GE 12725 In-Wall Dimmer

This describes the Z-Wave device GE 12725, manufactured by Jasco Products with the thing type UID of ge_ge12725_00_000.

In-Wall Dimmer

Channels

The following table summarises the channels available for the GE 12725 In-Wall Dimmer.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the GE 12725 In-Wall Dimmer. Detailed information on each parameter can be found below.

Parameter Description
3: Night Light Defines the behavior of the blue LED.
4: Invert Switch Invert the ON/OFF Switch State.
5: Ignore Start-Level (Receiving) This dimmer will start dimming from its current level.
7: On/Off Command Dim Step Indicates how many levels the dimmer will change for each dimming step.
8: On/Off Command Dim Rate This value indicates in 10 millisecond resolution.
9: Local Control Dim Step Indicates how many levels the dimmer will change for each dimming step.
10: Local Control Dim Rate This value indicates in 10 millisecond resolution.
11: ALL ON/ALL OFF Dim Step Indicates how many levels the dimmer will change for each dimming step.
12: ALL ON/ALL OFF Dim Rate This value indicates in 10 millisecond resolution.

3: Night Light

Defines the behavior of the blue LED.
Default is Night Light mode where LED is on when switch is off.

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options LED on when switch is OFF (0)      
  LED on when switch is ON (1)      
  LED always off (2)      

4: Invert Switch

Invert the ON/OFF Switch State.
Setting this parameter to Yes will change the top of the switch to OFF and the bottom to ON.
Note: If you invert the switches and also install the product upside down, the load will now be control

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

5: Ignore Start-Level (Receiving)

This dimmer will start dimming from its current level.

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

7: On/Off Command Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 99
Default Value 1

8: On/Off Command Dim Rate

This value indicates in 10 millisecond resolution.
This sets how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 1 to 255
Default Value 3

9: Local Control Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 1 to 99
Default Value 1

10: Local Control Dim Rate

This value indicates in 10 millisecond resolution.
This sets how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 255
Default Value 3

11: ALL ON/ALL OFF Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 99
Default Value 1

12: ALL ON/ALL OFF Dim Rate

This value indicates in 10 millisecond resolution.
This sets how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 1 to 255
Default Value 3

Did you spot an error in the above definition or want to improve the content? You can edit the database here.