914TRL Touchpad Electronic Deadbolt

This describes the Z-Wave device 914TRL, manufactured by Black & Decker with the thing type UID of kwikset_914trl_00_000.

Touchpad Electronic Deadbolt

Overview

The following table provides a reference of the Alarm_Number related messages.

Alarm Type    Alarm Level            Notification Event  

021              001                      Lock Secured using Keyed cylinder or inside thumb-turn  

022              001                      Lock Un-Secured using Keyed cylinder or inside thumb-turn  

026              001                      Lock Auto Secured – Bolt Jammed (Not fully extended)

027              001                      Lock Auto Secured – Successful (Fully extended)  

017              001                      Lock Secured at Keypad – Bolt Jammed (Not fully extended)   

018              000 or User-ID#*   Lock Secured at Keypad – Successful (Fully extended)   

019              User-ID#*              Lock Un-Secured by User (User-ID) at Keypad  

023              001                      Lock Secured by Controller – Bolt Jammed (Not fully extended)   

024              001                      Lock Secured by Controller – Successful (Fully extended)   

025              001                      Lock Un-Secured by Controller – Successful (Fully retracted)  

112              User-ID#*              New User Code (User-ID#) added to the lock  

032              001                      All User Codes deleted from lock   

161              001                      Failed User Code attempt at Keypad  

162              User-ID#*             Attempted access by user (User-ID#) outside of scheduled   

167              001                      Low battery level   

168              001                      Critical battery level   

169              001                      Battery level too low to operate lock  

* User-ID# values: 001 to 030

Inclusion Information

 Press button “A” on the lock one time to include it in your system.

Exclusion Information

 Press button “A” on the lock one time to exclude it in your system.

Channels

The following table summarises the channels available for the 914TRL Touchpad Electronic Deadbolt.

Channel Channel Id Channel Type UID Category Item Type
Door Lock lock_door lock_door Door Switch
Alarm alarm_number alarm_number    
Alarm Raw alarm_raw alarm_raw   String
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the 914TRL Touchpad Electronic Deadbolt. Detailed information on each parameter can be found below.

Parameter Description
31: Auto Buzzer Beeping sound enabled.
31: Auto Lock Automatically re-locks door 30 seconds after unlocking.
31: Lock LED Status Door lock status LED blinks every 6 seconds.
40: Factory Default Reset to factory default settings.
1: Group 1  

31: Auto Buzzer

Beeping sound enabled.

Overview

Beeping sound enabled. When disabled, keypad buttons light red or amber when pressed.

ON position is factory default.

Note: It is recommended that the beeping sound is enabled during programming.

Property Value      
Configuration ID config_31_1_00100000      
Data Type INTEGER   Default Value 1
Options OFF (0)      
  ON (1)      

31: Auto Lock

Automatically re-locks door 30 seconds after unlocking.

Overview

Lock automatically re-locks door 30 seconds after unlocking. OFF position is factory default. If this switch is turned on, it will be disabled if all codes are deleted from the lock.

Property Value      
Configuration ID config_31_1_01000000      
Data Type INTEGER   Default Value 0
Options OFF (0)      
  ON (1)      

31: Lock LED Status

Door lock status LED blinks every 6 seconds.

Overview

Door lock status LED blinks every 6 seconds. ON position is factory default.

Property Value      
Configuration ID config_31_1_10000000      
Data Type INTEGER   Default Value 1
Options OFF (0)      
  ON (1)      

40: Factory Default

Reset to factory default settings.

Overview

Reset factory default settings, except for the anti-theft setting.

Property Value      
Configuration ID config_40_1_wo      
Data Type INTEGER      
Range 0 to 1   Default Value 0
Options Factory Default (1)      

1: Group 1

Property Value
Configuration ID group_1
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.