SCN04 Four-key Scene Controller

This describes the Z-Wave device SCN04, manufactured by Hank with the thing type UID of hank_scn04_00_000.

Four-key Scene Controller

Overview

Hank Z-Wave Scene Controller with 4 buttons. Supports security functions.

The Scene controller offers three button action types: short press, held down and release.

- If a button is pressed quickly (for less than a second), the scene controller sends a central scene notification command to association group 1. This message contains a scene number from 1-4 depending on which button is pressed. It also sends a basic set command to the items in the association group for the button (even groups numbered 2 to 8) and a multilevel set command to the nodes in the association group for the button with an uneven number (3 for button 1, 5 for button 2 etc.).
- If a button is pressed and held down for more than a second, the scene controller sends a central scene notification command to association group 1 as above. It also sends a multilevel start level change (i.e. dim up) command to the nodes in the association group for the button.
- If a button is released after it has been held down, the scene controller sends a similar central scene notification command as well as a multilevel stop command the buttons association group.

Inclusion Information

Included as non-secure device:

  1. Insert the LIR2450 battery.
  2. Set the Z-Wave network main controller into learning mode( see Z-Waave network controller operating manul).
  3. Triple click a button.
  4. If the inclusion is successful, the LED will blink in blue less than 5 seconds and then keep on for 15 seconds.

Included as a secure device:

  1. Insert the LIR2450 battery.
  2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual).
  3. Pressing and holding a button for 3 seconds.
  4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds.

Exclusion Information

  1. Insert the LIR2450 battery.
  2. Set the Z-Wave network main controller into remove mode (see Z-Wave controller operating manual).
  3. Triple click the a button, if the exclusion is successful, LED will blink in orange for less than 5 seconds and then keep on for 3 seconds.

Wakeup Information

Press and hold any button for three seconds.

Channels

The following table summarises the channels available for the SCN04 Four-key Scene Controller.

Channel Channel Id Channel Type UID Category Item Type
Scene Number scene_number scene_number   Number
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the SCN04 Four-key Scene Controller. Detailed information on each parameter can be found below.

Parameter Description
254: Enable configuration Lock/unlock all configuration parameters.
1: Central notification Scene commands and battery reports
2: Basic commands button 1 Send basic commands for button 1
3: Multilevel button 1 Send multilevel commands for button 1
4: Basic commands button 2 Send basic commands for button 2
5: Multilevel button 2 Send multilevel commands for button 2
6: Basic commands button 3 Send basic commands for button 3
7: Multilevel button 3 Send multilevel commands for button 3
8: Basic commands button 4 Send basic commands for button 4
9: Multilevel button 4 Send multilevel commands for button 4

254: Enable configuration

Lock/unlock all configuration parameters.

Overview

Lock/unlock configuration of unit.

0 = Unlock (default)
1 = Lock

Property Value      
Configuration ID config_254_1      
Data Type INTEGER   Default Value 0
Options Unlock (0)      
  Lock (1)      

1: Central notification

Scene commands and battery reports

Overview

Scene Controller will send the central scene notification command and battery report command to the associated nodes if any button is triggered.

Button 1-4 sends scene commands 1-4. I.e. button 1 sends scene 1, button 2 scene 2 etc. More info about all association group commands can be seen from the table below.

Button ID Group ID Action & Notification Any button 1 Press: Central scene notification ( Key Attributes=0 )
Hold: Central scene notification ( Key Attributes=2 )
Release: Central scene notification ( Key attributes=1 ) Button 1 2 Press: Basic Set
Hold: Reserve
Release: Reserve 3 Press: Switch multilevel set
Hold: Multilevel start level change
Release: Multilevel stop level change Button 2 4 Press: Basic Set
Hold: Reserve
Release: Reserve 5 Press: Switch multilevel set
Hold: Multilevel start level change
Release: Multilevel stop level change Button 3 6 Press: Basic Set
Hold: Reserve
Release: Reserve 7 Press: Switch multilevel set
Hold: Multilevel start level change
Release: Multilevel stop level change Button 4 8 Press: Basic Set
Hold: Reserve
Release: Reserve 9 Press: Switch multilevel set
Hold: Multilevel start level change
Release: Multilevel stop level change

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Basic commands button 1

Send basic commands for button 1

Overview

Scene Controller will send Basic Set command to the associated nodes if button 1 is pressed.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Multilevel button 1

Send multilevel commands for button 1

Overview

Scene Controller will send switch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 1 is pressed, hold and released, respectively.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Basic commands button 2

Send basic commands for button 2

Overview

Scene Controller will send Basic Set command to the associated nodes if button 2 is pressed.

Property Value
Configuration ID group_4
Data Type TEXT
Range to

5: Multilevel button 2

Send multilevel commands for button 2

Overview

Scene Controller will send switch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 2 is pressed, hold and released, respectively.

Property Value
Configuration ID group_5
Data Type TEXT
Range to

6: Basic commands button 3

Send basic commands for button 3

Overview

Scene Controller will send Basic Set command to the associated nodes if button 3 is pressed.

Property Value
Configuration ID group_6
Data Type TEXT
Range to

7: Multilevel button 3

Send multilevel commands for button 3

Overview

Scene Controller will send switch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 3 is pressed, hold and released, respectively.

Property Value
Configuration ID group_7
Data Type TEXT
Range to

8: Basic commands button 4

Send basic commands for button 4

Overview

Scene Controller will send Basic Set command to the associated nodes if button 4 is pressed.

Property Value
Configuration ID group_8
Data Type TEXT
Range to

9: Multilevel button 4

Send multilevel commands for button 4

Overview

Scene Controller will send switch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 4 is pressed, hold and released, respectively.

Property Value
Configuration ID group_9
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.