ph-pse02 Multisound indoor siren (Zipato/Devolo)

This describes the Z-Wave device ph-pse02, manufactured by Devolo with the thing type UID of devolo_phpse02_00_000.

Multisound indoor siren (Zipato/Devolo)

Overview

### NOTE ###

The XML used for adding this device to the database comes from the Devolo Home Control Alarmsiren (http://www.devolo.de/article/devolo-home-control-alarmsirene/). But it seems to be made by Zipato (https://www.zipato.com/product/multisound-indoor-siren).

### FEATURES ###

- Indoor multichannel siren that works with a a variety of Z-Wave networks/controllers, regardless of the manufacturer
- The new Z-Wave 500 series chip supports multichannel operationand higher data rates (9.6/40/100kbps)
- 110db sound level
- 6 sounds: Door Chime, Bi Bi Arm/Disarm, Intruder alarm, Ambulance, Police car
- Higher output power enhances communication range(+6dBm output power as compared to -2.5dBm 300 series)
- DC or Li-ion battery power (over 24 hours of battery life)
- Battery overcharge protection
- Very low power consumption
- Over-the-air firmware update
- Easy to install in EU/China/Taiwan wall sockets
- Tamperproof protection

### TECHNICAL SPECIFICATIONS ###

PROTOCOL: Z-Wave Plus

POWER
- DC 5V, Li-Ion battery (optional)
- BATTERY CAPACITY 1150mAh

OPERATING CONDITIONS:
- OPERATING VOLTAGE 3.7V
- OPERATING CURRENT 150 mA
- OPERATION TEMPERATURE -10°C ~ 40°C

RANGE
- Minimum 30 meters indoor
- 70 meters outdoor (meant for indoor use only)

DIMENSIONS
- DEVICE  DIMENSIONS 110 x 110 x 22 mm
- DEVICE WEIGHT 113g
- PACKAGE DIMENSIONS 117 x 50 x 117 mm
- PACKAGE WEIGHT 217g

FREQUENCY

    ph-pse02.au 921.42 MHz (AU)
    ph-pse02.eu 868.42 MHz (EU)
    ph-pse02.in 865.20 MHz (IN)
    ph-pse02.is 916.02 MHz (IS)
    ph-pse02.ru 869.02 MHz (RU)
    ph-pse02.us 908.42 MHz (US)

Source: https://www.zipato.com/product/multisound-indoor-siren

Channels

The following table summarises the channels available for the ph-pse02 Multisound indoor siren (Zipato/Devolo).

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Binary Sensor sensor_binary sensor_binary Door Switch
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
Alarm (general) alarm_general alarm_general Door Switch
Start Sound notification_send notification_send   Number

Device Configuration

The following table provides a summary of the configuration parameters available in the ph-pse02 Multisound indoor siren (Zipato/Devolo). Detailed information on each parameter can be found below.

Parameter Description
7: Costumer Function NotificationReport/BinaryReport
29: Disable Alarm Disable the alarm function.
31: Alarm Duration Play alarm sound duration.
1: Report Message Report Message, e.g. tamper alarm

7: Costumer Function

NotificationReport/BinaryReport

Overview

Notification Type,

0: Using Notification Report.

1: Using Sensor Binary Report.

Property Value
Configuration ID config_7_4
Data Type INTEGER
Range 0 to 65535
Default Value 4

29: Disable Alarm

Disable the alarm function.

Overview

Disable the alarm function.

1: Disable Alarm,

0: Enable Alarm.

Caution: After the power up, this configuration is always 0.

Property Value
Configuration ID config_29_4
Data Type INTEGER
Range 0 to 1
Default Value 0

31: Alarm Duration

Play alarm sound duration.

Overview

Play alarm sound duration, 1 tick is 30 seconds.

Default is 3 minutes, maximum is 63.5 minutes.

0 means never auto stop.

Property Value
Configuration ID config_31_4_0000000C
Data Type INTEGER
Range 0 to 127
Default Value 6

1: Report Message

Report Message, e.g. tamper alarm

Overview

Notice: The device supports 1 group.

The group 1 is for receiving the report message, like tamper event. And the group 8 nodes maximum

Property Value
Configuration ID group_1
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.