The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

heatapp! floor heatapp! floor is a controller for thermal actuators in underfloor heating installations and is part of the heatapp! system, providing individual circ

This describes the Z-Wave device heatapp! floor, manufactured by EbV with the thing type UID of ebv_heatappfloor_00_000.

The device is in the category of Radiator Control, defining Controls on radiators used to heat up rooms.

heatapp! floor product image

The heatapp! floor supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

Information at the z-wave alliance product cataloge: https://products.z-wavealliance.org/products/1249

Inclusion Information

Press the learn key (10) for 2 seconds that will start the inclusion process on the device.

Exclusion Information

Press the learn key (10) for 2 seconds that will start the exclusion process on the device.

Channels

The following table summarises the channels available for the heatapp! floor -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Switch 1 switch_binary1 Switch Switch
Switch 2 switch_binary2 Switch Switch
Switch 3 switch_binary3 Switch Switch
Switch 4 switch_binary4 Switch Switch
Switch 5 switch_binary5 Switch Switch
Switch 6 switch_binary6 Switch Switch
Switch 7 switch_binary7 Switch Switch
Switch 8 switch_binary8 Switch Switch

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Switch 2

Switch the power on and off.

The switch_binary2 channel supports the Switch item and is in the Switch category.

Switch 3

Switch the power on and off.

The switch_binary3 channel supports the Switch item and is in the Switch category.

Switch 4

Switch the power on and off.

The switch_binary4 channel supports the Switch item and is in the Switch category.

Switch 5

Switch the power on and off.

The switch_binary5 channel supports the Switch item and is in the Switch category.

Switch 6

Switch the power on and off.

The switch_binary6 channel supports the Switch item and is in the Switch category.

Switch 7

Switch the power on and off.

The switch_binary7 channel supports the Switch item and is in the Switch category.

Switch 8

Switch the power on and off.

The switch_binary8 channel supports the Switch item and is in the Switch category.

Device Configuration

The following table provides a summary of the 2 configuration parameters available in the heatapp! floor. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Missing Radio Link time Maximum time device will wait for reconnection before going to emergency mode (All switches ON).
2 Relay type 0 normal open, 1 normal close, 2 switching
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Maximum time device will wait for reconnection before going to emergency mode (All switches ON). It is maximum time device will wait for reconnection before it going ot emergency mode (All switches ON). It is possible to set in the range of 10min to 4hours. Default value is 30min, only 1 Byte Values in the range 10 to 240 may be set.

The manufacturer defined default value is 30.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Relay type

0 normal open, 1 normal close, 2 switching Configuaration parameter2 relay type. Default relay type is normal open, only 1 Byte. 0 normal open, 1 normal close, 2 switching The following option values may be configured -:

Value Description
0 Normal open
1 Normal close
2 Switching

The manufacturer defined default value is 0 (Normal open).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_VERSION_V2| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 2

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 3

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 4

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 5

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 6

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 7

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 8

Command Class Comment
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.