ZW056 Doorbell

This describes the Z-Wave device ZW056, manufactured by AEON Labs with the thing type UID of aeon_zw056_00_000.

Doorbell

Overview

Aeon Labs Doorbell is a switch binary device based on Z-wave enhanced slave library V6.51.06.

The Doorbell supports playing MP3 music files with a press of this doorbell. It has a 16MB flash memory that can store up to 100 ringtones. The volume can be adjusted manually via short press on the Volume Button, also you can switch the doorbell sound to the next via long press on the Volume Button. You may change/update your doorbell ringtone at any point in time you want by connecting your Doorbell to your PC to update the sound track on your Doorbell’s flash memory. 

Inclusion Information

  1. Install Doorbell, and plug it into the socket of AC Power.
  2. Let the primary controller into inclusion mode (If you don’t know how to do this, please refer to its manual).
  3. Press the Action Button.
  4. If the inclusion is failed, please repeat the process from step 2. 

Exclusion Information

  1. Install Doorbell, and plug it into the socket of AC Power.
  2. Let the primary controller into exclusion mode (If you don’t know how to do this, refer to its manual).
  3. Press the Action Button.
  4. If the remove is failed, please repeat the process from step 2.

Note: If Doorbell is removed from Z-wave network, it will be reset to factory default. 

Channels

The following table summarises the channels available for the ZW056 Doorbell.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Volume config_decimal_param8 config_decimal   Decimal
Repititions config_decimal_param2 config_decimal   Decimal
Play Chime Now config_decimal_param6 aeon_zw056_00_000_config_decimal_param6    
Doorbell Notifications config_decimal_param80 aeon_zw056_00_000_config_decimal_param80    
Button Battery Status config_decimal_param42 aeon_zw056_00_000_config_decimal_param42    

Device Configuration

The following table provides a summary of the configuration parameters available in the ZW056 Doorbell. Detailed information on each parameter can be found below.

Parameter Description
2: Repetitions of ringtone Set the repetitions for playing doorbell ringtone. 
5: Default ringtone Set the default doorbell ringtone. Default=1
8: Ringtone volume Default=10
10: Define button- and button+ action Define functions of “Button ‐”  and “Button+”.
11: Define long press button- and button+ Define short/long button presses
42: Get wireless button battery status Alert for low battery
80: Enable Notifications Enable to send notifications to associated devices (Group1)
81: Enable/disable battery group notification Notifies Group 1 when battery state is low
241: Pair doorbell with button Starts wireless button pairing mode
252: Lock configuration Lock configuration
255: Reset Reset to factory settings
6: Ringtone to play Set a ringtone to play. Default=0
7: Control items Control current output
1: Group 1  
2: Forward basic set  

2: Repetitions of ringtone

Set the repetitions for playing doorbell ringtone. 

Overview

Value=1 to 255, the range of repetition is 1 to 100.   Value =0, ignore. Note: If the time of playing doorbell ringtone is more than 20s, the volume of ringtone will reduce to silence no matter how many repetitions of doorbell ringtone are set. 

Property Value
Configuration ID config_2_1
Data Type INTEGER
Range 0 to 100
Default Value 2

5: Default ringtone

Set the default doorbell ringtone. Default=1

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 1 to 100
Default Value 1

8: Ringtone volume

Default=10

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 10
Default Value 10

10: Define button- and button+ action

Define functions of “Button ‐”  and “Button+”.

Overview

0:  button- is previous, button+ is next

1:  button- is next, button+ is previous

Property Value      
Configuration ID config_10_1      
Data Type INTEGER   Default Value 0
Options “Button ‐” is previous, “Button+” is next (0)      
  “Button ‐” is next, “Button+” is previous (1)      

11: Define long press button- and button+

Define short/long button presses

Overview

0: short pressing changes volume, long pressing changes
default ringtone.
1: long pressing changes volume, short pressing changes
default ringtone.

Property Value      
Configuration ID config_11_1      
Data Type INTEGER   Default Value 0
Options short press changes vol, long press changes default ringtone (0)      
  long press changes vol, short press changes default ringtone (1)      

42: Get wireless button battery status

Alert for low battery

Overview

0x00:  normal battery level

0xff:  low battery level

set 0x00:  cancel low battery alert

Property Value      
Configuration ID config_42_1      
Data Type INTEGER   Default Value 0
Options Battery Level Good (0)      
  Low Battery (255)      

80: Enable Notifications

Enable to send notifications to associated devices (Group1)

Overview

Enable/disable to send notifications to associated devices (Group 1) when the state of Doorbell is changed (0=nothing, 1=hail CC, 2=basic CC report)

Property Value      
Configuration ID config_80_1      
Data Type INTEGER   Default Value 0
Options nothing (0)      
  hail CC (1)      
  basic CC report (2)      

81: Enable/disable battery group notification

Notifies Group 1 when battery state is low

Overview

Enable/disable to send notifications to associated devices (Group
1) when the Wireless Button’s battery is in low battery state
(0=nothing, 1=Configuration report 0x2A)

Property Value      
Configuration ID config_81_1      
Data Type INTEGER   Default Value 0
Options nothing (0)      
  Configuration report parameter 42 (1)      

241: Pair doorbell with button

Starts wireless button pairing mode

Overview

Pair the Wireless Button with Doorbell.
Value=0x55555555, Start the Wireless Button pairing mode and
the blue Led will blink slowly, short press the Wireless Button
once, if the blue Led change to be solid, which means the pairing
is successful. Otherwise, repeat the steps.
It will automatically exit the pairing mode after 8s if there is no
pressing action of the Wireless Button.
Note:
You can send this configuration Get CC to ask the pairing result:
If configuration report value=0x00000000, which means the
pairing is failed.
If configuration report value =0xFFFFFFFF, which means the
pairing is successful.

Property Value
Configuration ID config_241_4
Data Type INTEGER
Range 0 to 4294967295
Default Value 0

252: Lock configuration

Lock configuration

Overview

0:  config not locked

1:  config locked

Property Value
Configuration ID config_252_1
Data Type INTEGER
Range 0 to 1
Default Value 0

255: Reset

Reset to factory settings

Overview
  1. Size=0x01, Configuration Value=0x00:
    Reset configuration setting.
  2. Size=0x04, Configuration Value=0x55555555:
    Reset Factory setting.
Property Value
Configuration ID config_255_4
Data Type INTEGER
Range 0 to 4294967295
Default Value 0

6: Ringtone to play

Set a ringtone to play. Default=0

Overview

Set this to any ringtone (1-100) to have it play that ringtone.

Property Value      
Configuration ID config_6_1_wo      
Data Type INTEGER      
Range 0 to 100   Default Value 0
Options Stop (0)      
  play the default ringtone (255)      

7: Control items

Control current output

Overview

Control items: Value=1, play Value=2, stop Value=3, pause Value=4, Next Value=5, Previous Other, ignore

Property Value      
Configuration ID config_7_1_wo      
Data Type INTEGER   Default Value 0
Options Ignore (0)      
  Play (1)      
  Stop (2)      
  Pause (3)      
  Next (4)      
  Previous (5)      

1: Group 1

Overview

When the state of Doorbell (trigger to turn on/off the rington
e ) is changed:
1, Set Configuration parameter 80 to 0: Reserved (Default).
2, Set Configuration parameter 80 to 1: Send Hail CC.

  1. Set Configuration parameter 80 to 2: Send the Basic
    Report.
Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Forward basic set

Overview

Forward the Basic Set, Switch Binary Set, Switch Multilevel
Start Level Change, Switch Multilevel Stop Level Change,
Switch Multilevel Set, Scene Activation Set to associated
nodes in Group 2 when the Doorbell receives the Basic Set,
Switch Binary Set, Switch Multilevel Start Level Change,
Switch Multilevel Stop Level Change, Switch Multilevel Set,
Scene Activation Set commands from main controller.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.