The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

FGGC001 Fibaro Swipe Scene Controller

This describes the Z-Wave device FGGC001, manufactured by Fibargroup with the thing type UID of fibaro_fggc001_00_000.

FGGC001 product image

The FGGC001 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The FGGC001 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the FGGC001 -:

Channel Channel Id Category Item Type
Scene Number scene_number   Number
Battery Level battery-level Battery Number

Scene Number

Triggers when a scene button is pressed.

The scene_number channel supports the Number item.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 26 configuration parameters available in the FGGC001. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Device Orientation Parameter determines orientation of the Swipe in relation to its default position.
2 Buzzer - acoustic signal settings Acoustic signalling of gestures detection.
3 LED diode - visual indicator settings Visual indication of gestures detection
4 Buzzer - signalling result of gesture recognition Acoustic signalling of gesture recognition result (using the built-in buzzer).
5 Powering mode - interval of updating the current mode This parameter determines how often the device checks if the USB power supply is connected and updates powering mode if needed.
6 Power saving mode (battery mode) This parameter determines operation of gesture detection when battery powered.
7 Hold gesture to enter the menu This parameter allows to choose if the menu can be entered using the Hold gesture.
10 Scenes sent to the controller Defines which actions result in sending scenes to 1st “Lifeline” group.
11 Associations in Z-Wave network security mode Parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st “Lifeline” association group.
12 Control mode of 2nd - 5th “Flick UP/DOWN/LEFT/RIGHT” association groups and scenes Parameter allows to choose control mode for 2nd-5th groups and scenes.
13 Rate of smooth level control Parameter allows to choose how long the hand has to be held near the center of the pad after “AirWheel” gesture for the associated devices to reach their maximum/minimum level.
20 SWITCH ON control frame value for FLICK UP gesture This parameter allows to set value sent in SWITCH ON command frame to the association group.
21 SWITCH OFF control frame value for FLICK UP gesture This parameter allows to set value sent in SWITCH OFF command frame to the association group.
22 SWITCH ON control frame value for FLICK DOWN gesture This parameter allows to set value sent in SWITCH ON command frame to the association group.
23 SWITCH OFF control frame value for FLICK DOWN gesture This parameter allows to set value sent in SWITCH OFF command frame to the association group.
24 SWITCH ON control frame value for FLICK LEFT gesture This parameter allows to set value sent in SWITCH ON command frame to the association group.
25 SWITCH OFF control frame value for FLICK LEFT gesture This parameter allows to set value sent in SWITCH OFF command frame to the association group.
26 SWITCH ON control frame value for FLICK RIGHT gesture This parameter allows to set value sent in SWITCH ON command frame to the association group.
27 SWITCH OFF control frame value for FLICK RIGHT gesture This parameter allows to set value sent in SWITCH OFF command frame to the association group.
30 Sequence learning mode Parameter activated by the main Z-Wave controller. Change its value to launch sequence learning procedure for the desired slot.
31 1st gestures sequence (SLOT 1) Value containing sequence of gestures.
32 2nd gestures sequence (SLOT 2) Value containing sequence of gestures.
33 3rd gestures sequence (SLOT 3) Value containing sequence of gestures.
34 4th gestures sequence (SLOT 4) Value containing sequence of gestures.
35 5th gestures sequence (SLOT 5) Value containing sequence of gestures.
36 6th gestures sequence (SLOT 6) Value containing sequence of gestures.
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 1: Device Orientation

Parameter determines orientation of the Swipe in relation to its default position.

The following option values may be configured -:

Value Description
0 Default Orientation
1 180° rotation
2 90° clockwise rotation
3 90° counter-clockwise rotation

The manufacturer defined default value is 0 (Default Orientation).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Buzzer - acoustic signal settings

Acoustic signalling of gestures detection.

The following option values may be configured -:

Value Description
0 Gestures detection is not signalled
1 Gestures detection is signalled

The manufacturer defined default value is 1 (Gestures detection is signalled).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: LED diode - visual indicator settings

Visual indication of gestures detection

The following option values may be configured -:

Value Description
0 Gestures detection is not indicated
1 Gestures detection is indicated

The manufacturer defined default value is 0 (Gestures detection is not indicated).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Buzzer - signalling result of gesture recognition

Acoustic signalling of gesture recognition result (using the built-in buzzer). Parameter 4 is relevant only if parameter 2 is set to 1. The following option values may be configured -:

Value Description
1 Only successful recognition is signalled
2 Only failed recognition is signalled
3 Successful and failed recognition is signalled

The manufacturer defined default value is 3 (Successful and failed recognition is signalled).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Powering mode - interval of updating the current mode

This parameter determines how often the device checks if the USB power supply is connected and updates powering mode if needed.

The following option values may be configured, in addition to values in the range 0 to 1080 -:

Value Description
0 Powering mode is not updated
1 Time interval (in minutes)

The manufacturer defined default value is 4.

This parameter has the configuration ID config_5_2 and is of type INTEGER.

Parameter 6: Power saving mode (battery mode)

This parameter determines operation of gesture detection when battery powered. When Standby Mode is selected, hold gesture must be performed to exit power saving mode and reactivate normal gesture recognition. The device in Standby Mode consumes the least battery life.

When Simple Mode mode is selected, gesture recognition is always active, but only slowly performed gestures will be recognized properly (high battery consumption). The following option values may be configured -:

Value Description
0 Standby mode
1 Simple mode
2 Swipe does not enter power saving mode

The manufacturer defined default value is 0 (Standby mode).

This parameter has the configuration ID config_6_1 and is of type INTEGER.

Parameter 7: Hold gesture to enter the menu

This parameter allows to choose if the menu can be entered using the Hold gesture. After disabling the Hold gesture in parameter 7, menu can be entered by using the B-button only!This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:

Value Description
0 Hold gesture to enter the menu enabled
1 Hold gesture to enter the menu disabled

The manufacturer defined default value is 0 (Hold gesture to enter the menu enabled).

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 10: Scenes sent to the controller

Defines which actions result in sending scenes to 1st “Lifeline” group. Parameter 10 values may be combined, e.g. 1+2=3 means that scenes for flick UP and DOWN are enabled. The following option values may be configured, in addition to values in the range 1 to 63 -:

Value Description
1 Scenes for flick UP gesture enabled
2 Scenes for flick DOWN gesture enabled
4 Scenes for flick LEFT gesture enabled
8 Scenes for flick RIGHT gesture enabled
16 Scenes for clockwise circular gesture enabled
32 Scenes for counter-clockwise circular gesture enabled
63 All commands enabled

The manufacturer defined default value is 15.

This parameter has the configuration ID config_10_1 and is of type INTEGER. This is a read only parameter.

Parameter 11: Associations in Z-Wave network security mode

Parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st “Lifeline” association group. Parameter 11 values may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure. The following option values may be configured, in addition to values in the range 1 to 31 -:

Value Description
1 2nd group ”Flick UP” sent as secure
2 3rd group ”Flick DOWN” sent as secure
4 4th group “Flick LEFT” sent as secure
8 5th group “Flick RIGHT” sent as secure
16 6th group “Circular AirWheel” sent as secure

The manufacturer defined default value is 31.

This parameter has the configuration ID config_11_1 and is of type INTEGER.

Parameter 12: Control mode of 2nd - 5th “Flick UP/DOWN/LEFT/RIGHT” association groups and scenes

Parameter allows to choose control mode for 2nd-5th groups and scenes. By default, Toggle Mode is active, meaning that a single flick turns ON the group and the same flick turns it OFF, doubled flicks are inactive.

After disabling Toggle Mode a single flick will turn the device ON and the same flick doubled will turn it OFF.

Parameter 12 values may be combined, e.g. 1+2=3 means that 2nd & 3rd group are selected.

N.B. Disabling Toggle Mode will introduce delay when performing single gestures. The following option values may be configured, in addition to values in the range 1 to 15 -:

Value Description
1 Toggle Mode enabled for 2nd association group
2 Toggle Mode enabled for 3rd association group
4 Toggle Mode enabled for 4th association group
8 Toggle Mode enabled for 5th association group

The manufacturer defined default value is 15.

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 13: Rate of smooth level control

Parameter allows to choose how long the hand has to be held near the center of the pad after “AirWheel” gesture for the associated devices to reach their maximum/minimum level. Available settings:

0-10 - duration in seconds

255 - default settings of controlled devices Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_13_2 and is of type INTEGER.

Parameter 20: SWITCH ON control frame value for FLICK UP gesture

This parameter allows to set value sent in SWITCH ON command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_20_2 and is of type INTEGER.

Parameter 21: SWITCH OFF control frame value for FLICK UP gesture

This parameter allows to set value sent in SWITCH OFF command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_21_2 and is of type INTEGER.

Parameter 22: SWITCH ON control frame value for FLICK DOWN gesture

This parameter allows to set value sent in SWITCH ON command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_22_2 and is of type INTEGER.

Parameter 23: SWITCH OFF control frame value for FLICK DOWN gesture

This parameter allows to set value sent in SWITCH OFF command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_23_2 and is of type INTEGER.

Parameter 24: SWITCH ON control frame value for FLICK LEFT gesture

This parameter allows to set value sent in SWITCH ON command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_24_2 and is of type INTEGER.

Parameter 25: SWITCH OFF control frame value for FLICK LEFT gesture

This parameter allows to set value sent in SWITCH OFF command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_25_2 and is of type INTEGER.

Parameter 26: SWITCH ON control frame value for FLICK RIGHT gesture

This parameter allows to set value sent in SWITCH ON command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_26_2 and is of type INTEGER.

Parameter 27: SWITCH OFF control frame value for FLICK RIGHT gesture

This parameter allows to set value sent in SWITCH OFF command frame to the association group. Commands sent to association group for turn ON/OFF can be adjusted in parameters 20-27.

0 - turning off associated devices

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them onThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_27_2 and is of type INTEGER.

Parameter 30: Sequence learning mode

Parameter activated by the main Z-Wave controller. Change its value to launch sequence learning procedure for the desired slot. 0 - learning mode disabled

1-6 - launch sequence learning for selected slot

N.B. Sequences do not allow to use same gestures next to each otherThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 6 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_30_1 and is of type INTEGER.

Parameter 31: 1st gestures sequence (SLOT 1)

Value containing sequence of gestures. User can create sequences of two or three gestures to expand number of possible actions. Every sequence is saved in its advanced parameter (no. 31-36) with 16 bits, every basic gesture is identified with 4 bits.

Gesture Value Empty 0 ^ 1 v 2 < 3 > 4 #### Rules of creating sequences:

• Maximum of six sequences can be created.

• Each sequence must be unique.

• Sequence can consist of two or three basic gestures (left, right, up

or down).

• Two identical gestures cannot be used next to each other

To manually create or edit a sequence slot:

1. Calculate new value of parameter using table and formula:

Value of parameter = 256 * Value of first gesture + 16 * Value of second gesture + Value of third gesture

2. Change the value of corresponding parameter (parameters 31 to 36 for slots 1 to 6).

N.B. Setting parameter to 0 will delete the sequence.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1076 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_31_2 and is of type INTEGER.

Parameter 32: 2nd gestures sequence (SLOT 2)

Value containing sequence of gestures. User can create sequences of two or three gestures to expand number of possible actions. Every sequence is saved in its advanced parameter (no. 31-36) with 16 bits, every basic gesture is identified with 4 bits.

Gesture Value

Empty 0

^ 1

v 2

< 3

> 4

Rules of creating sequences:

• Maximum of six sequences can be created.

• Each sequence must be unique.

• Sequence can consist of two or three basic gestures (left, right, up

or down).

• Two identical gestures cannot be used next to each other

To manually create or edit a sequence slot:

1. Calculate new value of parameter using table and formula:

Value of parameter = 256 * Value of first gesture + 16 * Value of second gesture + Value of third gesture

2. Change the value of corresponding parameter (parameters 31 to 36 for slots 1 to 6).

N.B. Setting parameter to 0 will delete the sequence.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1076 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_32_2 and is of type INTEGER.

Parameter 33: 3rd gestures sequence (SLOT 3)

Value containing sequence of gestures. User can create sequences of two or three gestures to expand number of possible actions. Every sequence is saved in its advanced parameter (no. 31-36) with 16 bits, every basic gesture is identified with 4 bits.

Gesture Value

Empty 0

^ 1

v 2

< 3

> 4

Rules of creating sequences:

• Maximum of six sequences can be created.

• Each sequence must be unique.

• Sequence can consist of two or three basic gestures (left, right, up

or down).

• Two identical gestures cannot be used next to each other

To manually create or edit a sequence slot:

1. Calculate new value of parameter using table and formula:

Value of parameter = 256 * Value of first gesture + 16 * Value of second gesture + Value of third gesture

2. Change the value of corresponding parameter (parameters 31 to 36 for slots 1 to 6).

N.B. Setting parameter to 0 will delete the sequence.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1076 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_33_2 and is of type INTEGER.

Parameter 34: 4th gestures sequence (SLOT 4)

Value containing sequence of gestures. User can create sequences of two or three gestures to expand number of possible actions. Every sequence is saved in its advanced parameter (no. 31-36) with 16 bits, every basic gesture is identified with 4 bits.

Gesture Value

Empty 0

^ 1

v 2

< 3

> 4

Rules of creating sequences:

• Maximum of six sequences can be created.

• Each sequence must be unique.

• Sequence can consist of two or three basic gestures (left, right, up

or down).

• Two identical gestures cannot be used next to each other

To manually create or edit a sequence slot:

1. Calculate new value of parameter using table and formula:

Value of parameter = 256 * Value of first gesture + 16 * Value of second gesture + Value of third gesture

2. Change the value of corresponding parameter (parameters 31 to 36 for slots 1 to 6).

N.B. Setting parameter to 0 will delete the sequence.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1076 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_34_2 and is of type INTEGER.

Parameter 35: 5th gestures sequence (SLOT 5)

Value containing sequence of gestures. User can create sequences of two or three gestures to expand number of possible actions. Every sequence is saved in its advanced parameter (no. 31-36) with 16 bits, every basic gesture is identified with 4 bits.

Gesture Value

Empty 0

^ 1

v 2

< 3

> 4

Rules of creating sequences:

• Maximum of six sequences can be created.

• Each sequence must be unique.

• Sequence can consist of two or three basic gestures (left, right, up

or down).

• Two identical gestures cannot be used next to each other

To manually create or edit a sequence slot:

1. Calculate new value of parameter using table and formula:

Value of parameter = 256 * Value of first gesture + 16 * Value of second gesture + Value of third gesture

2. Change the value of corresponding parameter (parameters 31 to 36 for slots 1 to 6).

N.B. Setting parameter to 0 will delete the sequence.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1076 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_35_2 and is of type INTEGER.

Parameter 36: 6th gestures sequence (SLOT 6)

Value containing sequence of gestures. User can create sequences of two or three gestures to expand number of possible actions. Every sequence is saved in its advanced parameter (no. 31-36) with 16 bits, every basic gesture is identified with 4 bits.

Gesture Value

Empty 0

^ 1

v 2

< 3

> 4

Rules of creating sequences:

• Maximum of six sequences can be created.

• Each sequence must be unique.

• Sequence can consist of two or three basic gestures (left, right, up

or down).

• Two identical gestures cannot be used next to each other

To manually create or edit a sequence slot:

1. Calculate new value of parameter using table and formula:

Value of parameter = 256 * Value of first gesture + 16 * Value of second gesture + Value of third gesture

2. Change the value of corresponding parameter (parameters 31 to 36 for slots 1 to 6).

N.B. Setting parameter to 0 will delete the sequence.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1076 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_36_2 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The FGGC001 supports 6 association groups.

Group 1: Lifeline

This group supports 1 nodes.

Group 2: Flick up gesture

This group supports 5 nodes.

Group 3: Flick down gesture

This group supports 5 nodes.

Group 4: Flick left gesture

This group supports 5 nodes.

Group 5: Flick right gesture

This group supports 5 nodes.

Group 6: Circular Airwheel

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_CRC_16_ENCAP_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V0  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_CENTRAL_SCENE_V2 Linked to BASIC
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V0  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V0  
COMMAND_CLASS_SECURITY_V0  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.