The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

GWPN5 Multi-socket PowerNode (5-plug)

This describes the Z-Wave device GWPN5, manufactured by GreenWave Reality Inc. with the thing type UID of greenwave_gwpn5_00_000.

The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.

The GWPN5 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

This Configuration is for the 6 plug version of the PowerNode.

Inclusion Information

On the PowerNode, press and hold the sync button for approximately one second until the activity indicator displays a clockwise rotating pattern. This indicates the PowerNode is attempting inclusion. During this process, verify that the Gateway activity indicator still displays a clockwise rotating pattern.

After a few seconds, the rotating pattern on both the PowerNode and the Gateway stops. All bars turn green forming a circle for several seconds. This indicates a successful inclusion.

If all bars on the activity indicator start flashing instead of forming a solid circle, then the PowerNode inclusion process has failed, and you must start the sync process again. If syncing continually fails even though the PowerNode is close to the Gateway, then it may be an indication of a hardware fault, and the PowerNode might need replacing.

Exclusion Information

On the PowerNode, press and hold the Sync button for approximately one second until the PowerNode activity indicator begins to display a counter-clockwise rotating pattern. The PowerNode is attempting exclusion.

Channels

The following table summarises the channels available for the GWPN5 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Electric meter (watts) meter_watts Energy Number
Electric meter (kWh) meter_kwh Energy Number
Alarm alarm_general Door Switch
Switch 1 switch_binary1 Switch Switch
Electric meter (watts) 1 meter_watts1 Energy Number
Electric meter (kWh) 1 meter_kwh1 Energy Number
Switch 2 switch_binary2 Switch Switch
Electric meter (watts) 2 meter_watts2 Energy Number
Electric meter (kWh) 2 meter_kwh2 Energy Number
Switch 3 switch_binary3 Switch Switch
Electric meter (watts) 3 meter_watts3 Energy Number
Electric meter (kWh) 3 meter_kwh3 Energy Number
Switch 4 switch_binary4 Switch Switch
Electric meter (watts) 4 meter_watts4 Energy Number
Electric meter (kWh) 4 meter_kwh4 Energy Number
Switch 5 switch_binary5 Switch Switch
Electric meter (watts) 5 meter_watts5 Energy Number
Electric meter (kWh) 5 meter_kwh5 Energy Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Electric meter (watts)

Indicates the instantaneous power consumption.

The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh)

Indicates the energy consumption (kWh).

The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Alarm

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Electric meter (watts) 1

Indicates the instantaneous power consumption.

The meter_watts1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh) 1

Indicates the energy consumption (kWh).

The meter_kwh1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Switch 2

Switch the power on and off.

The switch_binary2 channel supports the Switch item and is in the Switch category.

Electric meter (watts) 2

Indicates the instantaneous power consumption.

The meter_watts2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh) 2

Indicates the energy consumption (kWh).

The meter_kwh2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Switch 3

Switch the power on and off.

The switch_binary3 channel supports the Switch item and is in the Switch category.

Electric meter (watts) 3

Indicates the instantaneous power consumption.

The meter_watts3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh) 3

Indicates the energy consumption (kWh).

The meter_kwh3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Switch 4

Switch the power on and off.

The switch_binary4 channel supports the Switch item and is in the Switch category.

Electric meter (watts) 4

Indicates the instantaneous power consumption.

The meter_watts4 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh) 4

Indicates the energy consumption (kWh).

The meter_kwh4 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Switch 5

Switch the power on and off.

The switch_binary5 channel supports the Switch item and is in the Switch category.

Electric meter (watts) 5

Indicates the instantaneous power consumption.

The meter_watts5 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh) 5

Indicates the energy consumption (kWh).

The meter_kwh5 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Device Configuration

The following table provides a summary of the 5 configuration parameters available in the GWPN5. Detailed information on each parameter can be found in the sections below.

Param Name Description
0 Min. variation of load current Minimum variation in load current before a message is sent.
1 No communication light Minutes after which the device will flash if controller communicate is lost
2 Wheel position Wheel position on the GreenWave device (read-only)
3 Power-on state Default state after power loss
4 LED for network error If the LED should indicate a network error by flashing or not
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 0: Min. variation of load current

Minimum variation in load current before a message is sent. Value in percent (30 => 30%) Values in the range 0 to 100 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_0_1 and is of type INTEGER.

Parameter 1: No communication light

Minutes after which the device will flash if controller communicate is lost

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 2.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Wheel position

Wheel position on the GreenWave device (read-only)

The following option values may be configured -:

Value Description
128 Black
129 Green
130 Dark Blue
131 Red
132 Yellow
133 Purple
134 Orange
135 Light Blue
136 Pink
137 Locked

The manufacturer defined default value is 0.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Power-on state

Default state after power loss

The following option values may be configured -:

Value Description
0 All OFF
1 Remember last state
2 All ON

The manufacturer defined default value is 2 (All ON).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: LED for network error

If the LED should indicate a network error by flashing or not

The following option values may be configured -:

Value Description
0 Disable the LED for network error
1 Enable the LED for network error

The manufacturer defined default value is 1 (Enable the LED for network error).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The GWPN5 supports 4 association groups.

Group 1: Wheel position change

This group supports 1 nodes.

Group 2: Current leakage on relay

This group supports 1 nodes.

Group 3: Power level change

The new power reading is sent if the delta of the change is greater than the defined minimum variation This group supports 1 nodes.

Group 4: Over-current detection

This group supports 1 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_SWITCH_ALL_V0| | | COMMAND_CLASS_METER_V2| | | COMMAND_CLASS_CRC_16_ENCAP_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_METER_V2| |

Endpoint 2

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_METER_V2| |

Endpoint 3

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_METER_V2| |

Endpoint 4

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_METER_V2| |

Endpoint 5

Command Class Comment
COMMAND_CLASS_BASIC_V0  
COMMAND_CLASS_SWITCH_BINARY_V1  
COMMAND_CLASS_METER_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.