DZPA1 Plug-in Appliance Module

This describes the Z-Wave device DZPA1, manufactured by Leviton with the thing type UID of leviton_dzpa1_00_000.

Plug-in Appliance Module

Channels

The following table summarises the channels available for the DZPA1 Plug-in Appliance Module.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch

Device Configuration

The following table provides a summary of the configuration parameters available in the DZPA1 Plug-in Appliance Module. Detailed information on each parameter can be found below.

Parameter Description
4: Invert Switch Invert the ON/OFF Switch State.
5: Ignore Start-Level (Receiving) This dimmer will start dimming from its current level.
7: Night Light Defines the behavior of the blue LED. Default is Night Light mode where LED is on when swi…
7: On/Off Command Dim Step Indicates how many levels the dimmer will change for each dimming step.
8: On/Off Command Dim Rate This value indicates in 10 millisecond resolution.
9: Local Control Dim Step Indicates how many levels the dimmer will change for each dimming step.
10: Local Control Dim Rate This value indicates in 10 millisecond resolution.
11: ALL ON/ALL OFF Dim Step Indicates how many levels the dimmer will change for each dimming step.
12: ALL ON/ALL OFF Dim Rate This value indicates in 10 millisecond resolution.

4: Invert Switch

Invert the ON/OFF Switch State.
Setting this parameter to Yes will change the top of the switch to OFF and the bottom to ON.
Note: If you invert the switches and also install the product upside down, the load will now be control

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

5: Ignore Start-Level (Receiving)

This dimmer will start dimming from its current level.

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 0
Options No (0)      
  Yes (1)      

7: Night Light

Defines the behavior of the blue LED. Default is Night Light mode where LED is on when switch is off.

Property Value      
Configuration ID config_7_1      
Data Type INTEGER   Default Value 255
Options LED always off (0)      
  LED on when switch is ON (254)      
  LED on when switch is OFF (255)      

7: On/Off Command Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 99
Default Value 1

8: On/Off Command Dim Rate

This value indicates in 10 millisecond resolution.
This sets how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 1 to 255
Default Value 3

9: Local Control Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 1 to 99
Default Value 1

10: Local Control Dim Rate

This value indicates in 10 millisecond resolution.
This sets how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 255
Default Value 3

11: ALL ON/ALL OFF Dim Step

Indicates how many levels the dimmer will change for each dimming step.

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 99
Default Value 1

12: ALL ON/ALL OFF Dim Rate

This value indicates in 10 millisecond resolution.
This sets how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 1 to 255
Default Value 3

Did you spot an error in the above definition or want to improve the content? You can edit the database here.