The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

RF9501 15A Light Switch

This describes the Z-Wave device RF9501, manufactured by Cooper Wiring Devices with the thing type UID of cooper_rf9501_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

RF9501 product image

The RF9501 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the RF9501 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Scene Number scene_number   Number
Alarm alarm_general Door Switch

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Scene Number

Triggers when a scene button is pressed.

The scene_number channel supports the Number item.

Alarm

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Device Configuration

The following table provides a summary of the 6 configuration parameters available in the RF9501. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Delayed OFF time The time in seconds the switch will delay when trigger the delayed off feature
2 Panic ON time The time in seconds the switch will turn on for when panic mode is triggered
3 Panic OFF time The time in seconds the switch will turn off for when panic mode is triggered
4 Basic Set Value Setting this to anything other than 0 will cause the value to be transmitted to devices in the association group when the switch is triggered. A setting other than 0 will likely result in undesired operation
5 Power Up State Power Up State of the switch
6 Panic mode enable Enables this switch to participate in panic mode
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Delayed OFF time

The time in seconds the switch will delay when trigger the delayed off feature

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Panic ON time

The time in seconds the switch will turn on for when panic mode is triggered

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Panic OFF time

The time in seconds the switch will turn off for when panic mode is triggered

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Basic Set Value

Setting this to anything other than 0 will cause the value to be transmitted to devices in the association group when the switch is triggered. A setting other than 0 will likely result in undesired operation

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Power Up State

Power Up State of the switch

The following option values may be configured -:

Value Description
1 OFF
2 ON
3 Last State

The manufacturer defined default value is 1 (OFF).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 6: Panic mode enable

Enables this switch to participate in panic mode

The following option values may be configured -:

Value Description
1 OFF
2 ON

The manufacturer defined default value is 1 (OFF).

This parameter has the configuration ID config_6_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The RF9501 supports 1 association group.

Group 1: Group 1

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_SCENE_ACTIVATION_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_NODE_NAMING_V1  
COMMAND_CLASS_HAIL_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_INDICATOR_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.