The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

FGSD002 Smoke Detector

This describes the Z-Wave device FGSD002, manufactured by Fibargroup with the thing type UID of fibaro_fgsd002_00_000.

The device is in the category of Smoke Detector, defining Smoke detectors.

FGSD002 product image

The FGSD002 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The FGSD002 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the FGSD002 -:

Channel Channel Id Category Item Type
Temperature Sensor sensor_temperature Temperature Number
Smoke Alarm alarm_smoke Door Switch
Tamper Alarm alarm_tamper   Switch
Low Battery Alarm alarm_battery   Switch
Hardware Failure Alarm alarm_system   Switch
Heat Alarm alarm_heat   Switch
Battery Level battery-level Battery Number
Clock Time Offset time_offset Temperature Number

Temperature Sensor

Indicates the current temperature.

The sensor_temperature channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Smoke Alarm

removed event specfic

event 3 is test button smoke alarm

event 2 is real smoke

Indicates if a smoke is triggered.

The alarm_smoke channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Tamper Alarm

Indicates if the tamper alarm is triggered.

The alarm_tamper channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Low Battery Alarm

Indicates if the low battery alarm is triggered.

The alarm_battery channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Hardware Failure Alarm

Indicates if a system alarm is triggered.

The alarm_system channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Heat Alarm

Indicates if a heat alarm is triggered.

The alarm_heat channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Clock Time Offset

Provides the current time difference for the devices time.

The time_offset channel supports the Number item and is in the Temperature category.

Device Configuration

The following table provides a summary of the 14 configuration parameters available in the FGSD002. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Smoke Sensor sensitivity There are 3 levels of sensitivity to smoke presence.
2 Z-Wave notifications status This parameter allows to activate excess temperature …
2 Z-Wave notifications status This parameter allows to activate excess temperature …
3 Visual indicator notifications status This parameter allows to activate visual indications
4 Sound notifications status This parameter allows to activate sound signals…
10 Configuration of control frames in BASIC command class This parameter defines which frames will be sent …
11 BASIC ON frame value BASIC ON frame is sent in case of smoke presence detection …
12 BASIC OFF frame value BASIC OFF frame is sent in case of FIRE ALARM cancellation.
13 Alarm broadcast A value other than 0 means that alarms are being sent in …
20 Temperature report interval Time interval between consecutive temperature reports.
21 Temperature report hysteresis The temperature report will only be sent if there is a difference …
30 Temperature threshold Temperature threshold for activating alarms
31 Excess temperature signaling interval Time interval of signaling (visual indication/sound) excess …
32 Lack of Z-Wave range indication interval Time interval of signaling (visual indication/sound) lack of …
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 1: Smoke Sensor sensitivity

There are 3 levels of sensitivity to smoke presence. Level 1 means the highest sensitivity. Rising the parameter value lowers the sensitivity to smoke presence. The following option values may be configured -:

Value Description
1 HIGH Sensitivity
2 MEDIUM Sensitivity
3 LOW Sensitivity

The manufacturer defined default value is 2 (MEDIUM Sensitivity).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Z-Wave notifications status

This parameter allows to activate excess temperature … … and/or enclosure opening notifications sent to the main controller The following option values may be configured -:

Value Description
0 All notifications disabled
1 Enclosure opening notification enabled
2 Exceeding temperature threshold notification enabled
3 All notifications enabled

The manufacturer defined default value is 255.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 2: Z-Wave notifications status

This parameter allows to activate excess temperature … … and/or enclosure opening notifications sent to the main controller Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Visual indicator notifications status

This parameter allows to activate visual indications but does not apply to major alarms, such as FIRE, TROUBLE and LOW BATTERY ALARM.

Available settings: 0 - 7 The following option values may be configured -:

Value Description
0 All notifications disabled
1 Enclosure opening notification enabled
2 Exceeding temperature threshold notification enabled
3 Enclosure opening notification enabled +
4 Lack of Z-Wave range notification
5 Enclosure opening notification enabled +
6 Exceeding temperature threshold notification enabled +
7 Enclosure opening notification enabled +

The manufacturer defined default value is 0 (All notifications disabled).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Sound notifications status

This parameter allows to activate sound signals… but does not apply to major alarms, such as FIRE, TROUBLE and LOW BATTERY ALARM. The following option values may be configured -:

Value Description
0 All notifications disabled
1 Enclosure opening notification enabled
2 Exceeding temperature threshold notification enabled
3 Enclosure opening notification enabled +
4 Lack of Z-Wave range notification
5 Enclosure opening notification enabled +
6 Exceeding temperature threshold notification enabled +
7 Enclosure opening notification enabled +

The manufacturer defined default value is 0 (All notifications disabled).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 10: Configuration of control frames in BASIC command class

This parameter defines which frames will be sent … in the 2-nd Association Group (FIRE ALARM). The values of BASIC ON and BASIC OFF frames may be defined as described in further parameters. The following option values may be configured -:

Value Description
0 BASIC ON and BASIC OFF enabled
1 BASIC ON enabled
2 BASIC OFF enabled

The manufacturer defined default value is 0 (BASIC ON and BASIC OFF enabled).

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 11: BASIC ON frame value

BASIC ON frame is sent in case of smoke presence detection … and FIRE ALARM triggering. Its value is defined by the parameter. Available settings: 0-99, 255. 0 - turn off the device. 1-99 - set the device to 1-99%. 255 - set the last status Values in the range 1 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_11_2 and is of type INTEGER.

Parameter 12: BASIC OFF frame value

BASIC OFF frame is sent in case of FIRE ALARM cancellation. Its value is defined by the parameter. Available settings: 0-99, 255. 0 - turn off the device. 1-99 - set the device to 1-99%. 255 - set the last status Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_12_2 and is of type INTEGER.

Parameter 13: Alarm broadcast

A value other than 0 means that alarms are being sent in … broadcast mode, i.e. to all devices within a Fibaro Smoke Sensor’s range The following option values may be configured -:

Value Description
0 broadcast inactive
1 FIRE ALARM broadcast (2-nd and 4-th Association Group) …
2 FIRE ALARM broadcast (2-nd and 4-th Association Group) …
3 FIRE ALARM broadcast (2-nd and 4-th Association Group) …

The manufacturer defined default value is 0 (broadcast inactive).

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Parameter 20: Temperature report interval

Time interval between consecutive temperature reports. Report is sent when new temperature value is different from the one previously reported - according to the set hysteresis (parameter 21). Temperature reports can be also sent as a result of polling.

Available settings: 0, 1-8640 (multiply by 10 seconds) [10s-24h]

0 – reports inactive
1-8640 - [10s-24h]

Default setting: 1 (10 seconds)
Parameter size: 2 [bytes] Values in the range 0 to 8640 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_20_2 and is of type INTEGER.

Parameter 21: Temperature report hysteresis

The temperature report will only be sent if there is a difference … in temperature value from the previous value reported, defined in this parameter (hysteresis). Temperature reports can be also sent as a result of polling.

Available settings: 1 – 100 (in 0,1oC steps)
1-100 - (multiply by 0,1) [0,1oC - 10oC]

Default setting: 10 (1oC)
Parameter size: 1 [byte] Values in the range 1 to 100 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_21_1 and is of type INTEGER.

Parameter 30: Temperature threshold

Temperature threshold for activating alarms This is the temperature threshold, measured by the internal sensor above which the excess temperature notification is sent (visual indication/sound/Z-Wave report).

Note that the alarm will not be deactivated again until the temperature drops by at least 2 degrees below this threshold. Values in the range 1 to 100 may be set.

The manufacturer defined default value is 55.

This parameter has the configuration ID config_30_1 and is of type INTEGER.

Parameter 31: Excess temperature signaling interval

Time interval of signaling (visual indication/sound) excess … temperature level

Available settings: 1-8640 (multiply by 10 seconds) [10s-24h]
1-8640 - [10s-24h]

Default setting: 1 (10 seconds)
Parameter size: 2 [bytes] Values in the range 1 to 8640 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_31_2 and is of type INTEGER.

Parameter 32: Lack of Z-Wave range indication interval

Time interval of signaling (visual indication/sound) lack of … Z-Wave range.

Available settings: 1-8640 (multiply by 10 seconds) [10s-24h]
1-8640 - [10s-24h]

Default setting: 180 (30min)
Parameter size: 2 [bytes] Values in the range 1 to 8640 may be set.

The manufacturer defined default value is 180.

This parameter has the configuration ID config_32_2 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The FGSD002 supports 5 association groups.

Group 1: Device Status

This group supports 1 nodes.

Group 2: Battery capacity low

This group supports 5 nodes.

Group 3: Tamper Alarm

This group supports 5 nodes.

Group 4: Fire Alarm

This group supports 5 nodes.

Group 5: Tamper Alarm

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_APPLICATION_STATUS_V1  
COMMAND_CLASS_SENSOR_MULTILEVEL_V5  
COMMAND_CLASS_CRC_16_ENCAP_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V0  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V3  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V0  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_TIME_PARAMETERS_V0  
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V0  
COMMAND_CLASS_SENSOR_ALARM_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.