The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ph-pse02 Multisound indoor siren (Zipato/Devolo)

This describes the Z-Wave device ph-pse02, manufactured by Devolo with the thing type UID of devolo_phpse02_00_000.

The device is in the category of Siren, defining Siren used by Alarm systems.

ph-pse02 product image

The ph-pse02 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

### NOTE ###

The XML used for adding this device to the database comes from the Devolo Home Control Alarmsiren (http://www.devolo.de/article/devolo-home-control-alarmsirene/). But it seems to be made by Zipato (https://www.zipato.com/product/multisound-indoor-siren).

### FEATURES ###

- Indoor multichannel siren that works with a a variety of Z-Wave networks/controllers, regardless of the manufacturer
- The new Z-Wave 500 series chip supports multichannel operationand higher data rates (9.6/40/100kbps)
- 110db sound level
- 6 sounds: Door Chime, Bi Bi Arm/Disarm, Intruder alarm, Ambulance, Police car
- Higher output power enhances communication range(+6dBm output power as compared to -2.5dBm 300 series)
- DC or Li-ion battery power (over 24 hours of battery life)
- Battery overcharge protection
- Very low power consumption
- Over-the-air firmware update
- Easy to install in EU/China/Taiwan wall sockets
- Tamperproof protection

### TECHNICAL SPECIFICATIONS ###

PROTOCOL: Z-Wave Plus

POWER
- DC 5V, Li-Ion battery (optional)
- BATTERY CAPACITY 1150mAh

OPERATING CONDITIONS:
- OPERATING VOLTAGE 3.7V
- OPERATING CURRENT 150 mA
- OPERATION TEMPERATURE -10°C ~ 40°C

RANGE
- Minimum 30 meters indoor
- 70 meters outdoor (meant for indoor use only)

DIMENSIONS
- DEVICE DIMENSIONS 110 x 110 x 22 mm
- DEVICE WEIGHT 113g
- PACKAGE DIMENSIONS 117 x 50 x 117 mm
- PACKAGE WEIGHT 217g

FREQUENCY

ph-pse02.au 921.42 MHz (AU)
ph-pse02.eu 868.42 MHz (EU)
ph-pse02.in 865.20 MHz (IN)
ph-pse02.is 916.02 MHz (IS)
ph-pse02.ru 869.02 MHz (RU)
ph-pse02.us 908.42 MHz (US)

Source: https://www.zipato.com/product/multisound-indoor-siren

Channels

The following table summarises the channels available for the ph-pse02 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Binary Sensor sensor_binary Door Switch
Alarm (burglar) alarm_burglar Door Switch
Alarm (general) alarm_general Door Switch
Start Sound notification_send   Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Alarm (burglar)

Indicates if the burglar alarm is triggered.

The alarm_burglar channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Alarm (general)

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Start Sound

Notification

Event

Sound

event1 Smokealarm (0x01)

0x01 ~ 0xFF

fire alert

event2 Accesscontrol (0x06)

Window/Door open (0x16)

door chime

event7 Accesscontrol (0x06)

Activate alarm system (0x03)

2x beep

event8 Accesscontrol (0x06)

Deactivate alarm system (0x04)

1x beep

event3 Homesecurity (0x07)

0x01 ~ 0xFF

emergency

sound event4 Emergency (0x0A)

Contact police (0x01)

policecar

sound

event5 Emergency (0x0A)

Contact fire department (0x02)

fire engine sound

event6 Emergency (0x0A)

Contact ambulance (0x03)

ambulance

sound

event9 Emergency (0x0A) Notification (0xFE)

silent alarm (no sound, flashing LED)

Sends a notification.

The notification_send channel supports the Number item.

Device Configuration

The following table provides a summary of the 3 configuration parameters available in the ph-pse02. Detailed information on each parameter can be found in the sections below.

Param Name Description
7 Costumer Function NotificationReport/BinaryReport
29 Disable Alarm Disable the alarm function.
31 Alarm Duration Play alarm sound duration.

Parameter 7: Costumer Function

NotificationReport/BinaryReport Notification Type,

0: Using Notification Report.

1: Using Sensor Binary Report.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_7_4 and is of type INTEGER.

Parameter 29: Disable Alarm

Disable the alarm function. Disable the alarm function.

1: Disable Alarm,

0: Enable Alarm.

Caution: After the power up, this configuration is always 0. Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_29_4 and is of type INTEGER.

Parameter 31: Alarm Duration

Play alarm sound duration. Play alarm sound duration, 1 tick is 30 seconds.

Default is 3 minutes, maximum is 63.5 minutes.

0 means never auto stop. Values in the range 0 to 127 may be set.

The manufacturer defined default value is 6.

This parameter has the configuration ID config_31_4_0000000C and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ph-pse02 supports 1 association group.

Group 1: Report Message

Report Message, e.g. tamper alarm This group supports 8 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_MULTILEVEL_V0  
COMMAND_CLASS_SENSOR_BINARY_V2  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V4  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.