The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

PST02-1B Multisensor

This describes the Z-Wave device PST02-1B, manufactured by Devolo with the thing type UID of devolo_pst021b_00_000.

PST02-1B product image

The PST02-1B supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The PST02-1B does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the PST02-1B -:

Channel Channel Id Category Item Type
Binary Sensor sensor_binary Door Switch
Sensor (temperature) sensor_temperature Temperature Number
Sensor (luminance) sensor_luminance Temperature Number
Battery Level battery-level Battery Number

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Sensor (temperature)

Indicates the current temperature.

The sensor_temperature channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Sensor (luminance)

Indicates the current light reading.

The sensor_luminance channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 11 configuration parameters available in the PST02-1B. Detailed information on each parameter can be found in the sections below.

Param Name Description
2 Basic Set Level -1 -> 0xFF(-1) turns on the light. 1 - 100 -> For dimmers 1 to 100 means the light strength
3 PIR Sensitivity parameter to set the Sensitivity for the PIR (Passiv Infrared Sensor) 0 -> 0 means disable the PIR motion; 1 - 99 -> 1 means the lowest sensitivity, 99 means the highest sensitivity
4 Light Threshold Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light 0 -> 0 means turn off illumination detected function And never turn on the
5 Operation Mode Bit 0: 1 means security mode; 0 means home automation mode. Bit 1: 1 means enable test mode; 0 means disable test mode. Notice: Bit0 and Bit1 will effect when the DIP Switch setting to program mode. If Bit1 is enabled, the Bit0 is useless. Bit 2: Disable
6 Multi-Sensor Function Switch Bit 0: Disable magnetic integrate illumination. Bit 1: Disable PIR integrate Illumination. Bit 2: Disable magnetic integrate PIR (Default is Disable) Bit 3: When Bit2 is 0 (Enable), the device is install in the same room with the light? 0: In the same roo
7 Customer Function Parameter to set the Customer Function. Bit 0: Reserved. Bit 1: Enable sending motion OFF report. 0: Disable, 1: Enable. Note: Depends on the Bit4, 0: Report Notification CC, Type: 0x07, Event: 0xFE 1: Sensor Binary Report,
8 PIR Re-Detect Interval Time In the security mode, after the PIR motion detected, setting the re-detect time 3 8 sec - 127 8 sec -> 8 seconds per tick, and minimum time is 24 seconds, default tick is 3 (24 seconds).
9 Turn Off Light Time After turn on the light, setting the delay time to turn off the light when the PIR motion is not detected 4 8 sec - 127 8 sec -> 8 seconds per tick, and minimum time is 32 seconds, default tick is 4 (32 seconds)
10 Auto Report Battery Time interval time for auto report the battery level 1 30 min - 127 30 min -> 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours)
12 Auto Report Illumination Time interval time for auto report the illumination state 1 30 min - 127 30 min -> 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours)
13 Auto Report Temperature Time Interval time for auto report the temperature state 1 30 min - 127 30 min -> 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours)
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 2: Basic Set Level

-1 -> 0xFF(-1) turns on the light. 1 - 100 -> For dimmers 1 to 100 means the light strength

Values in the range -1 to 100 may be set.

The manufacturer defined default value is -1.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: PIR Sensitivity

parameter to set the Sensitivity for the PIR (Passiv Infrared Sensor) 0 -> 0 means disable the PIR motion; 1 - 99 -> 1 means the lowest sensitivity, 99 means the highest sensitivity

Values in the range 0 to 99 may be set.

The manufacturer defined default value is 70.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Light Threshold

Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light 0 -> 0 means turn off illumination detected function And never turn on the

Values in the range 0 to 100 may be set.

The manufacturer defined default value is 100.

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Operation Mode

Bit 0: 1 means security mode; 0 means home automation mode. Bit 1: 1 means enable test mode; 0 means disable test mode. Notice: Bit0 and Bit1 will effect when the DIP Switch setting to program mode. If Bit1 is enabled, the Bit0 is useless. Bit 2: Disable

Values in the range 0 to 127 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 6: Multi-Sensor Function Switch

Bit 0: Disable magnetic integrate illumination. Bit 1: Disable PIR integrate Illumination. Bit 2: Disable magnetic integrate PIR (Default is Disable) Bit 3: When Bit2 is 0 (Enable), the device is install in the same room with the light? 0: In the same roo

Values in the range 0 to 127 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_6_1 and is of type INTEGER.

Parameter 7: Customer Function

Parameter to set the Customer Function. Bit 0: Reserved. Bit 1: Enable sending motion OFF report. 0: Disable, 1: Enable. Note: Depends on the Bit4, 0: Report Notification CC, Type: 0x07, Event: 0xFE 1: Sensor Binary Report,

The following option values may be configured, in addition to values in the range 0 to 127 -:

Value Description
22 Preset: PIR Super Sensitivity and Binary Report and Motion Off Report

The manufacturer defined default value is 0.

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 8: PIR Re-Detect Interval Time

In the security mode, after the PIR motion detected, setting the re-detect time 3 8 sec - 127 8 sec -> 8 seconds per tick, and minimum time is 24 seconds, default tick is 3 (24 seconds).

Values in the range 3 to 127 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: Turn Off Light Time

After turn on the light, setting the delay time to turn off the light when the PIR motion is not detected 4 8 sec - 127 8 sec -> 8 seconds per tick, and minimum time is 32 seconds, default tick is 4 (32 seconds)

Values in the range 4 to 127 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_9_1 and is of type INTEGER.

Parameter 10: Auto Report Battery Time

interval time for auto report the battery level 1 30 min - 127 30 min -> 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours)

Values in the range 1 to 127 may be set.

The manufacturer defined default value is 12.

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 12: Auto Report Illumination Time

interval time for auto report the illumination state 1 30 min - 127 30 min -> 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours)

Values in the range 1 to 127 may be set.

The manufacturer defined default value is 12.

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 13: Auto Report Temperature Time

Interval time for auto report the temperature state 1 30 min - 127 30 min -> 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours)

Values in the range 1 to 127 may be set.

The manufacturer defined default value is 12.

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The PST02-1B supports 2 association groups.

Group 1: Reports

This group supports 7 nodes.

Group 2: Light Control

This group supports 7 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SENSOR_BINARY_V2  
COMMAND_CLASS_SENSOR_MULTILEVEL_V5  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.