DSC13 Micro Smart Energy Illuminator
This describes the Z-Wave device DSC13, manufactured by AEON Labs with the thing type UID of aeon_dsc13_00_000.
Micro Smart Energy Illuminator
Channels
The following table summarises the channels available for the DSC13 Micro Smart Energy Illuminator.
| Channel | Channel Id | Channel Type UID | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Sensor (power) | sensor_power | sensor_power | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
Dimmer
Restore Last Value
Restore Last Dimming level on ON.
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_restoreLastValue | |||
| Data Type | BOOLEAN | Default Value | true | |
| Options | Restore Last Value (true) | |||
| Restore Full Brightness (false) |
Device Configuration
The following table provides a summary of the configuration parameters available in the DSC13 Micro Smart Energy Illuminator. Detailed information on each parameter can be found below.
| Parameter | Description |
|---|---|
| 1: Type of Sensor Report | Defines the value type to be sent as Sensor Report. |
| 2: Blinking Behavior | See overview |
| 80: Notification on Status Change | Type of report to send when the device status changes |
| 90: Disable Minimum Change report | |
| 91: Minimum Change to send Report (Watt) | The minimum change in Wattage for a Report to be sent |
| 92: Minimum Change to send Report (%) | The minimum change in Wattage Percent for a report to be sent |
| 101: Reports to send to Group 1 | See overview |
| 102: Reports to send to Group 2 | See overview |
| 103: Reports to send to Group 3 | See overview |
| 111: Interval to send out reports of group 1 | Time interval to send report to Group 1 |
| 112: Interval to send out reports of group 2 | Time interval to send report to Group 2 |
| 113: Interval to send out reports of group 3 | Time interval to send report to Group 3 |
| 1: Group 1 | Status Reports |
| 2: Group 2 | |
| 3: Group 3 |
1: Type of Sensor Report
Defines the value type to be sent as Sensor Report.
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_1_1 | |||
| Data Type | INTEGER | |||
| Range | 0 to 1 | Default Value | 0 | |
| Options | Power (0) | |||
| Voltage (1) |
2: Blinking Behavior
See overview
Overview
The LSB defines the total time the device need to blink. The value if set in seconds. The MSB defines the on/off interval of the blinking. The unit is 0.1 s.
| Property | Value |
|---|---|
| Configuration ID | config_2_2 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 0 |
80: Notification on Status Change
Type of report to send when the device status changes
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_80_1 | |||
| Data Type | INTEGER | |||
| Range | 0 to 2 | Default Value | 0 | |
| Options | Nothing (0) | |||
| Hail (1) | ||||
| Basic CC Report (2) |
90: Disable Minimum Change report
| Property | Value | |||
|---|---|---|---|---|
| Configuration ID | config_90_1 | |||
| Data Type | INTEGER | |||
| Range | 0 to 1 | Default Value | 0 | |
| Options | Disabled (0) | |||
| Enabled (1) |
91: Minimum Change to send Report (Watt)
The minimum change in Wattage for a Report to be sent
| Property | Value |
|---|---|
| Configuration ID | config_91_2 |
| Data Type | INTEGER |
| Range | 0 to 32000 |
| Default Value | 50 |
92: Minimum Change to send Report (%)
The minimum change in Wattage Percent for a report to be sent
| Property | Value |
|---|---|
| Configuration ID | config_92_1 |
| Data Type | INTEGER |
| Range | 0 to 100 |
| Default Value | 10 |
101: Reports to send to Group 1
See overview
Overview
The value is a combination number made up of the sum of the values for the individual parameters. The parameters have the values: Wattage=4, Current=2, Voltage=1.
| Property | Value |
|---|---|
| Configuration ID | config_101_4 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 4 |
102: Reports to send to Group 2
See overview
Overview
The value is a combination number made up of the sum of the values for the individual parameters. The parameters have the values: Wattage=4, Current=2, Voltage=1.
| Property | Value |
|---|---|
| Configuration ID | config_102_4 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 4 |
103: Reports to send to Group 3
See overview
Overview
The value is a combination number made up of the sum of the values for the individual parameters. The parameters have the values: Wattage=4, Current=2, Voltage=1.
| Property | Value |
|---|---|
| Configuration ID | config_103_4 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 4 |
111: Interval to send out reports of group 1
Time interval to send report to Group 1
| Property | Value |
|---|---|
| Configuration ID | config_111_4 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 720 |
112: Interval to send out reports of group 2
Time interval to send report to Group 2
| Property | Value |
|---|---|
| Configuration ID | config_112_4 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 720 |
113: Interval to send out reports of group 3
Time interval to send report to Group 3
| Property | Value |
|---|---|
| Configuration ID | config_113_4 |
| Data Type | INTEGER |
| Range | 0 to 65535 |
| Default Value | 720 |
1: Group 1
Status Reports
| Property | Value |
|---|---|
| Configuration ID | group_1 |
| Data Type | TEXT |
| Range | to |
2: Group 2
| Property | Value |
|---|---|
| Configuration ID | group_2 |
| Data Type | TEXT |
| Range | to |
3: Group 3
| Property | Value |
|---|---|
| Configuration ID | group_3 |
| Data Type | TEXT |
| Range | to |
Did you spot an error in the above definition or want to improve the content? You can edit the database here.