45606 2-Way Dimmer Switch

This describes the Z-Wave device 45606, manufactured by Jasco Products with the thing type UID of ge_45606_00_000.

2-Way Dimmer Switch

Channels

The following table summarises the channels available for the 45606 2-Way Dimmer Switch.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the 45606 2-Way Dimmer Switch. Detailed information on each parameter can be found below.

Parameter Description
3: Night Light Defines the behavior of the blue LED.
4: Invert Switch Change the top of the switch to OFF and the bottom of the switch to ON.
5: Ignore Start-Level (Receiving) This dimmer will start dimming from its current level.
7: On/Off Command Dim Step Indicates how many levels the dimmer will change for each dimming step.
8: On/Off Command Dim Rate Sets the rate at which the dimmer changes the light level.
9: Local Control Dim Step Indicates how many levels the dimmer will change for each dimming step.
10: Local Control Dim Rate Sets the dim rate
11: ALL ON/ALL OFF Dim Step Indicates how many levels the dimmer will change for each dimming step.
12: ALL ON/ALL OFF Dim Rate Sets the dim rate for the all on/off command

3: Night Light

Defines the behavior of the blue LED.

Overview

Default is Night Light mode where LED is on when switch is off.

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options LED on when switch is OFF (0)      
  LED on when switch is ON (1)      
  LED always off (2)      

4: Invert Switch

Change the top of the switch to OFF and the bottom of the switch to ON.

Overview

Note: If you invert the switches and also install the product upside down, remember the load will now be controlled by the right, not the left switch.

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

5: Ignore Start-Level (Receiving)

This dimmer will start dimming from its current level.

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

7: On/Off Command Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 99
Default Value 1

8: On/Off Command Dim Rate

Sets the rate at which the dimmer changes the light level.

Overview

This value indicates in 10 millisecond resolution, how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 1 to 255
Default Value 3

9: Local Control Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 1 to 99
Default Value 1

10: Local Control Dim Rate

Sets the dim rate

Overview

This value indicates in 10 millisecond resolution, how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the dimmer will change.

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 255
Default Value 3

11: ALL ON/ALL OFF Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 99
Default Value 1

12: ALL ON/ALL OFF Dim Rate

Sets the dim rate for the all on/off command

Overview

This value indicates in 10 millisecond resolution, how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the dimmer will change.

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 1 to 255
Default Value 3

Did you spot an error in the above definition or want to improve the content? You can edit the database here.