The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

DAS-102 Double relay Switch 2x1.7kW

This describes the Z-Wave device DAS-102, manufactured by Defaro with the thing type UID of defaro_das102_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

DAS-102 product image

The DAS-102 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

https://defaro.ru/index.php/support/instructions/70-das-102

Inclusion Information

  1. Put controller in inclusion mode.
  2. Power on device. It should be added automatically (using NWI).
  3. If not fast press add/remove button three times.

Exclusion Information

  1. Put controller in exclusion mode.
  2. Fast press add/remove button three times.
  3. Please note that all parameters except for parameters 15 & 16 will reset to their default state

Wakeup Information

Always woken.

Channels

The following table summarises the channels available for the DAS-102 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Switch 1 switch_binary1 Switch Switch
Switch 2 switch_binary2 Switch Switch

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Switch 2

Switch the power on and off.

The switch_binary2 channel supports the Switch item and is in the Switch category.

Device Configuration

The following table provides a summary of the 19 configuration parameters available in the DAS-102. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Load type Selects load type for dimmer
2 Relay closed interval For blink mode for both S1 and S2
3 Relay open interval For blink mode for both S1 and S2
4 S1 auto off delay Sets auto off delay for S1
5 S1 On delay Delay after ON command received
6 S1 smart delay Smart off delay for S1
7 S1 powerfail recovery Powerfail recovery mode for S1
8 All ON/OFF behaviour All ON/OFF behaviour
10 Relay S2 mode Relay S2 mode of operation
11 S2 auto off time Sets auto off time for S2
12 S2 turn on delay Sets turn on delay for S2
13 S2 smart delay Smart delay for S2
14 S2 powerfail recovery Powerfail recovery mode for S2
15 S1 button mode S1 button operation mode
16 S2 button mode S2 button operation mode
18 Smart delay Smart delay mode
50 Forced secure mode Forced secure mode
51 Secure send for S1 Send secure commands for S1
52 Secure send for S2 Send secure commands for S2
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Load type

Selects load type for dimmer

The following option values may be configured -:

Value Description
0 Normal
1 Reverse
2 Blink mode

The manufacturer defined default value is 3.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Relay closed interval

For blink mode for both S1 and S2 Sets relays ON state time in 1/10 of second, if Parameter 1 or 10 set to 3This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 65000 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_2_2 and is of type INTEGER.

Parameter 3: Relay open interval

For blink mode for both S1 and S2 Sets relays OFF state time in 1/10 of second, if Parameter 1 or 10 set to 3This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 65000 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_3_2 and is of type INTEGER.

Parameter 4: S1 auto off delay

Sets auto off delay for S1 Sets delay after which switch S1 will turn off in 1/10 sec. (0 - disable) The following option values may be configured, in addition to values in the range 0 to 65000 -:

Value Description
0 Disable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_4_2 and is of type INTEGER.

Parameter 5: S1 On delay

Delay after ON command received Sets time after which switch S1 will turn on after receiving ON command in 1/10 sec. (0 - disable feature) The following option values may be configured, in addition to values in the range 0 to 65000 -:

Value Description
0 Disable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_5_2 and is of type INTEGER.

Parameter 6: S1 smart delay

Smart off delay for S1 Sets time after which switch S1 will turn off after receiving OFF command in 1/10 sec.

Events to which this delay is applicable set in Parameter 18.

(0 - disable feature)This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured, in addition to values in the range 0 to 65000 -:

Value Description
0 Disable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_6_2 and is of type INTEGER.

Parameter 7: S1 powerfail recovery

Powerfail recovery mode for S1 Recovery behavior for S1

0 - restore (default)

1 - set to OFF state The following option values may be configured -:

Value Description
0 Restore previous state
1 Always set to OFF state

The manufacturer defined default value is 0 (Restore previous state).

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 8: All ON/OFF behaviour

All ON/OFF behaviour 0 - React on All ON/All OFF

1 - Ignore All ON/All OFF

2 - Ignore All ON/React on All OFF

3 - React on All ON/Ignore All OFF Values in the range 0 to 3 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 10: Relay S2 mode

Relay S2 mode of operation Sets S2 mode of operation:

0 - normal mode (ON-turn switch on, 1 - turn switch off) (default)

1 - reverse mode (ON-turn switch off, 1 - turn switch on)

2 - Blink mode (see parameters 2 and 3) The following option values may be configured -:

Value Description
0 Normal
1 Reverse
2 Blink

The manufacturer defined default value is 0 (Normal).

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 11: S2 auto off time

Sets auto off time for S2 Sets time after which switch S2 will turn off in 1/10 sec. (0 - disable) The following option values may be configured, in addition to values in the range 0 to 65000 -:

Value Description
0 Disable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_11_2 and is of type INTEGER.

Parameter 12: S2 turn on delay

Sets turn on delay for S2 Sets delay after which switch S1 will turn on after receiving ON command in 1/10 sec. (0 - disable) The following option values may be configured, in addition to values in the range 0 to 65000 -:

Value Description
0 Disable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_12_2 and is of type INTEGER.

Parameter 13: S2 smart delay

Smart delay for S2 Sets smart delay for S2 in 1/10sec (see Parameters 2,3,6 for description) (0-disable)This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured, in addition to values in the range 0 to 65000 -:

Value Description
0 Disable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_13_2 and is of type INTEGER.

Parameter 14: S2 powerfail recovery

Powerfail recovery mode for S2 Recovery behavior for S2

0 - restore (default)

1 - set to OFF state The following option values may be configured -:

Value Description
0 Restore state
1 Set to OFF

The manufacturer defined default value is 0 (Restore state).

This parameter has the configuration ID config_14_1 and is of type INTEGER.

Parameter 15: S1 button mode

S1 button operation mode Type of button connected to S1 switch The following option values may be configured -:

Value Description
0 Monostable (push button)
1 Bistable (switch)
2 Bistable (fixed switch)
3 Bistable (reversed fixed switch)

The manufacturer defined default value is 0 (Monostable (push button)).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 16: S2 button mode

S2 button operation mode Type of button connected to S2 switch The following option values may be configured -:

Value Description
0 Monostable (push button)
1 Bistable (switch button)
2 Bistable (fixed switch button)
3 Bistable (reversed fixed switch)

The manufacturer defined default value is 0 (Monostable (push button)).

This parameter has the configuration ID config_16_1 and is of type INTEGER.

Parameter 18: Smart delay

Smart delay mode 0 - implicit smart delay

1 - use smart delay for all devices NOT in Group 1. Also smart delay ignored for controller and button issued commands

2 - use smart delay for all devices IN Group 1. Also smart delay will be used for controller and button issued commandsThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 2 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_18_1 and is of type INTEGER.

Parameter 50: Forced secure mode

Forced secure mode 0 - accept non-secure commands

1 - accept only secure commandsThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:

Value Description
0 Accept non-secure commands
1 Accept only secure commands

The manufacturer defined default value is 0 (Accept non-secure commands).

This parameter has the configuration ID config_50_1 and is of type INTEGER.

Parameter 51: Secure send for S1

Send secure commands for S1 0 - Send non-secure commands to Group 2 (S1 associations)

1 - Send secure commands to Group 2 (S1 associations)This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:

Value Description
0 Non-secure
1 Secure

The manufacturer defined default value is 0 (Non-secure).

This parameter has the configuration ID config_51_1 and is of type INTEGER.

Parameter 52: Secure send for S2

Send secure commands for S2 0 - Send non-secure commands to Group 3 (S2 associations)

1 - Send secure commands to Group 3 (S2 associations)This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:

Value Description
0 Non-secure
1 Secure

The manufacturer defined default value is 0 (Non-secure).

This parameter has the configuration ID config_52_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The DAS-102 supports 3 association groups.

Group 1: State changes

State changes – general This group supports 3 nodes.

Group 2: Switch 1

Switch 1 ON/OFF associations This group supports 10 nodes.

Group 3: Switch 2

Switch 2 ON/OFF associations This group supports 10 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V0| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | | COMMAND_CLASS_SECURITY_V0| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 2

Command Class Comment
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.