HS-DS100+ Homeseer Z-Wave Door/Window Sensor

This describes the Z-Wave device HS-DS100+, manufactured by HomeSeer Technologies with the thing type UID of homeseer_hsds100_00_000.

Homeseer Z-Wave Door/Window Sensor

Overview

HS-DS100+ is a battery operated sensor that is designed to issue Z-Wave commands when doors or windows are opened or closed. HSDS100+ may be associated directly with other Z-Wave devices or it may be used with a wide variety of Z-Wave hubs and controllers to trigger events, scenes and other automations.

Inclusion Information

  1. Ensure AAA batteries are installed. Pull plastic tab from battery compartment (if necessary)
  2. Put your home automation controller into ‘inclusion’ mode. Consult your system’s manual for details.
  3. HS-DS100+ may be included “securely” (option a) or “non-securely” (option b). If your automation controller does not support secure devices, or if you wish to improve battery life, add the sensor “non-securely”. Otherwise, include the sensor “securely”

    • a) Secure inclusion: Press and hold the Z-Wave button inside the sensor body for 3 seconds. Wait for the process to finish.
    • b) Non-Secure inclusion: Triple-click the Z-Wave button inside the sensor body. Wait for the process to finish.
  4. If successful, the sensor body LED will blink briefly and then stay on for 3 seconds. If unsuccessful, the LED with blink briefly and then turn off. Should this happen, repeat the inclusion process.

Note: If you want this Door/window sensor to function as a security device using secure/encrypted Z-Wave communications, then a security enabled Z-Wave controller is required. 

Exclusion Information

  1. Put your home automation controller into ‘exclusion’ mode. Consult your system’s manual for details.

  2. Triple-click the Z-Wave button inside the sensor body. If successful, the LED will turn off within 1 second. If unsuccessful, the LED with blink for 5 seconds. Should this happen, repeat the exclusion process.

Channels

The following table summarises the channels available for the HS-DS100+ Homeseer Z-Wave Door/Window Sensor.

Channel Channel Id Channel Type UID Category Item Type
Binary Sensor sensor_binary sensor_binary Door Switch
Tamper Alarm alarm_tamper alarm_tamper   Switch
Door Sensor sensor_door sensor_door Door Contact
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the HS-DS100+ Homeseer Z-Wave Door/Window Sensor. Detailed information on each parameter can be found below.

Parameter Description
14: Enable / Disable BASIC SET command Enable / Disable BASIC SET command
15: Value of BASIC SET  
32: Defines value of LOW BATTERY Defines value of LOW BATTERY
1: Group 1  
2: Group 2  

14: Enable / Disable BASIC SET command

Enable / Disable BASIC SET command

Overview

A setting of “0” disables the regular reporting feature and requires the sensor to be manually woken up to send updates. 

Property Value      
Configuration ID config_14_1      
Data Type INTEGER   Default Value 0
Options Disable (0)      
  Enable (1)      

15: Value of BASIC SET

Property Value      
Configuration ID config_15_1      
Data Type INTEGER   Default Value 0
Options Sends 255 value for open and 0 value for closed (0)      
  Sends 0 value for open and 255 value for closed (1)      

32: Defines value of LOW BATTERY

Defines value of LOW BATTERY

Property Value
Configuration ID config_32_1
Data Type INTEGER
Range 10 to 50
Default Value 20

1: Group 1

Overview

Group 1 reports the sensor’s condition, battery level and tamper state. 

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Group 2

Overview

Group 2 sends the BASIC SET command.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.