The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

32563 Smart Door Sensor

This describes the Z-Wave device 32563, manufactured by Jasco Products with the thing type UID of ge_smartdoorsensor_00_000.

32563 product image

The 32563 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The 32563 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

Inclusion Information

  1. Follow the instructions for your Z-Wave certified controller to include the device to the Z-Wave network.
  2. Once the controller is ready to include your Hinge Pin Smart Door Sensor press and release the manual/program button on the smart switch to include it in the network.

Exclusion Information

  1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.
  2. Once the controller is ready to exclude your device, press and release the manual/program button on the Hinge Pin Smart Door Sensor to exclude it from the network.

You may wish to reset all of your Hinge Pin Smart Door Sensor’s settings to their factory defaults. To do this, press the program button 10 times within 6 seconds. If your Door Sensor has been successfully reset, its LED light will blink for 3 seconds. This should only be used in the event your network’s primary controller is missing or otherwise inoperable.

Wakeup Information

  1. Press and hold the Z-wave Button for 6 seconds. It will be wake up and send “Wake Up Notification CC “ to HUB.
  2. It will sleep after timeout for 10 seconds, or sleep right away when received the “Wake Up No More Information CC”.

Channels

The following table summarises the channels available for the 32563 -:

Channel Channel Id Category Item Type
Binary Sensor sensor_binary Door Switch
Alarm (access) alarm_access Door Switch
Battery Level battery-level Battery Number

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Alarm (access)

Indicates if the access control alarm is triggered.

The alarm_access channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 1 configuration parameters available in the 32563. Detailed information on each parameter can be found in the sections below.

Param Name Description
20 Report Method Change Open/Close Report Method
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 20: Report Method

Change Open/Close Report Method

  1. Notification (Default)
  2. Basic Set
  3. Basic Report Values in the range 1 to 3 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The 32563 supports 3 association groups.

Group 1: 1

Z-Wave Plus Lifeline This group supports 5 nodes.

Group 2: 2

For Control This group supports 5 nodes.

Group 3: 3

For Control This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SENSOR_BINARY_V2 Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V2  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V4  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.