The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

Shuttle S/L Drapery hardware

This describes the Z-Wave device Shuttle S/L, manufactured by Forest Group Nederland B.V with the thing type UID of forest_shuttlesl_00_000.

The device is in the category of Blinds, defining Roller shutters, window blinds, etc..

Shuttle S/L product image

The Shuttle S/L supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

Role type: always on slave

Node type: z-wave plus node

Inclusion Information

Set your main controller into learn mode. Press configuration button 3 times. Led 3 is ON. Press and hold once more for 4 seconds, led will start blinking for 10 seconds. The Shuttle Z-wave motor will be detected and included into the Z-wave network of your controller.

Exclusion Information

To exclude, set your main controller into exclude mode. Press configuration button 3 times. Led 3 is ON. Press and hold once more for 4 seconds, led will start blinking for 10 seconds. The Shuttle Z-wave motor will be detected and excluded into the Z-wave network of your controller.

You can also reset the device, but only use this if your main controller is not operable. For reset, press the config button 25 times and confirm by pressing the button once more for 4 seconds until the led blinks 3 times and goes off.

Wakeup Information

Not specified

Channels

The following table summarises the channels available for the Shuttle S/L -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Dimmer switch_dimmer DimmableLight Dimmer

Switch

Switch binary command can be used to turn the Shuttle LZ fully open or fully closed.

Value:

-0x00: Close

-0xFF: Open

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Dimmer

Values 0-99 (%) are used to set the rail to the preferred position.

Value 255 is used to set the curtain fully open.

The level change is stopped when:

- stop multilevel start level command is received

- the curtain reached an end position (fully open or full closed)

Because of version 3 of this command class, the shuttle LZ responds with the following types:

Primary switch type: 0x03

- 0xFF is Open

- 0x00 is Closed

Secondary switch type: 0x00 (NOT SUPPORTED)

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The device has no configuration parameters configured.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The Shuttle S/L supports 1 association group.

Group 1: Lifeline

This group supports 1 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_MULTILEVEL_V3  
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.