ZW121 Aeotec LED Strip

This describes the Z-Wave device ZW121, manufactured by AEON Labs with the thing type UID of aeon_zw121_00_000.

Aeotec LED Strip

Overview

Aeotec LED Strip has been crafted to power connected lighting using Z-Wave Plus. It is powered by Aeotec’s Gen5 technology. The LED Strip is a multi-colored LED Strip which allows control (on/off/dim/color change) via Z-Wave commands.

Note that configuration parameters 37 and 39 only apply when the strip is in color transition mode. Color transition mode is entered when a change to parameter 37 or 39 is submitted. Color transition mode is exited when a change to any of the channels is submitted. 

Inclusion Information

  1. Set your Z-Wave controller into pairing mode.
  2. Press the Action Button located on the back of the LED Strip’s white controller box once (The network LED will blink green as an indication it is pairing insecurely, please refer to section “Enabling Security Encryption” in the Advanced Function section of the manual to pair it securely).
  3. If the LED Strip has been successfully added to your Z-Wave network, its Network LED will become solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the instructions above from step 1. 

Exclusion Information

  1. Set your Z-Wave controller into device removal mode.
  2. Press the Action Button located on the back of the LED Strip’s white controller box once.
  3. If the LED Strip has been successfully removed from your  Z-Wave network, its Network LED will remain colorful gradient. If the removal was unsuccessful, the Network LED will still be solid, repeat the instructions above from step 1.

Channels

The following table summarises the channels available for the ZW121 Aeotec LED Strip.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer
Scene Number scene_number scene_number   Number
Color Control color_color color_color   Color
Color Temperature color_temperature color_temperature ColorLight Dimmer
Configuration Parameter 37 meter_current_param37 aeon_zw121_00_000_meter_current_param37   Number

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the ZW121 Aeotec LED Strip. Detailed information on each parameter can be found below.

Parameter Description
37: Color Change Speed Level Applies only when the Color Transition Style is set to Fade Out/In
37: Time Base of Color Change Speed Applies only when the Color Transition Style is set to Fade Out/In
37: Cycle Count Defines the number of repetitions of the color transition cycle
37: Brightness Brightness when in color transition mode
37: Color Display Cycle Defines the mode for determining colors used in color transitions
37: Color Change Speed Option Applies only when the Color Transition Style is set to Fade Out/In
37: Color Transition Style Defines how the strip transitions between colors
39: Multi Color, Single Color or Random Mode - Byte 4 todo
39: Multi Color, Single Color, or Random Mode - Byte 3 todo
39: Multi Color, Single Color, or Random Mode - Byte 2 todo
39: Multi Color, Single Color, or Random Mode - Byte 1 todo
80: Notifications for Association Group 1 Send notifications about strip state changes to association group 1
1: Lifeline Notification group for strip state changes
2: Retransmit Retransmit commands to associated nodes

37: Color Change Speed Level

Applies only when the Color Transition Style is set to Fade Out/In

Overview

Value 0 means constant speed. Value 1-30 sets the speed to accelerate/decelerate. 

Property Value      
Configuration ID config_37_4_0000001F      
Data Type INTEGER      
Range 0 to 30   Default Value 0
Options (0)      

37: Time Base of Color Change Speed

Applies only when the Color Transition Style is set to Fade Out/In

Overview

Amount of time spent to transition between colors.

Property Value      
Configuration ID config_37_4_000000E0      
Data Type INTEGER   Default Value 0
Options Time base is 1s (0)      
  Time base is 10ms (1)      
  Time base is 100ms (2)      

37: Cycle Count

Defines the number of repetitions of the color transition cycle

Overview

When the end is reached the strip turns off.

Property Value
Configuration ID config_37_4_0000FF00
Data Type INTEGER
Range 0 to 254
Default Value 0

37: Brightness

Brightness when in color transition mode

Overview

Note that this setting only affects the brightness when in color transition mode. Use the “Brightness” channel to set the brightness outside of color transition mode.

Property Value
Configuration ID config_37_4_00FF0000
Data Type INTEGER
Range 1 to 99
Default Value 99

37: Color Display Cycle

Defines the mode for determining colors used in color transitions

Overview

Note that “Single Color Mode” does not select a constant single color (as the “Color Control” channel does), but instead cycles through a single color. 

Property Value      
Configuration ID config_37_4_07000000      
Data Type INTEGER   Default Value 1
Options Inactive (keep the current configuration value) (0)      
  Rainbow mode (1)      
  Multi color mode (colors cycle between selected colors) (2)      
  Random mode (3)      
  Single color mode (4)      

37: Color Change Speed Option

Applies only when the Color Transition Style is set to Fade Out/In

Property Value      
Configuration ID config_37_4_38000000      
Data Type INTEGER   Default Value 0
Options Fade in for 1/2 second and fade out for 1/2 second (0)      
  Fade in for 5ms and fade out for 5ms (1)      
  Fade in for 50ms and fade out for 50ms (2)      

37: Color Transition Style

Defines how the strip transitions between colors

Overview

Note that “Smooth Color Transition” will lead to invisible transitions when “Color Display Cycle” is set to “Single Color Mode”.

Property Value      
Configuration ID config_37_4_40000000      
Data Type INTEGER   Default Value 0
Options Smooth color transition (0)      
  Fade out fade in transition (1)      

39: Multi Color, Single Color or Random Mode - Byte 4

todo

Property Value
Configuration ID config_39_4_000000FF
Data Type INTEGER
Range 0 to 5
Default Value 0

39: Multi Color, Single Color, or Random Mode - Byte 3

todo

Property Value
Configuration ID config_39_4_0000FF00
Data Type INTEGER
Range 0 to 5
Default Value 3

39: Multi Color, Single Color, or Random Mode - Byte 2

todo

Property Value
Configuration ID config_39_4_00FF0000
Data Type INTEGER
Range 0 to 4294967295
Default Value 0

39: Multi Color, Single Color, or Random Mode - Byte 1

todo

Property Value
Configuration ID config_39_4_7F000000
Data Type INTEGER
Range 0 to 5
Default Value 3

80: Notifications for Association Group 1

Send notifications about strip state changes to association group 1

Property Value      
Configuration ID config_80_1      
Data Type INTEGER   Default Value 1
Options No notifications (0)      
  Hail CC (1)      
  Basic CC report (2)      

1: Lifeline

Notification group for strip state changes

Overview

 Use configuration parameter 80 to define what notifications this group receives.

 

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Retransmit

Retransmit commands to associated nodes

Overview

Forward the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set to associated nodes in this group when the LED Strip receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller. 

Property Value
Configuration ID group_2
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.