The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

FGMS001 Motion Sensor

This describes the Z-Wave device FGMS001, manufactured by Fibargroup with the thing type UID of fibaro_fgms001_03_002. This version of the device is limited to firmware versions above 3.2

The device is in the category of Motion Detector, defining Motion sensors/detectors.

FGMS001 product image

The FGMS001 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The FGMS001 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the FGMS001 -:

Channel Channel Id Category Item Type
Binary Sensor sensor_binary Door Switch
Sensor (temperature) sensor_temperature Temperature Number
Sensor (seismic intensity) sensor_seismicintensity Humidity Number
Sensor (luminance) sensor_luminance Temperature Number
Motion Alarm alarm_motion Door Switch
Tamper Alarm alarm_tamper   Switch
Battery Level battery-level Battery Number
Alarm (general) alarm_general Door Switch

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Sensor (temperature)

Indicates the current temperature.

The sensor_temperature channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Sensor (seismic intensity)

Indicates the current seismic intensity level.

The sensor_seismicintensity channel supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.

Sensor (luminance)

Indicates the current light reading.

The sensor_luminance channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Motion Alarm

Indicates if a motion alarm is triggered.

The alarm_motion channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Tamper Alarm

Indicates if the tamper alarm is triggered.

The alarm_tamper channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Alarm (general)

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Device Configuration

The following table provides a summary of the 30 configuration parameters available in the FGMS001. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Motion detection - sensitivity The lower the value, the more sensitive the PIR sensor.
2 Motion detection - blind time Period of time through which the PIR sensor is “blind”.
3 Motion detection - pulse counter Sets the number of moves required for the PIR sensor to report motion.
4 Motion detection - window time The higher the value, the more sensitive the PIR sensor.
6 Motion detection - alarm cancellation delay Period of time after wich Motion alarm will be cancelled.
8 Motion detection - operating mode The parameter determines the part of day in which the PIR sensor will be active.
9 Motion detection - night/day The parameter defines the difference between night and day.
12 BASIC command class configuration Determines the command frames sent in 1-st association group.
14 BASIC ON command frame value The value of 255 allows to turn ON a device.
16 BASIC OFF command frame value The value of 0 allows to turn OFF a device.
18 Associations in Z-Wave network Security Mode This parameter defines how commands are sent in specified association groups
20 Tamper - sensitivity Change in force that will result in tamper alarm
22 Tamper - alarm cancellation delay Time period after which a tamper alarm will be cancelled.
24 Tamper - operating modes This parameter determines function of the tamper and sent reports
25 Tamper - alarm cancellation This parameter allows to disable cancellation of the tamper alarm.
28 Tamper - broadcast mode Determines whether the tamper alarm frame will be sent in broadcast mode
29 Tamper - backward compatible broadcast mode Determines whether the tamper alarm frame will be sent in broadcast mode
40 Illuminance report - threshold Change in light intensity level resulting in illumination report
42 Illuminance report - interval Time interval between consecutive illumination reports
60 Temperature report - threshold The change in temperature resulting in temperature report
62 Temperature measuring - interval How often the temperature will be measured
64 Temperature report - interval How often the temperature reports will be sent
66 Temperature offset Value added to the actual temperature
80 LED - signalling mode LED signalling mode
81 LED - brightness LED brightness
82 LED - illuminance for low indicator brightness Light intensity level below which brightness of visual indicator is set to 1%.
83 LED - illuminance for high indicator brightness Light intensity level above which brightness of visual indicator is set to 100%.
86 LED - temperature for blue colour Minimum temperature resulting in blue LED illumination
87 LED - temperature for red colour Minimum temperature resulting in red LED illumination
89 LED - tamper alarm Indicating mode resembles a police car (white, red and blue
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 1: Motion detection - sensitivity

The lower the value, the more sensitive the PIR sensor. The lower the value, the more sensitive the PIR sensor. Available settings: 8 - 255. Values in the range 8 to 255 may be set.

The manufacturer defined default value is 15.

This parameter has the configuration ID config_1_2 and is of type INTEGER.

Parameter 2: Motion detection - blind time

Period of time through which the PIR sensor is “blind”. Period of time through which the PIR sensor is “blind” (insensitive) to motion. After this time period the PIR sensor will be again able to detect motion. The longer the insensitivity period, the longer the battery life. If the sensor is required to detect motion quickly, the time period may be shortened. The time of insensitivity should be shorter that the time period set in parameter 6.
Available settings: 0 - 15
Formula to calculate the time: time [s] = 0.5 x (value + 1)
Default setting: 3 (1.5 seconds)
Parameter size: 1 [byte] Values in the range 0 to 15 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Motion detection - pulse counter

Sets the number of moves required for the PIR sensor to report motion. Sets the number of moves required for the PIR sensor to report motion. The lower the value, the less sensitive the PIR sensor. It’s not recommended to modify this parameter settings.
Available settings: 0 - 3
Formula to calculate the number of pulses: pulses = (value + 1) Default setting: 1 (2 pulses)
Parameter size: 1 [byte] The following option values may be configured -:

Value Description
0 1 pulse
1 2 pulses
2 3 pulses
3 4 pulses

The manufacturer defined default value is 1 (2 pulses).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Motion detection - window time

The higher the value, the more sensitive the PIR sensor. Period of time during which the number of moves set in parameter 3 must be detected in order for the PIR sensor to report motion. The higher the value, the more sensitive the PIR sensor. It’s not recommended to modify this parameter setting.
Available settings: 0 - 3
Formula to calculate the time: time [s] = 4 x (value + 1)
Default setting: 2 (12 seconds)
Parameter size: 1 [byte] The following option values may be configured -:

Value Description
0 4 seconds
1 8 seconds
2 12 seconds
3 16 seconds

The manufacturer defined default value is 2 (12 seconds).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 6: Motion detection - alarm cancellation delay

Period of time after wich Motion alarm will be cancelled. Motion alarm will be cancelled in the main controller and the associated devices after the period of time set in this parameter. Any motion detected during the cancellation delay time countdown will result in the countdown being restarted. In case of small values, below 10 seconds, the value of parameter 2 must be modified (PIR sensor’s “Blind Time”).
Available settings: 1 - 32767
Default setting: 30 (30 seconds)
Parameter size: 2 [bytes] Values in the range 1 to 32767 may be set.

The manufacturer defined default value is 30.

This parameter has the configuration ID config_6_2 and is of type INTEGER.

Parameter 8: Motion detection - operating mode

The parameter determines the part of day in which the PIR sensor will be active. The parameter determines the part of day in which the PIR sensor will be active. This parameter influences only the motion reports and associations. Tamper, light intensity and temperature measurements will be still active, regardless of this parameter settings. 0 - PIR sensor always active 1 - PIR sensor active during the day only 2 - PIR sensor active during the night only. Default setting: 0 Parameter size: 1 [byte] The following option values may be configured -:

Value Description
0 PIR sensor always active
1 PIR sensor active during the day only
2 PIR sensor active during the night only

The manufacturer defined default value is 0 (PIR sensor always active).

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: Motion detection - night/day

The parameter defines the difference between night and day. The parameter defines the difference between night and day, in terms of light intensity, used in parameter 8. Available settings: 1 - 32767 Default setting: 200 (200 lux) Parameter size: 2 [bytes] Values in the range 1 to 32767 may be set.

The manufacturer defined default value is 200.

This parameter has the configuration ID config_9_2 and is of type INTEGER.

Parameter 12: BASIC command class configuration

Determines the command frames sent in 1-st association group. The parameter determines the command frames sent in 1-st association group, assigned to PIR sensor.
0 - BASIC ON and BASIC OFF command frames sent in Basic Command Class.
1 - only the BASIC ON command frame sent in Basic Command Class.
2 - only the BASIC OFF command frame sent in Basic CommandClass.
Values of BASIC ON and BASIC OFF command frames may be modified by dedicated parameters.
Default setting: 0 Parameter size: 1 [byte] The following option values may be configured -:

Value Description
0 BASIC ON and BASIC OFF
1 Only the BASIC ON
2 Only the BASIC OFF

The manufacturer defined default value is 0 (BASIC ON and BASIC OFF).

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 14: BASIC ON command frame value

The value of 255 allows to turn ON a device. The value of 255 allows to turn ON a device. In case of the Dimmer, the value of 255 means turning ON at the last memorized state, e.g. the Dimmer turned ON at 30% and turned OFF using the value of 255, and then turned OFF, will be turned ON at 30%, i.e. the last memorized state.
Available settings: 0 - 255
Default setting: 255
Parameter size: 2 [byte] Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_14_2 and is of type INTEGER.

Parameter 16: BASIC OFF command frame value

The value of 0 allows to turn OFF a device. The command frame sent at the moment of motion alarm cancellation, after the cancellation delay time, specified in parameter 6, has passed. The value of 0 allows to turn a device OFF while the value of 255 allows to turn ON a device. In case of the Dimmer, the value of 255 means turning ON at the last memorized state, e.g. the Dimmer turned ON at 30% and turned OFF using the value of 255, and then turned OFF, will be turned ON at 30%, i.e. the last memorized state.
Available settings: 0 - 255
Default setting: 0
Parameter size: 2 [byte] Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_16_2 and is of type INTEGER.

Parameter 18: Associations in Z-Wave network Security Mode

This parameter defines how commands are sent in specified association groups This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is Active only in Z-Wave network security mode. It doesn’t apply to 1st Lifeline group.

Available settings: 0 - 15
0 - all groups sent as non-secure
1 - 2nd group sent as secure
2 - 3rd group sent as secure
4 - 4th group sent as secure
8 - 5th group sent as secure

Parameter values may be combined, e.g. 1+2=3 means that 2nd &
3rd group are sent as secure.

Default setting: 15 (all groups sent as secure)
Parameter size: 1 [byte] Values in the range 0 to 15 may be set.

The manufacturer defined default value is 15.

This parameter has the configuration ID config_18_1 and is of type INTEGER.

Parameter 20: Tamper - sensitivity

Change in force that will result in tamper alarm This parameter determines the change in force acting on the device, that will result in reporting tamper alarm - g-force acceleration.

Available settigs: 0 - 121 (0.08 - 2g; multiply by 0.016g; 0 = tamper inactive)
Default setting: 15 (0.320g)
Parameter size: 1 [byte] Values in the range 0 to 121 may be set.

The manufacturer defined default value is 20.

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Parameter 22: Tamper - alarm cancellation delay

Time period after which a tamper alarm will be cancelled. Time period after which a tamper alarm will be cancelled in the main controller and associated devices.

Available settings: 1 - 32767
Default setting: 30 (seconds)
Parameter size: 2 [bytes] Values in the range 1 to 32767 may be set.

The manufacturer defined default value is 30.

This parameter has the configuration ID config_22_2 and is of type INTEGER.

Parameter 24: Tamper - operating modes

This parameter determines function of the tamper and sent reports This parameter determines function of the tamper and sent reports. It is an advanced feature serving much more functions than just detection of tampering.

0 – Only tamper (default)
1 – Tamper and earthquake detector. Function may be used as a simple seismograph. Two reports including the strength of shock are
always sent. First, right after the detection and second (value=0) after tamper alarm cancellation delay time.
2 – Tamper and orientation in space. Three reports are sent right after tamper alarm cancellation delay time. The following option values may be configured -:

Value Description
0 Only tamper (default)
1 Tamper and earthquake detector
2 Tamper and orientation in space

The manufacturer defined default value is 0 (Only tamper (default)).

This parameter has the configuration ID config_24_1 and is of type INTEGER.

Parameter 25: Tamper - alarm cancellation

This parameter allows to disable cancellation of the tamper alarm. 0 - Do not send tamper cancellation report
1 - Send tamper cancellation report The following option values may be configured -:

Value Description
0 Do not send tamper cancellation report
1 Send tamper cancellation report

The manufacturer defined default value is 1 (Send tamper cancellation report).

This parameter has the configuration ID config_25_1 and is of type INTEGER.

Parameter 28: Tamper - broadcast mode

Determines whether the tamper alarm frame will be sent in broadcast mode The parameter determines whether the tamper alarm frame will or will not be sent in broadcast mode. Alarm frames sent in broadcast mode can be received by all of the devices within Communication range (if they accept such frames). When Fibaro Motion Sensor is operating in protected mode (secure mode), the value should remain default. Device operating in protected mode doesn’t send frames in broadcast mode.

0 - Tamper alarm reported to association groups.
1 - Tamper alarm reported in broadcast mode to 3rd association group.

Default setting: 0
Parameter size: 1 [byte] The following option values may be configured -:

Value Description
0 Reported to association groups.
1 Reported in broadcast mode to 3rd association group.

The manufacturer defined default value is 0 (Reported to association groups.).

This parameter has the configuration ID config_28_1 and is of type INTEGER.

Parameter 29: Tamper - backward compatible broadcast mode

Determines whether the tamper alarm frame will be sent in broadcast mode The parameter determines whether the tamper alarm frame will or will not be sent in broadcast mode. Alarm frames sent in broadcast mode can be received by all of the devices within Communication range (if they accept such frames). When Fibaro Motion Sensor is operating in protected mode (secure mode), the value should remain default. Device operating in protected mode doesn’t send frames in broadcast mode.

0 - Tamper alarm reported to association groups.
1 - Tamper alarm reported in broadcast mode to 5th association group.

Default setting: 0
Parameter size: 1 [byte] The following option values may be configured -:

Value Description
0 Reported to association groups.
1 Reported in broadcast mode to 5th association group.

The manufacturer defined default value is 0 (Reported to association groups.).

This parameter has the configuration ID config_29_1 and is of type INTEGER.

Parameter 40: Illuminance report - threshold

Change in light intensity level resulting in illumination report The parameter determines the change in light intensity level resulting in illumination report being sent to the main controller.

Available settings: 0 - 32767 (1-32767 lux; 0=reports are not sent) Values in the range 0 to 32767 may be set.

The manufacturer defined default value is 200.

This parameter has the configuration ID config_40_2 and is of type INTEGER.

Parameter 42: Illuminance report - interval

Time interval between consecutive illumination reports Time interval between consecutive illumination reports.
The reports are sent even if there are no changes in the light intensity.

Available settings: 0 - 32767 (1-32767 seconds; 0 = no reports)
Default setting: 3600 Values in the range 0 to 32767 may be set.

The manufacturer defined default value is 3600.

This parameter has the configuration ID config_42_2 and is of type INTEGER.

Parameter 60: Temperature report - threshold

The change in temperature resulting in temperature report The parameter determines the change in level of temperature resulting in temperature report being sent to the main controller.
Available settings: 0 - 255 (0.1 - 25.5oC; 0 = reports are not sent)
Default setting: 10 (1oC) Parameter size: 2 [byte] Values in the range 0 to 255 may be set.

The manufacturer defined default value is 20.

This parameter has the configuration ID config_60_2 and is of type INTEGER.

Parameter 62: Temperature measuring - interval

How often the temperature will be measured The parameter determines how often the temperature will be measured. The shorter the time, the more frequently the temperature will be measured, but the battery life will shorten.
Available settings: 0 - 32767 (1 - 32767 seconds; 0 = temperature will not be measured)
Default setting: 900 (900 seconds)
Parameter size: 2 [bytes] Values in the range 0 to 32767 may be set.

The manufacturer defined default value is 900.

This parameter has the configuration ID config_62_2 and is of type INTEGER.

Parameter 64: Temperature report - interval

How often the temperature reports will be sent The parameter determines how often the temperature reports will be sent to the main controller.
Available settings: 0 - 32767 (1 - 32767 seconds; 0 = no reports)
Default setting: 0 Parameter size: 2 [byte] Values in the range 0 to 32767 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_64_2 and is of type INTEGER.

Parameter 66: Temperature offset

Value added to the actual temperature The value to be added to the actual temperature, measured by the sensor (temperature compensation).
Available settings: -1000 – 1000 (-1000-1000°C, 1°C step)
Default setting: 0 Parameter size: 2 [bytes] Values in the range -1000 to 1000 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_66_2 and is of type INTEGER.

Parameter 80: LED - signalling mode

LED signalling mode The parameter determines the way in which LED diode behaves after motion has been detected.
Values from 1 to 9 = single long blink at the moment of reporting motion. No other motion will be indicated until alarm is cancelled.
Values from 10 to 18 = single long blink at the moment of reporting motion and one short blink each time the motion is detected again.
Values from 19 to 26 = single long blink at the moment of reporting motion and two short blinks each time the motion is detected again. The following option values may be configured -:

Value Description
0 LED inactive.
1 LED colour depends on the temperature
2 Flashlight mode - LED glows in white for 10 seconds.
3 White.
4 Red.
5 Green.
6 Blue.
7 Yellow.
8 Cyan.
9 Magenta.
10 LED colour depends on the temperature
11 Flashlight mode
12 White.
13 Red.
14 Green.
15 Blue.
16 Yellow.
17 Cyan.
18 Magenta.
19 LED colour depends on the temperature
20 White.
21 Red.
22 Green.
23 Blue.
24 Yellow.
25 Cyan.
26 Magenta.

The manufacturer defined default value is 10 (LED colour depends on the temperature).

This parameter has the configuration ID config_80_1 and is of type INTEGER.

Parameter 81: LED - brightness

LED brightness The parameter determines the brightness of LED when indicating motion.
Available settings: 0 - 100 (1 - 100%; 0 = brightness determined by the ambient lighting - see parameters 82 and 83)
Default setting: 50 Parameter size: 1 [byte] Values in the range 0 to 100 may be set.

The manufacturer defined default value is 50.

This parameter has the configuration ID config_81_1 and is of type INTEGER.

Parameter 82: LED - illuminance for low indicator brightness

Light intensity level below which brightness of visual indicator is set to 1%. AMBIENT ILLUMINATION LEVEL BELOW WHICH LED BRIGHTNESS IS SET TO 1%

The parameter is relevant only when the parameter 81 is set to 0.
Available settings: 0 to parameter 83 value
Default setting: 100 (100 lux)
Parameter size: 2 [bytes] Values in the range 0 to 32767 may be set.

The manufacturer defined default value is 100.

This parameter has the configuration ID config_82_2 and is of type INTEGER.

Parameter 83: LED - illuminance for high indicator brightness

Light intensity level above which brightness of visual indicator is set to 100%. ABOVE WHICH LED BRIGHTNESS IS SET TO 100%

The parameter is relevant only when the parameter 81 is set to 0.
Available settings: parameter 82 value to 65535
Default setting: 1 000 (1 000 lux)
Parameter size: 2 [bytes] Values in the range 0 to 32767 may be set.

The manufacturer defined default value is 1000.

This parameter has the configuration ID config_83_2 and is of type INTEGER.

Parameter 86: LED - temperature for blue colour

Minimum temperature resulting in blue LED illumination This parameter is relevant only when parameter 80 has been properly configured.
Available settings: 0 to parameter 87 value (degrees celsius)
Default setting: 18 (18oC)
Parameter size: 2 [byte] Values in the range 0 to 255 may be set.

The manufacturer defined default value is 18.

This parameter has the configuration ID config_86_2 and is of type INTEGER.

Parameter 87: LED - temperature for red colour

Minimum temperature resulting in red LED illumination This parameter is relevant only when parameter 80 has been properly configured.
Available settings: parameter 86 value to 255 (degrees celsius)
Default setting: 28 (28oC)
Parameter size: 2 [byte] Values in the range 0 to 255 may be set.

The manufacturer defined default value is 28.

This parameter has the configuration ID config_87_2 and is of type INTEGER.

Parameter 89: LED - tamper alarm

Indicating mode resembles a police car (white, red and blue

The following option values may be configured -:

Value Description
0 LED does not indicate tamper alarm.
1 LED indicates tamper alarm.

The manufacturer defined default value is 1 (LED indicates tamper alarm.).

This parameter has the configuration ID config_89_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The FGMS001 supports 5 association groups.

Group 1: Lifeline

Device status This group supports 1 nodes.

Group 2: Motion

This group supports 5 nodes.

Group 3: Tamper

This group supports 5 nodes.

Group 4: Motion BC

Motion BC (backward compatibility) This group supports 5 nodes.

Group 5: Tamper BC

Tamper BC (backward compability) This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_APPLICATION_STATUS_V1  
COMMAND_CLASS_SENSOR_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SENSOR_MULTILEVEL_V7  
COMMAND_CLASS_CRC_16_ENCAP_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V3  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V0  
COMMAND_CLASS_SECURITY_V0  
COMMAND_CLASS_SENSOR_ALARM_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.