The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZW4002 In-Wall Smart Fan Control

This describes the Z-Wave device ZW4002, manufactured by Jasco Products with the thing type UID of ge_zw4002_00_000.

The device is in the category of HVAC, defining Air condition devices, Fans.

ZW4002 product image

The ZW4002 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

Basic Operation

Note: Before starting, fan must be set to ‘HIGH’ position using pull chain. The connected fan can then be turned ON/OFF and adjust speed levels in two ways:

  1. Manually from the front panel rocker of the In-wall Fan Control
  2. Remotely with a Z-Wave controller

Manual Control

To turn the connected fan ON: Press and release the top of the rocker. Note: Fan will return to last speed setting of Fan Control. Default setting – HIGH.

To turn the fan OFF: Press and release the bottom of the rocker.

Adjust fan speed

To decrease fan speed: Press and hold lower rocker.

To increase fan speed: Press and hold upper rocker.

The LED indicator confirms fan speed settings by flashing patterns

  • LOW – LED will blink every 2 seconds for 10 seconds
  • MEDIUM – LED will blink every second for 10 seconds
  • HIGH – LED will blink every half second for 10 seconds

Inclusion Information

Once the controller is ready to include your device, press and release the top or bottom of the smart fan control switch (rocker) to include it in the network.

Exclusion Information

Tap up or down

Wakeup Information

Tap up or down

Channels

The following table summarises the channels available for the ZW4002 -:

Channel Channel Id Category Item Type
Dimmer switch_dimmer DimmableLight Dimmer

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The following table provides a summary of the 2 configuration parameters available in the ZW4002. Detailed information on each parameter can be found in the sections below.

Param Name Description
3 Night Light Defines the behavior of the blue LED
4 Invert Switch Invert the ON/OFF Switch State
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 3: Night Light

Defines the behavior of the blue LED Default is Night Light mode where LED is on when switch is off. The following option values may be configured -:

Value Description
0 LED on when switch is OFF
1 LED on when switch is ON
2 LED always off

The manufacturer defined default value is 0 (LED on when switch is OFF).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Invert Switch

Invert the ON/OFF Switch State Setting this parameter to Yes will change the top of the switch to OFF and the bottom to ON. Note: If you invert the switches and also install the product upside down, the load will now be control. The following option values may be configured -:

Value Description
0 No
1 Yes

The manufacturer defined default value is 0 (No).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZW4002 supports 3 association groups.

Group 1: Lifeline

Z-Wave Plus Lifeline This group supports 5 nodes.

Group 2: Controlled with local load

Supports Basic Set and is controlled with the local load This group supports 5 nodes.

Group 3: Double Tap

Supports Basic Set and is controlled by double pressing the On or Off button This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_VERSION_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.