ZW090 Z‐Stick Gen5 USB Controller

This describes the Z-Wave device ZW090, manufactured by AEON Labs with the thing type UID of aeon_zw090_00_000.

Z‐Stick Gen5 USB Controller

Overview

Aeon Labs Z‐Stick Gen5 is a self‐powered Z‐Wave USB adapter with remote network creation capabilities
(independent from external power and host microprocessor).  By being able to remotely include/remove Z‐
Wave devices, this greatly simplifies Z‐Wave network installation.  When connected to a host controller (via
USB), it enables the host controller to take part in the Z‐Wave Network.
It can be included and operated in any Z‐wave network with other Z‐wave certified devices from other
manufacturers and/or other applications. All non‐battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the network. 

Inclusion Information

Push the include button.  Controller will blink slowly.  It is in include mode.  Press again to cancel.

Exclusion Information

  1. Unplug the Z‐Stick from the USB connector. Then press and hold the Action Button for
    approximately 2 seconds. (The orange LED will blinking fast.)
  2. To remove a Z‐Wave device from the network, simply go to the device with the Z‐Stick
    and press the Action Button on the device you wish to remove. (The LED on the Z‐Stick will
    become blue and Immediately stay solid for 2 seconds to indicate successful removal from
    the network.)
    3.   The orange LED will then return to blinking fast, indicating readiness for further device
    exclusions. Repeat step 1 for each device as you wish to exclude

Wakeup Information

N/A

Channels

The following table summarises the channels available for the ZW090 Z‐Stick Gen5 USB Controller.

| Channel | Channel Id | Channel Type UID | Category | Item Type | |———|————|——————|———-|———–|

Device Configuration

The following table provides a summary of the configuration parameters available in the ZW090 Z‐Stick Gen5 USB Controller. Detailed information on each parameter can be found below.

Parameter Description
81: Enable/disable the LED indicator This parameter is used to enable/disable the LED indicator.
220: RF power level RF power level
242: Security network enabled Security network enabled
243: Security Network Key Security Network Key
252: Lock Configuration Configuration lock. 1=enable, 0=disable
1: Z-Stick Gen5 (ZW090-A) Z-Wave Plus Lifeline

81: Enable/disable the LED indicator

This parameter is used to enable/disable the LED indicator.

Overview

When the USB power supply, the LED indicator light configuration

(0 =disable, 1 = enable)

Property Value      
Configuration ID config_81_1      
Data Type INTEGER   Default Value 1
Options Disable (0)      
  (0)      
  Enable (1)      

220: RF power level

RF power level

Overview

Configuration of the RF power level

1~10, other= ignore. A total of 10 levels, level 1
as the weak output power, and so on, 10 for
most output power level.

Property Value
Configuration ID config_220_1
Data Type INTEGER
Range 1 to 10
Default Value 10

242: Security network enabled

Security network enabled

Overview

Security network enabled
(0 =disable, 1 = enable)

Property Value      
Configuration ID config_242_1      
Data Type INTEGER   Default Value 0
Options disable (0)      
  enable (1)      

243: Security Network Key

Security Network Key

Property Value
Configuration ID config_243_16
Data Type INTEGER
Range 0 to 4294967295
Default Value 0

252: Lock Configuration

Configuration lock. 1=enable, 0=disable

Overview

Enable/disable Lock Configuration (0 =disable, 1= enable, other= ignore)

Property Value      
Configuration ID config_252_1      
Data Type INTEGER   Default Value 0
Options disable (0)      
  enable (1)      

1: Z-Stick Gen5 (ZW090-A)

Z-Wave Plus Lifeline

Property Value
Configuration ID group_1
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.