FGWP102 Metered Wall Plug Switch

This describes the Z-Wave device FGWP102, manufactured by Fibargroup with the thing type UID of fibaro_fgwp102_03_002.

Metered Wall Plug Switch

Overview

FIBARO Wall Plug is a universal, Z-Wave Plus compatible, remotely controlled outlet adapter. This device may be applied wherever you want to control electrical devices with up to 2500W load.

The Wall Plug is equipped with a power and energy metering function. It uses a LED ring to visualize the current load with colour changing illumination and operating mode. This is the smallest and most attractive device of this type available in the world.

The Wall Plug may be operated using the B-button located on its casing or via any Z-Wave compatible controller.

Inclusion Information

To add the device to the Z-Wave network:

  1. Plug the device into a socket nearby the main Z-Wave controller.
  2. The LED ring will glow red signalling not being added (reset or remove the device otherwise).
  3. Set the main controller in (security/non-security) add mode (see the controller’s manual).
  4. Quickly, triple click the B-button located on the casing.
  5. Wait for the adding process to end.
  6. Successful adding will be confirmed by the Z-Wave controller’s message.

Exclusion Information

To remove the device from the Z-Wave network:

  1. Plug the device into a socket nearby the main Z-Wave controller.
  2. The LED ring will glow green signalling being added (removing is not necessary otherwise).
  3. Set the main controller into remove mode (see the controller’s manual).
  4. Quickly, triple click the B-button located on the casing.
  5. Wait for the removing process to end.
  6. Successful removing will be confirmed by the Z-Wave controller’s message.

Channels

The following table summarises the channels available for the FGWP102 Metered Wall Plug Switch.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Sensor (power) sensor_power sensor_power Energy Number
Electric meter (watts) meter_watts meter_watts Energy Number
Electric meter (kWh) meter_kwh meter_kwh Energy Number
Reset the total power consumption meter_reset meter_reset Energy Switch
Alarm (power) alarm_power alarm_power Door Switch

Device Configuration

The following table provides a summary of the configuration parameters available in the FGWP102 Metered Wall Plug Switch. Detailed information on each parameter can be found below.

Parameter Description
1: “Always On” mode Will turn on connected device permanently
2: Remember device status before the power failure determines how the Wall Plug will react in the event of power supply failure
3: Overload safety switch allows to turn off the controlled device in case of exceeding the defined power.
10: High priority power report minimum percentage change in active power
11: Standard power report minimum percentage change in active power
12: Power reporting interval defines the time interval of sending at most 5 standard power reports
13: Energy reporting threshold specifies the minimum change in energy consumption
14: Power and energy periodic reports defines time period between independent reports sent
15: Measuring energy consumed by the Wall Plug itself determines whether power metering should include the amount of power
20: Control of „On/Off (Button)” association group (2) Control of „On/Off (Button)” association group (2) devices
21: DOWN value - „On/Off (Power)” association group (3) Lower power threshold, used in parameter 23
22: UP value - „On/Off (Power)” association group (3) Upper power threshold, used in parameter 23.
23: The response after exceeding defined power values defines the way that 3rd association group devices are controlled.
24: SWITCH ON value - „On/Off” association groups SWITCH ON value - „On/Off” association groups
30: Active alarms Define Z-Wave network alarms to which the Wall Plug will respond
31: Response to alarm frames defines how the Wall Plug will respond to alarms
32: Alarm state duration specifies the duration of alarm state
40: Power load for violet colour determines maximum active power value
41: LED ring colour when controlled device is on LED ring colour when controlled device is on
42: LED ring colour when controlled device is off LED ring colour when controlled device is off
43: LED ring colour at the Z-Wave network alarm detection LED ring colour at the Z-Wave network alarm detection
50: Associations in Z-Wave network security mode defines how commands are sent in specified association groups
1: Lifeline  
2: On/Off (Button)  
3: On/Off (Power)  

1: “Always On” mode

Will turn on connected device permanently

Overview

In this mode Wall Plug will turn on connected device permanently and will stop reacting to attempts of turning it off (through Z-Wave network or pushing the B-button).

“Always On” function turns the Wall Plug into a power and energy meter. Connected device will not be turned off upon receiving an alarm frame from another Z-Wave device (parameter 31 will be ignored).

In “Always on” mode, connected device may be turned off after exceeding the power defined in parameter 3 or in case of detecting current greater than 110% of rated current. In such cases, connected device can be turned on again by pushing the B-button or sending a control frame. By default, overload protection is inactive.

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 0
Options function inactive (0)      
  function activated (1)      

2: Remember device status before the power failure

determines how the Wall Plug will react in the event of power supply failure

Overview

This parameter determines how the Wall Plug will react in the event of power supply failure (e.g. power outage or taking out from the electrical outlet).

After the power supply is back on, the Wall Plug can be restored to previous state or remain switched off.

This parameter is ignored in „Always On” mode - the device automatically turns ON after plugging it into the socket.

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 1
Options device remains switched off (0)      
  device restores the state from before the power failure (1)      

3: Overload safety switch

allows to turn off the controlled device in case of exceeding the defined power.

Overview

This function allows to turn off the controlled device in case of exceeding the defined power. Controlled device will be turned off even if “Always On” function is active (parameter 1).

Controlled device can be turned back on via B-button or sending a control frame. By default this function is inactive.

10-30000 (1.0-3000.0W, step 0.1W) - power threshold

Property Value      
Configuration ID config_3_2      
Data Type INTEGER      
Range 10 to 30000   Default Value 0
Options function inactive (0)      

10: High priority power report

minimum percentage change in active power

Overview

This parameter determines the minimum percentage change in active power that will result in sending power report to the main controller with the highest priority in the Z-Wave network.

By default, the Wall Plug immediately sends the power report if the power load changes by 80%.

1-99 - power change in percent

100 - reports are disabled

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 100
Default Value 80

11: Standard power report

minimum percentage change in active power

Overview

This parameter determines the minimum percentage change in active power that will result in sending power report to the main controller

Compared to parameter 10, the maximum number of reports sent is reduced (parameter 12) to 5 in a specified time interval. In addition, the reports are not sent in mode, which may result in overloading the Z-Wave network.

By default changes in power load may be reported up to 5 times per 30 seconds, when power load changes by 15%.

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 100
Default Value 15

12: Power reporting interval

defines the time interval of sending at most 5 standard power reports

Overview

This parameter defines the time interval of sending at most 5 standard power reports when the power changes by the value set in parameter 11. The higher the value of parameter 12, the fewer reports the device will send.

Settings in second

Default: 30s

Property Value
Configuration ID config_12_2
Data Type INTEGER
Range 5 to 600
Default Value 30

13: Energy reporting threshold

specifies the minimum change in energy consumption

Overview

This parameter specifies the minimum change in energy consumption (in relation to the previously reported), that will result in sending a new report.

0 - energy reports inactive
1-500 (0.01-5kWh, step 0.01kWh) - threshold

Default: 10 (0.1kWh)

Property Value      
Configuration ID config_13_2      
Data Type INTEGER      
Range 0 to 500   Default Value 10
Options energy reports inactive (0)      

14: Power and energy periodic reports

defines time period between independent reports sent

Overview

This parameter defines time period between independent reports sent when changes in power load have not been recorded or if changes are insignificant. By default reports are sent every hour.

Default: 3600 second (1h)

Property Value      
Configuration ID config_14_2      
Data Type INTEGER      
Range 5 to 32400   Default Value 3600
Options periodic reports inactive (0)      

15: Measuring energy consumed by the Wall Plug itself

determines whether power metering should include the amount of power

Overview

This parameter determines whether power metering should include the amount of power consumed by the Wall Plug itself. Results are being added to the value of power consumed by controlled device.

Property Value      
Configuration ID config_15_1      
Data Type INTEGER   Default Value 0
Options function inactive (0)      
  function activated (1)      

20: Control of „On/Off (Button)” association group (2)

Control of „On/Off (Button)” association group (2) devices

Overview

Controlling devices with the B-Button. This parameter is inactive in “Always On” mode (parameter 1).
Control as the Wall Plug:

  • switching the Wall Plug on – switch the devices on (parameter 24)
    switching the Wall Plug off – switch the devices off (parameter 24)

Control opposite to the Wall Plug:

  • switching the Wall Plug on – switch the devices off
  • switching the Wall Plug off – switch the devices on
Property Value      
Configuration ID config_20_1      
Data Type INTEGER   Default Value 0
Options control as the Wall Plug (0)      
  control opposite to the Wall Plug (1)      

21: DOWN value - „On/Off (Power)” association group (3)

Lower power threshold, used in parameter 23

Overview

Lower power threshold, used in parameter 23. DOWN value cannot be higher than a value specified in parameter 22.

Setting: 0-24900 (0.0-2490.0W, step 0.1W)

Default: 300 (30W)

Property Value
Configuration ID config_21_2
Data Type INTEGER
Range 0 to 24900
Default Value 300

22: UP value - „On/Off (Power)” association group (3)

Upper power threshold, used in parameter 23.

Overview

Upper power threshold, used in parameter 23. UP value cannot belower than a value specified in parameter 21.

Available settings: 100-25000 (10.0-2500.0W, step 0.1W)
Default setting: 500 (50W)

Property Value
Configuration ID config_22_2
Data Type INTEGER
Range 100 to 25000
Default Value 500

23: The response after exceeding defined power values

defines the way that 3rd association group devices are controlled.

Overview

This parameter defines the way that 3rd association group devices are controlled. Depends on the actual measured power (as parameters 21 and 22 settings).

Property Value      
Configuration ID config_23_1      
Data Type INTEGER   Default Value 6
Options turn the associated devices ON (DOWN) (1)      
  turn the associated devices OFF (DOWN) (2)      
  turn the associated devices ON (UP) (3)      
  turn the associated devices OFF (UP) (4)      
  combination of 1 and 4 (5)      
  combination of 2 and 3 (6)      

24: SWITCH ON value - „On/Off” association groups

SWITCH ON value - „On/Off” association groups

Overview

The value of BASIC SET command frame sent to the devices associated in „On/Off” association groups (2, 3).

„On/Off (Button)” association group - in accordance with parameter 20.
„On/Off (Power)” association group - in accordance with parameter 23.

Available settings: 0-99 or255

Default setting: 255

Property Value      
Configuration ID config_24_2      
Data Type INTEGER   Default Value 255
Options Default (255)      

30: Active alarms

Define Z-Wave network alarms to which the Wall Plug will respond

Overview

Available settings:

  • 1 - general alarm
  • 2 - smoke alarm
  • 4 - CO alarm
  • 8 - CO2 alarm
  • 16 - high temperature alarm
  • 32 - flood alarm
  • 63 - All
Property Value      
Configuration ID config_30_1      
Data Type INTEGER   Default Value 63
Options general alarm (1)      
  smoke alarm (2)      
  CO alarm (4)      
  CO2 alarm (8)      
  high temperature alarm (16)      
  flood alarm (32)      
  All (63)      

31: Response to alarm frames

defines how the Wall Plug will respond to alarms

Overview

This parameter defines how the Wall Plug will respond to alarms (device’s status change).

In case of values 1 or 2 the Wall Plug is operating normally and LED ring signals an alarm through time defined in parameter 32 or until the alarm is cancelled.

In case of values 5 to 50 the Wall Plug does not report status change, power changes, ignores BASIC SET command frames. After time defined in parameter 32 or after the alarm cancellation, connected device is set to the previous state.

Available settings: 0 - no reaction,

  • 1 - turn connected device on
  • 2 - turn connected device off
  • 5-50 (0.5-5.0s, step 0.1s) - cyclically change device state with set period
Property Value      
Configuration ID config_31_1      
Data Type INTEGER      
Range 5 to 50   Default Value 0
Options no reaction (0)      
  turn connected device on (1)      
  turn connected device off (2)      

32: Alarm state duration

specifies the duration of alarm state

Overview

This parameter specifies the duration of alarm state. If a device sending an alarm frame through the Z-Wave network sets alarm duration as well, this settings are ignored.

Available settings: 1-32400 (in seconds)
Default setting: 600 (10min)

Property Value
Configuration ID config_32_2
Data Type INTEGER
Range 1 to 32400
Default Value 600

40: Power load for violet colour

determines maximum active power value

Overview

This parameter determines maximum active power value, which when exceeded, causes the LED ring flash violet. Function is active only when parameter 41 is set to 1 or 2.

Available settings: 1000-30000 (100.0-3000.0W, step 0.1W)
Default setting: 25000 (2500W)

Property Value
Configuration ID config_40_2
Data Type INTEGER
Range 1000 to 30000
Default Value 25000

41: LED ring colour when controlled device is on

LED ring colour when controlled device is on

Overview

When set to 1 or 2, LED ring colour will change depending on active power and parameter 40. Other colours are set permanently and do not depend on power consumption.

Property Value      
Configuration ID config_41_1      
Data Type INTEGER   Default Value 1
Options illumination turned off completely (0)      
  colour changes continuously depending on active power (1)      
  colour changes in steps depending on active power (2)      
  white (3)      
  red (4)      
  green (5)      
  blue (6)      
  yellow (7)      
  cyan (8)      
  magenta (9)      

42: LED ring colour when controlled device is off

LED ring colour when controlled device is off

Overview

This parameter defines the illumination colour after turning off

Property Value      
Configuration ID config_42_1      
Data Type INTEGER   Default Value 0
Options illumination turned off completely (0)      
  LED ring is illuminated (1)      
  white (3)      
  red (4)      
  green (5)      
  blue (6)      
  yellow (7)      
  cyan (8)      
  magenta (9)      

43: LED ring colour at the Z-Wave network alarm detection

LED ring colour at the Z-Wave network alarm detection

Overview

This parameter defines the illumination colour in case of Z-Wave alarm.

Property Value      
Configuration ID config_43_1      
Data Type INTEGER   Default Value 2
Options illumination turned off completely (0)      
  no change in colour (1)      
  LED ring flashes red/blue/white (2)      
  white (3)      
  red (4)      
  green (5)      
  blue (6)      
  yellow (7)      
  cyan (8)      
  magenta (9)      

50: Associations in Z-Wave network security mode

defines how commands are sent in specified association groups

Overview

This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. This parameter does not apply to 1st „Lifeline” group

Property Value      
Configuration ID config_50_1      
Data Type INTEGER   Default Value 3
Options none of the groups sent as secure (0)      
  2nd group sent as secure (1)      
  3rd group sent as secure (2)      
  2nd and 3rd group sent as secure (3)      

1: Lifeline

Overview

1st Association Group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: On/Off (Button)

Overview

2nd Association Group – “On/Off (Button)” devices in this group will be switched on or off when relay status is changed using the B-button (uses Basic command class).

The Wall Plug in 2nd and 3rd group allows to control up to 10 regular or multichannel devices per an association group. “LifeLine” group is reserved solely for the controller and hence only 1 node can be assigned.

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: On/Off (Power)

Overview

3rd Association Group – “On/Off (Power)” devices in this group will be switched on or off depending on the current load (uses Basic command class).

The Wall Plug in 2nd and 3rd group allows to control up to 10 regular or multichannel devices per an association group. “LifeLine” group is reserved solely for the controller and hence only 1 node can be assigned.

It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.