The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

AD147 Z-Wave Dimmer Plug

This describes the Z-Wave device AD147, manufactured by Everspring with the thing type UID of everspring_ad147_00_000.

The AD147 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the AD147 -:

Channel Channel Id Category Item Type
Dimmer switch_dimmer DimmableLight Dimmer
Alarm (general) alarm_general Door Switch

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Alarm (general)

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Device Configuration

The following table provides a summary of the 4 configuration parameters available in the AD147. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Basic Set Command value Basic Set Command value
2 Delaying Time to report to Group 1 The delaying time to report to Group 1
3 Remember the last status Remember the last status
4 Output mode setting: Dimming, On/Off Output mode setting: Dimming, On/Off
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Basic Set Command value

Basic Set Command value

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_1_2 and is of type INTEGER.

Parameter 2: Delaying Time to report to Group 1

The delaying time to report to Group 1

Values in the range 3 to 25 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Remember the last status

Remember the last status 1 = Remember

0 = Do not remember Values in the range 0 to 1 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Output mode setting: Dimming, On/Off

Output mode setting: Dimming, On/Off 0 = Dimming

1 = On/off Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The AD147 supports 2 association groups.

Group 1: Lifeline

Provides reports This group supports 1 nodes.

Group 2: On/Off control

Basic Set This group supports 4 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V1  
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.