the external switch mode for S2.

The following option values may be configured -:

Value Description
0 Enter automatic identification mode
1 2-state switch mode
2 3 way switch mode
3 Momentary push button mode

The manufacturer defined default value is 0 (Enter automatic identification mode).

This parameter has the configuration ID config_121_1 and is of type INTEGER.

Parameter 122: Set the control destination for external switch

Set the control destination for external switch

The following option values may be configured -:

Value Description
1 control the output loads of itself.
2 control the other nodes
3 control the output loads of itself and other nodes.

The manufacturer defined default value is 3 (control the output loads of itself and other nodes.).

This parameter has the configuration ID config_122_1 and is of type INTEGER.

Parameter 252: Lock/unlock configuration parameters

Lock/unlock configuration parameters

The following option values may be configured -:

Value Description
0 Unlock
1 Lock

The manufacturer defined default value is 0 (Unlock).

This parameter has the configuration ID config_252_1 and is of type INTEGER.

Parameter 255: Reset the Dual Nano Switch

Reset the Dual Nano Switch

The following option values may be configured -:

Value Description
0 Reset all configuration parameters
1431655765 Reset to factory default

The manufacturer defined default value is 0 (Reset all configuration parameters).

This parameter has the configuration ID config_255_4 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZW140 supports 4 association groups.

Group 1: Lifeline

Z-Wave Plus Lifeline. When the load state of Dual Nano Switch (turn on/off the load) is changed, the Hail CC and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group. This group supports 5 nodes.

Group 2: Forward the Basic Set

Forward the Basic Set, Switch All, Scene Activation Set to associated nodes in Group 2 when the Dual Nano Switch receives the Basic Set, Switch All, Scene Activation Set commands from main controller. (E.g. Send/forward Basic Set to control the other node This group supports 5 nodes.

Group 3: Send Basic Set (configured by parameter 0x51 )

Send Basic Set (configured by parameter 0x51 ) to the associated nodes in Group 3 when the external switch S1 is operated. Note: The Switch Mode of external switch S1 should be identified successfully, which means that the value of Configuration parameter This group supports 5 nodes.

Group 4: Send Basic Set (configured by parameter 0x52)

Send Basic Set (configured by parameter 0x52) to the associated nodes in Group 4 when the external switch S2 is operated. Note: The Switch Mode of external switch S2 should be identified successfully, which means that the value of Configuration parameter This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V1| | | COMMAND_CLASS_SCENE_ACTIVATION_V1| | | COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V4| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_POWERLEVEL_V1| | | COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| | | COMMAND_CLASS_CLOCK_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |

Endpoint 2

Command Class Comment
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.