RF9536-N 1000W Dimmer Light Switch

This describes the Z-Wave device RF9536-N, manufactured by Cooper Wiring Devices with the thing type UID of cooper_rf9536n_00_000.

1000W Dimmer Light Switch

Channels

The following table summarises the channels available for the RF9536-N 1000W Dimmer Light Switch.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer
Scene Number scene_number scene_number   Number
Dimmer Ramp Time config_decimal_param7 config_decimal   Decimal
Alarm alarm_general alarm_general Door Switch

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the RF9536-N 1000W Dimmer Light Switch. Detailed information on each parameter can be found below.

Parameter Description
1: Delayed OFF time time in seconds to delay OFF
2: Panic ON time Time in seconds for panic mode ON
3: Panic OFF time time in seconds for OFF in panic mode
4: Basic Set Value Send value to association group on trigger
5: Power Up State Power Up State of the switch
6: Panic mode enable Enables this switch to participate in panic mode
7: Dimmer Ramp Time Time in seconds to reach desired level
8: Kickstart / Rapid Start Turn on or off rapid start feature
11: Minimum Dimmer Level The minimum dim level the switch will allow
12: Maximum Dimmer Level The maximum dim level the switch will allow
1: Group 1  
255: Group 255  

1: Delayed OFF time

time in seconds to delay OFF

Overview

The amount of time in seconds the switch will delay when trigger the delayed off feature

Property Value
Configuration ID config_1_1
Data Type INTEGER
Range 0 to 255
Default Value 0

2: Panic ON time

Time in seconds for panic mode ON

Overview

The amount of time in seconds the switch will turn on for when panic mode is triggered

Property Value
Configuration ID config_2_1
Data Type INTEGER
Range 0 to 255
Default Value 0

3: Panic OFF time

time in seconds for OFF in panic mode

Overview

The amount of time in seconds the switch will turn off for when panic mode is triggered

Property Value
Configuration ID config_3_1
Data Type INTEGER
Range 0 to 255
Default Value 0

4: Basic Set Value

Send value to association group on trigger

Overview

Setting this to anything other than 0 will cause the value to be transmitted to devices in the association group when the switch is triggered. A setting other than 0 will likely result in undesired operation

Property Value
Configuration ID config_4_1
Data Type INTEGER
Range 0 to 255
Default Value 0

5: Power Up State

Power Up State of the switch

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 1
Options OFF (1)      
  ON (2)      
  Last State (3)      

6: Panic mode enable

Enables this switch to participate in panic mode

Property Value      
Configuration ID config_6_1      
Data Type INTEGER   Default Value 1
Options OFF (1)      
  ON (2)      

7: Dimmer Ramp Time

Time in seconds to reach desired level

Overview

The amount of time in seconds the switch will take to reach the desired dim level

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 0 to 255
Default Value 0

8: Kickstart / Rapid Start

Turn on or off rapid start feature

Overview

Ensures that LED / CFL bulbs turn on when the preset dim level is low.  Enabling this feature may cause the lights brightness to momentarily be bright when the switch is turned on before reducing in brightness to desired level

Property Value      
Configuration ID config_8_1      
Data Type INTEGER   Default Value 1
Options OFF (1)      
  ON (2)      

11: Minimum Dimmer Level

The minimum dim level the switch will allow

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 4 to 99
Default Value 4

12: Maximum Dimmer Level

The maximum dim level the switch will allow

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 4 to 99
Default Value 99

1: Group 1

Property Value
Configuration ID group_1
Data Type TEXT
Range to

255: Group 255

Overview

Life line to the controller

Property Value
Configuration ID group_255
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.