26931/ZW4006 In-Wall Smart Motion Switch

This describes the Z-Wave device 26931/ZW4006, manufactured by Jasco Products with the thing type UID of ge_zw4006_00_000.

In-Wall Smart Motion Switch

Overview

The switch enables wireless control of On/OFF functions of incandescent, LED, xenon, halogen and fluorescent lighting. Not only does it act as a switch but the GE In-Wall Smart Motion Switch has a built in PIR sensor which can control the local and be set in occupancy or vacancy mode.

Inclusion Information

  1. Follow the instructions for your Z-Wave certified controller to include the smart switch to the Z-Wave network.
  2. Once the controller is ready to include your smart switch, press and release the top or bottom button on the smart switch to include it in the network. 

Exclusion Information

  1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.
    1. Once the controller is ready to exclude your device, press and release the top or bottom button on the smart switch to exclude it from the network. 

Channels

The following table summarises the channels available for the 26931/ZW4006 In-Wall Smart Motion Switch.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Scene Number scene_number scene_number   Number
Binary Sensor sensor_binary sensor_binary Door Switch
Alarm (burglar) alarm_burglar alarm_burglar Door Switch
Switch 1 switch_binary1 switch_binary Switch Switch
Alarm (burglar) 2 alarm_burglar2 alarm_burglar Door Switch

Device Configuration

The following table provides a summary of the configuration parameters available in the 26931/ZW4006 In-Wall Smart Motion Switch. Detailed information on each parameter can be found below.

Parameter Description
1: Timeout Duration Amount of time the light stays on after motion stops
2: Dim level Change brightness of associated light bulb(s)
3: Operation Mode  
4: Association Mode Enable/Disable Association Mode
5: Invert Switch In a 3-way configuration, invert the connected Add-On Switch buttons
6: Motion Sensor Enable/Disable Motion Sensor
13: Motion Sensor Sensitivity Amount of motion required to turn on the light
14: Light Sensing Enable/Disable whether motion sensor only turns light on if room is dark
15: Reset Cycle  
19: Exclusion Mode  
1: Z-Wave Plus Lifeline Z-Wave Plus Lifeline
2: Basic Set Local Load Supports Basic Set and is controlled with the local load
3: Basic Set Buttons Supports Basic Set and is controlled by pressing the On or Off buttons

1: Timeout Duration

Amount of time the light stays on after motion stops

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 5
Options Test (5s) (0)      
  1 minute (1)      
  5 minutes (5)      
  15 minutes (15)      
  30 minutes (30)      
  Disable timeout (255)      

2: Dim level

Change brightness of associated light bulb(s)

Property Value      
Configuration ID config_2_1      
Data Type INTEGER      
Range 0 to 255   Default Value 255
Options Default (255)      

3: Operation Mode

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 3
Options Manual (1)      
  Vacancy (2)      
  Occupancy (3)      

4: Association Mode

Enable/Disable Association Mode

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

5: Invert Switch

In a 3-way configuration, invert the connected Add-On Switch buttons

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 0
Options Disabled (0)      
  Enabled (1)      

6: Motion Sensor

Enable/Disable Motion Sensor

Property Value      
Configuration ID config_6_1      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

13: Motion Sensor Sensitivity

Amount of motion required to turn on the light

Property Value      
Configuration ID config_13_1      
Data Type INTEGER   Default Value 2
Options High (1)      
  Medium (2)      
  Low (3)      

14: Light Sensing

Enable/Disable whether motion sensor only turns light on if room is dark

Property Value      
Configuration ID config_14_1      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

15: Reset Cycle

Property Value      
Configuration ID config_15_1      
Data Type INTEGER   Default Value 2
Options Disable (0)      
  10 secs (1)      
  20 secs (2)      
  30 secs (3)      
  45 secs (4)      
  27 mins (110)      

19: Exclusion Mode

Property Value      
Configuration ID config_19_1      
Data Type INTEGER   Default Value 0
Options Normal (0)      
  Alternate (1)      

1: Z-Wave Plus Lifeline

Z-Wave Plus Lifeline

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Basic Set Local Load

Supports Basic Set and is controlled with the local load

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Basic Set Buttons

Supports Basic Set and is controlled by pressing the On or Off buttons

Property Value
Configuration ID group_3
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.