The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

FGS221 Double Relay Switch 2x1.5kW

This describes the Z-Wave device FGS221, manufactured by Fibargroup with the thing type UID of fibaro_fgs221_02_001. This version of the device is limited to firmware version 2.1

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

FGS221 product image

The FGS221 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the FGS221 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Switch 1 switch_binary1 Switch Switch
Switch 2 switch_binary2 Switch Switch

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Switch 2

Switch the power on and off.

The switch_binary2 channel supports the Switch item and is in the Switch category.

Device Configuration

The following table provides a summary of the 19 configuration parameters available in the FGS221. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Activate / deactivate functions ALL ON / ALL OFF Activate / deactivate functions ALL ON / ALL OFF
3 Auto off relay after specified time Auto off relay after specified time
4 Auto off for relay 1 Time period for auto off, in miliseconds 0 - Auto off disabled
5 Auto off for relay 2 Time period for auto off, in miliseconds 0 - Auto off disabled
6 Sending commands to group 1 devices Sending commands to group 1 devices
7 Sending commands to group 2 devices Sending commands to group 2 devices
13 Assigns bistable key status to the device status Assigns bistable key status to the device status
14 Switch type connector Switch type connector, you may choose between momentary and toggle switches
15 Operation of the Dimmer and Roller Shutter Controller Operation of the Dimmer and Roller Shutter Controller
16 Saving the state of the device after a power failure Fibaro Switch returns to the last position saved before a power failure
30 Relay 1: Response to General Alarm  
31 Relay 1: Response to Water Flood Alarm  
32 Relay 1: Response to Smoke, CO, CO2 Alarm  
33 Relay 1: Response to Temperature Alarm  
39 ALARM FLASHING alarm time Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame
40 Relay 2: Response to General Alarm  
41 Relay 2: Response to Water Flood Alarm  
42 Relay 2: Response to Smoke, CO, CO2 Alarm  
43 Relay 2: Response to Temperature Alarm  
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 1: Activate / deactivate functions ALL ON / ALL OFF

Activate / deactivate functions ALL ON / ALL OFF

The following option values may be configured -:

Value Description
0 ALL ON is not active ALL OFF is not active
1 ALL ON is not active ALL OFF active
2 ALL ON active ALL OFF is not active
255 ALL ON active, ALL OFF active

The manufacturer defined default value is 255 (ALL ON active, ALL OFF active).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 3: Auto off relay after specified time

Auto off relay after specified time Auto off relay after specified time, with the possibility of manual override - immediate Off after button push. The following option values may be configured -:

Value Description
0 Manual override disabled
1 Manual override enabled.

The manufacturer defined default value is 0 (Manual override disabled).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Auto off for relay 1

Time period for auto off, in miliseconds 0 - Auto off disabled

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_4_2 and is of type INTEGER.

Parameter 5: Auto off for relay 2

Time period for auto off, in miliseconds 0 - Auto off disabled

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_5_2 and is of type INTEGER.

Parameter 6: Sending commands to group 1 devices

Sending commands to group 1 devices Sending commands to control devices assigned to 1-st association group (key no. 1)
NOTE: Parameter 15 value must be set to 1 to work properly. This activates the double-click functionality - dimmer/roller shutter control The following option values may be configured -:

Value Description
0 Commands are sent when device is turned on and off
1 Commands sent when device off with memorized state
2 Commands are sent when device is turned off

The manufacturer defined default value is 0 (Commands are sent when device is turned on and off).

This parameter has the configuration ID config_6_1 and is of type INTEGER.

Parameter 7: Sending commands to group 2 devices

Sending commands to group 2 devices Sending commands to control devices assigned to 2-nd association group (key no. 2).

Info: Parameter 15 must be set to 1 to make this parameter work properly. This activates the double-click functionality - dimmer/roller shutter control. The following option values may be configured -:

Value Description
0 Commands are sent when device is turned on and off
1 Commands sent when device off with memorized state
2 Commands are sent when device is turned off

The manufacturer defined default value is 0 (Commands are sent when device is turned on and off).

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 13: Assigns bistable key status to the device status

Assigns bistable key status to the device status Info: Remote control from Fibaro System Is Still Possible. This function is useful When you want display status of external devices, e.g. Motion Sensor, in Fibaro System. The following option values may be configured -:

Value Description
0 [On / Off] device changes status on key status change
1 Device status depends on key status

The manufacturer defined default value is 0 ([On / Off] device changes status on key status change).

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Parameter 14: Switch type connector

Switch type connector, you may choose between momentary and toggle switches

The following option values may be configured -:

Value Description
0 Momentary switch
1 Toggle switch

The manufacturer defined default value is 1 (Toggle switch).

This parameter has the configuration ID config_14_1 and is of type INTEGER.

Parameter 15: Operation of the Dimmer and Roller Shutter Controller

Operation of the Dimmer and Roller Shutter Controller Operation of the Dimmer and Roller Shutter Controller - enabling this option allows the user to dim lighting/shut roller by associating dimmer/Roller Shutter Controller and holding or double press of double switch (only mono-stable switch). The following option values may be configured -:

Value Description
0 Dimmer/Roller Shutter Controller control is not active
1 Dimmer/Roller Shutter Controller control is active

The manufacturer defined default value is 0 (Dimmer/Roller Shutter Controller control is not active).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 16: Saving the state of the device after a power failure

Fibaro Switch returns to the last position saved before a power failure Options for changing the parameter 0-1 The following option values may be configured -:

Value Description
0 Fibaro Switch does not save the state after a power failure
1 Fibaro Switch saves its state before power failure

The manufacturer defined default value is 1 (Fibaro Switch saves its state before power failure).

This parameter has the configuration ID config_16_1 and is of type INTEGER.

Parameter 30: Relay 1: Response to General Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 1
1 Alarm relay 1 on
2 Alarm Relay 1 off
3 Alarm relay 1 flashing

The manufacturer defined default value is 3 (Alarm relay 1 flashing).

This parameter has the configuration ID config_30_1 and is of type INTEGER.

Parameter 31: Relay 1: Response to Water Flood Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 1
1 Alarm relay 1 on
2 Alarm relay 1 off
3 Alarm relay 1 flashing

The manufacturer defined default value is 2 (Alarm relay 1 off).

This parameter has the configuration ID config_31_1 and is of type INTEGER.

Parameter 32: Relay 1: Response to Smoke, CO, CO2 Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 1
1 Alarm relay 1 on
2 Alarm relay 1 off
3 Alarm relay 1 flashing

The manufacturer defined default value is 3 (Alarm relay 1 flashing).

This parameter has the configuration ID config_32_1 and is of type INTEGER.

Parameter 33: Relay 1: Response to Temperature Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 1
1 Alarm relay 1 on
2 Alarm relay 1 off
3 Alarm relay 1 flashing

The manufacturer defined default value is 1 (Alarm relay 1 on).

This parameter has the configuration ID config_33_1 and is of type INTEGER.

Parameter 39: ALARM FLASHING alarm time

Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 600.

This parameter has the configuration ID config_39_2 and is of type INTEGER.

Parameter 40: Relay 2: Response to General Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 2
1 Alarm relay 2 on
2 Alarm relay 2 off
3 Alarm relay 2 flashing

The manufacturer defined default value is 3 (Alarm relay 2 flashing).

This parameter has the configuration ID config_40_1 and is of type INTEGER.

Parameter 41: Relay 2: Response to Water Flood Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 2
1 Alarm relay 2 on
2 Alarm relay 2 off
3 Alarm relay 2 flashing

The manufacturer defined default value is 2 (Alarm relay 2 off).

This parameter has the configuration ID config_41_1 and is of type INTEGER.

Parameter 42: Relay 2: Response to Smoke, CO, CO2 Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 2
1 Alarm relay 2 on
2 Alarm relay 2 off
3 Alarm relay 2 flashing

The manufacturer defined default value is 3 (Alarm relay 2 flashing).

This parameter has the configuration ID config_42_1 and is of type INTEGER.

Parameter 43: Relay 2: Response to Temperature Alarm

The following option values may be configured -:

Value Description
0 Alarm deactivation relay 2
1 Alarm relay 2 on
2 Alarm relay 2 off
3 Alarm relay 2 flashing

The manufacturer defined default value is 1 (Alarm relay 2 on).

This parameter has the configuration ID config_43_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The FGS221 supports 3 association groups.

Group 1: Switch 1

This group supports 16 nodes.

Group 2: Switch 2

This group supports 16 nodes.

Group 3: Controller Updates

This group supports 1 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_WAKE_UP_V0| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|

Endpoint 2

Command Class Comment
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.