The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

HS-MS100+ HomeSeer Z-Wave Plus Motion Sensor

This describes the Z-Wave device HS-MS100+, manufactured by HomeSeer Technologies with the thing type UID of homeseer_hsms100_00_000.

The device is in the category of Motion Detector, defining Motion sensors/detectors.

HS-MS100+ product image

The HS-MS100+ supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The HS-MS100+ does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

Motion sensor can be included and operated in any Z-Wave network with other Z-Wave certified devices.
The features list:
1) Z-Wave Plus certified for wide compatibility (500 serials product)
2) Supports security 0 and security 2 protected mode with AES-128 encryption.
3) Motion sensor.
4) Tamper alarm by shock sensor.
5) The battery life is up to 1 year.
6) Low battery alarm.
7) Support firmware OTA.

Inclusion Information

1) Open the cover

2) Place the device withing the direct range of your Z-Wave controller

3) Set the main controller into inclusion mode

4a) “Secure Inclusion”. Hold Z-button for 5 sec and then release. The LED indicator should blink fast.

4b) “Non-secure Inclusion”. Press Z-button once. The LED indicator should blink fast.

5) Wait for the adding process to end

Exclusion Information

1) Open the cover

2) Place the device withing the direct range of your Z-Wave controller

3) Set the main controller into exclusion mode

4a) Triple click Z-button quickly. The LED indicator should blink fast.

5) Wait for the removing process to end

Wakeup Information

Press and hold Z button for more than 5 seconds and release

Channels

The following table summarises the channels available for the HS-MS100+ -:

Channel Channel Id Category Item Type
Binary Sensor sensor_binary Door Switch
Alarm (burglar) alarm_burglar Door Switch
Battery Level battery-level Battery Number

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Alarm (burglar)

Indicates if the burglar alarm is triggered.

The alarm_burglar channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 6 configuration parameters available in the HS-MS100+. Detailed information on each parameter can be found in the sections below.

Param Name Description
12 Motion sensor sensitivity Motion sensor sensitivity
14 Enable/Disable BASIC SET command Enable/Disable BASIC SET command
15 Value of the BASIC SET Value of the BASIC SET
17 Enable/ Disable shock alarm Enable/ Disable shock alarm
18 Motion timeout interval Motion timeout interval
32 Level of low battery Level of low battery
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 12: Motion sensor sensitivity

Motion sensor sensitivity The higher the value, the more sensitive the PIR sensor. Values in the range 1 to 8 may be set.

The manufacturer defined default value is 8.

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 14: Enable/Disable BASIC SET command

Enable/Disable BASIC SET command

The following option values may be configured -:

Value Description
0 Disable
1 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_14_1 and is of type INTEGER.

Parameter 15: Value of the BASIC SET

Value of the BASIC SET

The following option values may be configured -:

Value Description
0 Triggered value 255
1 Triggered value 0

The manufacturer defined default value is 0 (Triggered value 255).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 17: Enable/ Disable shock alarm

Enable/ Disable shock alarm

The following option values may be configured -:

Value Description
0 Do not send a vibration alarm
1 Send a vibration alarm

The manufacturer defined default value is 1 (Send a vibration alarm).

This parameter has the configuration ID config_17_1 and is of type INTEGER.

Parameter 18: Motion timeout interval

Motion timeout interval Set 0 to disable report.

Value 1 to 65535 set timeout of transmitting command when motion has not been sensed for a period of time Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 600.

This parameter has the configuration ID config_18_2 and is of type INTEGER.

Parameter 32: Level of low battery

Level of low battery The low level from 10% to 50% Values in the range 10 to 50 may be set.

The manufacturer defined default value is 20.

This parameter has the configuration ID config_32_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The HS-MS100+ supports 2 association groups.

Group 1: Group 1

This group supports 5 nodes.

Group 2: Group 2

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SENSOR_BINARY_V2  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V5  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  
COMMAND_CLASS_SECURITY_V0  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.