The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

HKZW_SO03 Smart Plug

This describes the Z-Wave device HKZW_SO03, manufactured by Hank with the thing type UID of hank_hkzwso03_00_000.

The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.

HKZW_SO03 product image

The HKZW_SO03 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

WELL DONE!
You have picked the finest solution for your smart home, congratulations!
Now it’s time to enjoy these great features of your new Smart Plug:
- Wireless control of floor lamps and small appliances
- Energy monitoring in live mode or over time (your Z-Wave gateway needs to support this feature)
- Scene inclusion for custom automation scenarios when included to a Z-Wave gateway controller
- LED indicator displaying Z-Wave signal strength and power usage
- Security enabled Z-Wave device with AES signal encryption (requires a security enabled gateway controller for full functionality)
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Built-in range extender for a stronger, more reliable network
- 2 USB charging ports for your smart phone or tablet (no Z-Wave functionality)
- Built-in overload protection in Z-Wave outlet and USB ports

SPECIFICATIONS
Model Number: ZEN06
Z-Wave Signal Frequency: 908.42 MHz

Power: 110V, 60Hz
Maximum Load: 15A, 1800W
USB Charging Port Power: 1A and 2.4A Operating Temperature: 14 – 104 F Range: Up to 130 feet line of sight Installation and Use: Indoor only Dimensions: 4” x 2.5” x 1.2”
Weight: 7oz

Z-WAVE COMMAND CLASSES
This device requires the following command classes to be supported and recognized by your Z-Wave controller:
COMMAND_CLASS_ALLSWITCH
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GROUP_INFORMATION
COMMAND_CLASS_BASIC
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_DEVICE_RESET_LOCAL
COMMAND_CLASS_FIRMWARE_UPDATE_MD
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_METER
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SCENE_ACTIVATION COMMAND_CLASS_SCENE_ACTUATOR_CONFIGURATION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_VERSION
COMMAND_CLASS_ZWAVEPLUS_INFO

Inclusion Information

Z-WAVE INCLUSION

Auto Z-Wave Inclusion

  1. Put your Z-Wave controller in inclusion mode
  2. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
  3. LED indicator will flash blue
  4. A new on / off device should be recognized by your Z-Wave controller

Manual Z-Wave Inclusion

  1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
  2. Put your Z-Wave controller in inclusion mode
  3. Press and release the Z-Wave button 3 TIMES QUICKLY
  4. LED indicator will flash blue

5. A new on / off device should be recognized by your Z-Wave controller

Secure Z-Wave Inclusion

  1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller
  2. Put your Z-Wave controller in secure inclusion mode
  3. Press and HOLD the Z-Wave button for at least 3 seconds
  4. LED indicator will flash green
  5. LED indicator will turn solid green once the inclusion is completed. Please allow 5 minutes for configuration. DO NOT press any buttons or move the device during that time
  6. A new secure on / off device should be recognized by your Z-Wave controller

Exclusion Information

Z-WAVE EXCLUSION

1. Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave gateway controller

  1. Put your Z-Wave controller in exclusion mode
  2. Press and release the Z-Wave button 3 TIMES QUICKLY

4. LED indicator will flash orange

  1. The smart plug should disappear from your controller’s device list and LED indicator will remain solid orange for a few seconds to indicate exclusion

Please repeat the process following all steps carefully if the first attempt is unsuccessful

Channels

The following table summarises the channels available for the HKZW_SO03 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Scene Number scene_number   Number
Electric meter (kWh) meter_kwh Energy Number
Electric meter (volts) meter_voltage Energy Number
Electric meter (watts) meter_watts Energy Number
Electric meter (amps) meter_current Energy Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Scene Number

Triggers when a scene button is pressed.

The scene_number channel supports the Number item.

Electric meter (kWh)

Indicates the energy consumption (kWh).

The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (volts)

Indicates the instantaneous voltage.

The meter_voltage channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (watts)

Indicates the instantaneous power consumption.

The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (amps)

Indicates the instantaneous current consumption.

The meter_current channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Device Configuration

The following table provides a summary of the 4 configuration parameters available in the HKZW_SO03. Detailed information on each parameter can be found in the sections below.

Param Name Description
20 Overload Protection Overload Protection
21 On/Off Status Recovery After Power Failure On/Off Status Recovery After Power Failure
24 On/Off Status Change Notifications On/Off Status Change Notifications
27 Led Indicator Control Led Indicator Control
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 20: Overload Protection

Overload Protection 16.5A for over 5 seconds when this setting is enabled. We DO NOT recommend changing this parameter’s value as it may result in device damage and malfunction.

Values: 0 – Disabled; 1 – Enabled (default).

Size: 1 byte dec.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Parameter 21: On/Off Status Recovery After Power Failure

On/Off Status Recovery After Power Failure Parameter 21: Choose the recovery state for your Smart Plug if power outage occurs.

Values: 0 – Smart Plug remembers the status prior to power outage and turns back to it

(default); 1 – Smart Plug automatically turns ON once power is restored (it does not

remember the status prior to power outage); 2 – Smart Plug automatically turns OFF once

power is restored (it does not remember the status prior to power outage);

Size: 1 byte dec.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_21_1 and is of type INTEGER.

Parameter 24: On/Off Status Change Notifications

On/Off Status Change Notifications Parameter 24: Your Smart Plug will automatically send a notification to the controller and

other associated devices if its status changes from on to off or the other way round. Choose

when you want it to send the report.

Values: 0 – disabled (it will not send status change notifications); 1 – sends notification if

status is changed manually or remotely via Z-Wave (default); 2 – sends notification ONLY if

status is changed manually by pressing and releasing the Z-Wave button on the Smart Plug;

Size: 1 byte dec.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 2 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_24_1 and is of type INTEGER.

Parameter 27: Led Indicator Control

Led Indicator Control Parameter 27: You can choose how the LED indicator displays power consumption on thesmart plug

Values: 0 – LED indicator will display power consumption whenever the device is plugged in

(LED stays on at all times – default setting); 1 – LED indicator will display the level of power

consumption for 5 seconds only whenever the device is turned on or off (LED indicator will

stay off for most of the time)

Size: 1 byte dec.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_27_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_SCENE_ACTIVATION_V1  
COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1  
COMMAND_CLASS_METER_V3  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.