VMZ Solar z-wave plus Awning Blind z-wave plus version

This describes the Z-Wave device VMZ Solar z-wave plus, manufactured by Fakro with the thing type UID of fakro_vmzsolarplus_00_000.

Awning Blind z-wave plus version

Channels

The following table summarises the channels available for the VMZ Solar z-wave plus Awning Blind z-wave plus version.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Blinds control blinds_control blinds_control Blinds Rollershutter
Alarm (power) alarm_power alarm_power Door Switch
  battery-level system.battery-level    

Blinds control

Invert control

Invert the blinds control

Property Value      
Configuration ID config_invert_control      
Data Type BOOLEAN   Default Value false
Options Yes (true)      
  No (false)      

Invert percentage value

Invert the blinds percentage value

Property Value      
Configuration ID config_invert_percent      
Data Type BOOLEAN   Default Value false
Options Yes (true)      
  No (false)      

Step duration

Sets the dim rate speed
Values from 1 to 127 are defined in seconds, while values from 128 to 254 are defined in minutes.

Property Value      
Configuration ID config_duration      
Data Type INTEGER      
Range 1 to 254   Default Value 255
Options Device Default (255)      
  Change Instantly (0)      

Device Configuration

The following table provides a summary of the configuration parameters available in the VMZ Solar z-wave plus Awning Blind z-wave plus version. Detailed information on each parameter can be found below.

Parameter Description
1: operating mode operating mode
2: winter mode Summer/Winter mode
3: Delay time delay to auto shade
4: Level of sensitivity for day Level of insolation to open/close the shades
5: Temperature Temperature
6: STM active STM AutoShade active
13: Restore last position Restore last position
17: Insolation level Current on autoshade solar panel
21: Motor current Motor current
77: CLOSE current CLOSE current
78: OPEN current OPEN current
79: CLOSE overload current CLOSE overload current
80: OPEN overload current OPEN overload current
99: Restore default config values Restore default config values
100: Autoexclude Autoexclude
1: Lifeline  
2: BasicRepeat  
3: MultilevelRepeat  
4: BasicControl  

1: operating mode

operating mode

Overview

Operating mode. Available values:

0 - manual

1 - semiauto: goes down automatically but does not go up.

2 - auto

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 0
Options manual (0)      
  semiauto (1)      
  auto (2)      

2: winter mode

Summer/Winter mode

Overview

summer mode: go down if sun shines and go up if it is cloudy

winter mode: if temperature is below 0 deg C and sun shines then go up if it is cloudy go down. If temperature is above 0 deg C works as a summer mode

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 1
Options summer mode only (1)      
  winter mode (2)      

3: Delay time

delay to auto shade

Overview

Delay time in minutes after which the shade is open or closed in auto mode

Property Value
Configuration ID config_3_1
Data Type INTEGER
Range 0 to 30
Default Value 0

4: Level of sensitivity for day

Level of insolation to open/close the shades

Overview

Level of insolation in mA to open/close the shades in the auto mode

Property Value
Configuration ID config_4_1
Data Type INTEGER
Range 3 to 100
Default Value 3

5: Temperature

Temperature

Overview

T[oC] = x minus 50

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 0 to 255
Default Value 0

6: STM active

STM AutoShade active

Property Value      
Configuration ID config_6_1      
Data Type INTEGER   Default Value 0
Options no (0)      
  yes (1)      

13: Restore last position

Restore last position

Overview

Restore last position or always go down till the end.

Property Value      
Configuration ID config_13_1      
Data Type INTEGER   Default Value 1
Options go down (1)      
  restore last position (2)      

17: Insolation level

Current on autoshade solar panel

Overview

Current from autoshade solar panel for loading battery: 0 - 255 mA

Property Value
Configuration ID config_17_1
Data Type INTEGER
Range 0 to 255
Default Value 0

21: Motor current

Motor current

Overview

Current used by motor: 10[mA] - 2,55[A]

Property Value
Configuration ID config_21_1
Data Type INTEGER
Range 0 to 255
Default Value 0

77: CLOSE current

CLOSE current

Overview

CLOSE current: 1[mA] - 255[mA]

Property Value
Configuration ID config_77_1
Data Type INTEGER
Range 1 to 255
Default Value 1

78: OPEN current

OPEN current

Overview

OPEN current: 1[mA] - 255[mA]

Property Value
Configuration ID config_78_1
Data Type INTEGER
Range 1 to 255
Default Value 1

79: CLOSE overload current

CLOSE overload current

Overview

CLOSE overload current: 10[mA] - 2,55[A]

Property Value
Configuration ID config_79_1
Data Type INTEGER
Range 0 to 255
Default Value 0

80: OPEN overload current

OPEN overload current

Overview

OPEN overload current: 10[mA] - 2,55[A]

Property Value
Configuration ID config_80_1
Data Type INTEGER
Range 0 to 255
Default Value 0

99: Restore default config values

Restore default config values

Overview

Restore default config values.

Property Value      
Configuration ID config_99_1      
Data Type INTEGER   Default Value 2
Options restore default config values (1)      
  user values (2)      

100: Autoexclude

Autoexclude

Property Value      
Configuration ID config_100_1      
Data Type INTEGER   Default Value 1
Options off (1)      
  on (2)      

1: Lifeline

Overview
BATTERY ALARM DEVICE\_RESET\_LOCALLY BASIC

 

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: BasicRepeat

Overview
BASIC
Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: MultilevelRepeat

Overview
SWITCH\_MULTILEVEL
Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: BasicControl

Overview
BASIC
Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.