FGCD001 Carbon Monoxide Sensor

This describes the Z-Wave device FGCD001, manufactured by Fibargroup with the thing type UID of fibaro_fgcd001_00_000.

Carbon Monoxide Sensor

Channels

The following table summarises the channels available for the FGCD001 Carbon Monoxide Sensor.

Channel Channel Id Channel Type UID Category Item Type
Binary Sensor sensor_binary sensor_binary Door Switch
Carbon Monoxide Sensor sensor_co sensor_co   Number
Sensor (temperature) sensor_temperature sensor_temperature Temperature Number
Alarm (CO) alarm_co alarm_co Door Switch
Alarm (heat) alarm_heat alarm_heat   Switch
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
Alarm (system) alarm_system alarm_system   Switch
Alarm (power) alarm_power alarm_power Door Switch
  battery-level system.battery-level    
Alarm (heat) alarm_heat alarm_heat   Switch
Alarm (CO) alarm_co alarm_co Door Switch
Alarm (general) alarm_general alarm_general Door Switch

Sensor (temperature)

Scale

Select the scale for temperature readings

Property Value      
Configuration ID config_scale      
Data Type TEXT   Default Value 0
Options Celsius (0)      
  Fahrenheit (1)      

Device Configuration

The following table provides a summary of the configuration parameters available in the FGCD001 Carbon Monoxide Sensor. Detailed information on each parameter can be found below.

Parameter Description
2: Z-Wave notifications This parameter allows to set the actions which result in sending notifications to the Z-Wa…
3: LED diode indications This parameter allows to set the actions which result in LED diode indications. This param…
4: Acoustic signals  
7: Associations in Z-Wave network security mode  
10: Commands sent to 2nd association group (CO Alarm)  
11: Value of BASIC ON command sent to 2nd association group  
12: Value of BASIC OFF command sent to 2nd association group  
13: Commands sent to 4th association group (CO Level)  
14: CO level required for sending BASIC ON command to 4th association group  
15: Time required for sending BASIC ON command to 4th association group  
16: Value of BASIC ON command sent to 4th association group  
17: CO Level required for sending BASIC OFF command to 4th association group  
19: Value of BASIC OFF command sent to 4th association group  
20: Temperature reporting time interval  
21: Temperature reporting hysteresis  
22: Threshold of exceeding the temperature  
23: CO meter activation  
25: CO level reporting hysteresis  
26: Threshold of CO meter activation  
1: Lifeline “Lifeline” reports the device status and allows for assigning single device only (main con…
2: CO Alarm Devices in this group will be switched on/off when CO Alarm status changes.
3: CO Alarm Devices in this group will receive notification when CO Alarm status changes.
4: CO Level Devices in this group will be switched on/off after exceeding the level of CO concentratio…
5: Tamper Alarm Sends tamper alarm and cancellation frames to the associated devices.
6: CO Alarm BC Devices in this group will receive sensor alarm frames when CO Alarm status changes.
7: Tamper Alarm BC Sends tamper alarm and alarm cancellation frames to the associated devices.

2: Z-Wave notifications

This parameter allows to set the actions which result in sending notifications to the Z-Wave network controller.

Overview

This parameter allows to set the actions which result in sending notifications to the Z-Wave network controller.

Default setting: 0

Parameter size: 1 [byte]

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 0
Options Both actions disabled (0)      
  Tampering (opened casing) (1)      
  Exceeding the temperature (2)      
  Both actions enabled (3)      

3: LED diode indications

This parameter allows to set the actions which result in LED diode indications. This parameter does not apply to the most important actions, such as CO Alarm, Malfunction Alarm and Low Battery Alarm.

Overview

This parameter allows to set the actions which result in LED diode indications.

This parameter does not apply to the most important actions, such as CO Alarm, Malfunction Alarm and Low Battery Alarm.

The CO Sensor allows to customize its operation to user’s needs.

Default setting: 0

Parameter size: 1 [byte]

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options All actions disabled (0)      
  Tampering (opened casing) (1)      
  Exceeding the temperature (2)      
  Tampering (opened casing) AND Exceeding the temperature (3)      
  Lack of Z-Wave range (4)      
  Tampering (opened casing) AND Lack of Z-Wave range (5)      
  Exceeding the temperature AND Lack of Z-Wave range (6)      
  Tampering AND Exceeding the temperature AND Lack of Z-Wave range (7)      

4: Acoustic signals

Overview

This parameter allows to set the actions which result in acoustic signals.

This parameter does not apply to the most important actions, such as CO Alarm, Malfunction Alarm and Low Battery Alarm.

Default setting: 0

Parameter size: 1 [byte]

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options All actions disabled (0)      
  Tampering (opened casing) (1)      
  Exceeding the temperature (2)      
  Tampering (opened casing) AND Exceeding the temperature (3)      
  Lack of Z-Wave range (4)      
  Tampering (opened casing) AND Lack of Z-Wave range (5)      
  Exceeding the temperature AND Lack of Z-Wave range (6)      
  Tampering AND Exceeding the temperature AND Lack of Z-Wave range (7)      

7: Associations in Z-Wave network security mode

Overview

Parameter defines how commands are sent in specified association groups: as secure or non-secure.

Parameter is active only in Z-Wave network security mode.

It does not apply to 1st “Lifeline” association group.

Available settings:

1 - 2nd group sent as secure

2 - 3rd group sent as secure

4 - 4th group sent as secure

8 - 5th group sent as secure

16 - 6th group sent as secure

32 - 7th group sent as secure

Parameter values may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure.

Default setting: 63

Parameter size: 1 [byte]

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 0 to 63
Default Value 63

10: Commands sent to 2nd association group (CO Alarm)

Overview

This parameter defines commands sent to devices associated in 2nd association group (CO Alarm).

Values of specified commands may be set in parameters 11 and 12.

Default setting: 3 (ON & OFF)

Parameter size: 1 [byte]

Property Value      
Configuration ID config_10_1      
Data Type INTEGER   Default Value 3
Options BASIC ON (1)      
  BASIC OFF (2)      
  BASIC ON & BASIC OFF (3)      

11: Value of BASIC ON command sent to 2nd association group

Overview

This parameter defines the value of BASIC ON command sent to devices in 2nd association group after the CO Alarm activation.

Default setting: 255 (turn on)

Parameter size: 2 [bytes]

Property Value      
Configuration ID config_11_2      
Data Type INTEGER   Default Value 255
Options Turning associated devices off (0)      
  Forcing level of associated devices (1)      
  Setting associated devices to the last remembered state or turning the (255)      

12: Value of BASIC OFF command sent to 2nd association group

Overview

This parameter defines the value of BASIC OFF command sent to devices in 2nd association group after the CO Alarm cancellation.

Available settings:

0-99 or 255

Setting parameter to appropriate value will result in:

0 - turning associated devices off

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them on

Default setting: 0 (turn off)

Parameter size: 2 [bytes]

Property Value
Configuration ID config_12_2
Data Type INTEGER
Range 0 to 255
Default Value 0

13: Commands sent to 4th association group (CO Level)

Overview

This parameter defines commands sent to devices associated in 4th association group (CO Level).

Values of specified commands may be set in parameters 16 and 19.

Available settings:

1 - BASIC ON

2 - BASIC OFF

3 - BASIC ON & BASIC OFF

Default setting: 3 (ON & OFF)

Parameter size: 1 [byte]

Property Value
Configuration ID config_13_1
Data Type INTEGER
Range 1 to 3
Default Value 3

14: CO level required for sending BASIC ON command to 4th association group

Overview

This parameter defines the minimum level of CO concentration which exceeding will result in starting the timer set in parameter 15.

Available settings: 25-400 - CO concentration level in ppm

Parameter value must be at least 4 ppm higher than parameter 17 value.

Default setting: 40 (40 ppm)

Parameter size: 2 [bytes]

Property Value
Configuration ID config_14_2
Data Type INTEGER
Range 25 to 400
Default Value 40

15: Time required for sending BASIC ON command to 4th association group

Overview

This parameter defines the time during which the level of CO concentration should remain above the value set in parameter 14 to send the BASIC ON command to 4th association group.

Available settings:

0 - immediate sending of BASIC ON command

1-2880 (30s - 24h, in 30s steps)

Default setting: 0

Parameter size: 2 [bytes]

Property Value
Configuration ID config_15_2
Data Type INTEGER
Range 0 to 2880
Default Value 0

16: Value of BASIC ON command sent to 4th association group

Overview

This parameter defines the value of BASIC ON command sent to devices in 4th association group after exceeding the CO level set in parameter 14 through the time set in parameter 15.

Available settings: 0-99 or 255

Setting parameter to appropriate value will result in:

0 - turning associated devices off

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them on.

Default setting: 255 (turn on)

Parameter size: 2 [bytes]

Property Value
Configuration ID config_16_2
Data Type INTEGER
Range 0 to 255
Default Value 255

17: CO Level required for sending BASIC OFF command to 4th association group

Overview

This parameter defines the level of CO concentration below which falling will result in sending the BASIC OFF command to 4th association group. Available settings: 10-400 - CO concentration level in ppm

Default setting: 25 (25 ppm)

Parameter value must be at least 4 ppm lower than parameter 14 value.

Parameter size: 2 [bytes]

Property Value
Configuration ID config_17_2
Data Type INTEGER
Range 10 to 400
Default Value 25

19: Value of BASIC OFF command sent to 4th association group

Overview

This parameter defines the value of BASIC OFF command sent to devices in 4th association group after falling below the CO level set in parameter 17.

Available settings:

0-99 or 255

Setting parameter to appropriate value will result in:

0 - turning associated devices off

1-99 - forcing level of associated devices

255 - setting associated devices to the last remembered state or turning them on.

Default setting: 0 (turn off)

Parameter size: 2 [bytes]

Property Value
Configuration ID config_19_2
Data Type INTEGER
Range 0 to 255
Default Value 0

20: Temperature reporting time interval

Overview

Time interval (in seconds) between consecutive reports of temperature (done by built-in temperature sensor).

Short time interval means more frequent communication, which results in shortened battery life.

Available settings:

0 - no periodical reports

10-1440 (5min - 12h, in 30s steps)

Default setting: 0

Parameter size: 2 [bytes]

Property Value
Configuration ID config_20_2
Data Type INTEGER
Range 0 to 1440
Default Value 0

21: Temperature reporting hysteresis

Overview

This parameter defines a minimum change in temperature resulting in a report being sent to the main Z-Wave controller.

Available settings: 1-20 (0.5°C - 10°C, each 0.5°C)

Default setting: 2 (1°C)

Parameter size: 1 [byte]

Property Value
Configuration ID config_21_1
Data Type INTEGER
Range 1 to 20
Default Value 2

22: Threshold of exceeding the temperature

Overview

This parameter defines the temperature level, which exceeding will result in sending actions set in parameters 2, 3 and 4.

Available settings: 1-85 (1°C - 85°C, each 1°C)

Default setting: 55 (55°C)

Parameter size: 1 [byte]

Property Value
Configuration ID config_22_1
Data Type INTEGER
Range 1 to 85
Default Value 55

23: CO meter activation

Overview

This parameter activates reporting the value of CO concentration level to the main Z-Wave controller.

Available settings:

0 - disabled

1 - enabled

Default setting: 1 (enabled)

Parameter size: 1 [byte]

Property Value
Configuration ID config_23_1
Data Type INTEGER
Range 0 to 1
Default Value 1

25: CO level reporting hysteresis

Overview

This parameter defines a minimum change in CO concentration level which results in sending a new value to the main Z-Wave controller. Available settings:2-6 (10 ppm - 30 ppm, each 5 ppm)

Default setting: 2 (10 ppm)

Parameter size: 1 [byte]

Parameter is closely related to parameter 26.

Property Value
Configuration ID config_25_1
Data Type INTEGER
Range 2 to 6
Default Value 2

26: Threshold of CO meter activation

Overview

This parameter defines the CO concentration level, which exceeding will result in sending a new value to the main Z-Wave controller, according to parameter 25 settings.

Adjusting the value allows to get the accurate data in case of danger and helps to save the battery in normal conditions.

Available settings: 10-255 (ppm)

Default setting: 30 (30 ppm)

Parameter size: 2 [bytes]

Parameter is closely related to parameter 25.

Property Value
Configuration ID config_26_2
Data Type INTEGER
Range 10 to 255
Default Value 30

1: Lifeline

“Lifeline” reports the device status and allows for assigning single device only (main controller by default).

Overview

The device provides the association of six groups: 1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).

“LifeLine” group is reserved solely for the controller and hence only 1 node can be assigned. It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Notification report: The device uses Notification Command Class to report different events to 1st association group (Lifeline).

Notification Type Triggering Event CO Alarm

  1. Carbon monoxide detected, unknown location 
  2. Carbon monoxide test
  3. Replacement required 

Heat Alarm Overheat detected, unknown location Home Security Tampering, product covering removed Power Management Replace battery soon  System System hardware failure

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: CO Alarm

Devices in this group will be switched on/off when CO Alarm status changes.

Overview

2nd association group – “CO Alarm” is assigned to the device status - devices in this group will be switched on/off when CO Alarm status changes.

The CO Sensor in 2nd to 7th group allows to control 5 regular or multichannel devices per an association group.

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: CO Alarm

Devices in this group will receive notification when CO Alarm status changes.

Overview

3rd association group – “CO Alarm” is assigned to the device status - devices in this group will receive notification when CO Alarm status changes. Useful for devices that can trigger alarms.

The CO Sensor in 2nd to 7th group allows to control 5 regular or multichannel devices per an association group. 

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: CO Level

Devices in this group will be switched on/off after exceeding the level of CO concentration specified in parameter 14.

Overview

4th association group – “CO Level” is assigned to measured CO level - devices in this group will be switched on/off after exceeding the level of CO concentration specified in parameter 14.

The CO Sensor in 2nd to 7th group allows to control 5 regular or multichannel devices per an association group. 

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_4
Data Type TEXT
Range to

5: Tamper Alarm

Sends tamper alarm and cancellation frames to the associated devices.

Overview

5th association group – “Tamper Alarm” is assigned to the tamper - sends tamper alarm and cancellation frames to the associated devices.

The CO Sensor in 2nd to 7th group allows to control 5 regular or multichannel devices per an association group. 

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed. 

Property Value
Configuration ID group_5
Data Type TEXT
Range to

6: CO Alarm BC

Devices in this group will receive sensor alarm frames when CO Alarm status changes.

Overview

6th association group – “CO Alarm BC” is assigned to the device status - devices in this group will receive sensor alarm frames when CO Alarm status changes. Provides backward compatibility with controllers not supporting Z-Wave+ protocol.

The CO Sensor in 2nd to 7th group allows to control 5 regular or multichannel devices per an association group. 

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_6
Data Type TEXT
Range to

7: Tamper Alarm BC

Sends tamper alarm and alarm cancellation frames to the associated devices.

Overview

7th association group – “Tamper Alarm BC” is assigned to the tamper - sends tamper alarm and alarm cancellation frames to the associated devices. Provides backward compatibility with controllers not supporting Z-Wave+ protocol.

The CO Sensor in 2nd to 7th group allows to control 5 regular or multichannel devices per an association group. 

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_7
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.