12729 In-Wall Smart Dimmer

This describes the Z-Wave device 12729, manufactured by Jasco Products with the thing type UID of ge_12729_00_000.

In-Wall Smart Dimmer

Inclusion Information

  1. Follow the instructions for your Z-wave certified controller to include a device to the Z-wave network.

  2. Once the controller is ready to include your device, press up and release the toggle switch to include it in the network.

Note: Your controller may need to be within 10 feet of the device to be included.

  1. Once your controller has confirmed that the device has been included, refresh the Z-wave network to optimize performance.

Channels

The following table summarises the channels available for the 12729 In-Wall Smart Dimmer.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the 12729 In-Wall Smart Dimmer. Detailed information on each parameter can be found below.

Parameter Description
4: Invert Switch Invert the ON/OFF Switch State.
7: On/Off Command Dim Step Indicates how many levels the dimmer will change for each dimming step.
8: On/Off Command Dim Rate This sets how often the dim level will change.
9: Local Control Dim Step Indicates how many levels the dimmer will change for each dimming step.
10: Local Control Dim Rate This sets how often the dim level will change.
11: ALL ON/ALL OFF Dim Step Indicates how many levels the dimmer will change for each dimming step.
12: ALL ON/ALL OFF Dim Rate This sets how often the dim level will change.

4: Invert Switch

Invert the ON/OFF Switch State.

Overview

If the switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off rocker settings can be reversed by changing parameter 4’s value to “1”.

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

7: On/Off Command Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 99
Default Value 1

8: On/Off Command Dim Rate

This sets how often the dim level will change.

Overview

The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels.

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 1 to 255
Default Value 3

9: Local Control Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 1 to 99
Default Value 1

10: Local Control Dim Rate

This sets how often the dim level will change.

Overview

The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels.

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 255
Default Value 3

11: ALL ON/ALL OFF Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 99
Default Value 1

12: ALL ON/ALL OFF Dim Rate

This sets how often the dim level will change.

Overview

The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two parameters allow dim rate adjustments from 10 milliseconds to 4.2 minutes to go from maximum-to-minimum or minimum-to-maximum brightness levels.

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 1 to 255
Default Value 3

Did you spot an error in the above definition or want to improve the content? You can edit the database here.