The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

WT00Z-1 3-Way Wall Accessory Switch

This describes the Z-Wave device WT00Z-1, manufactured by Linear Corp with the thing type UID of linear_wt00z1_00_000.

The WT00Z-1 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the WT00Z-1 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Dimmer switch_dimmer DimmableLight Dimmer

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The following table provides a summary of the 18 configuration parameters available in the WT00Z-1. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Dim Start Level Set Ignore Start Level Bit When Transmitting Dim Commands
2 Suspend Group 4 Suspend Group 4
3 Night Light Relationship between LED and status of devices in Group 1
4 Invert Switch Setting the relationship between the top of the transmitter to ON or OFF
5 Ignore start level when recieving dim commands Ignore start level when recieving dim commands
7 ON/OFF dim rate dim step parameter valid values: 1-99
8 ON/OFF dim rate dim timer parameter valid values: 1-255
9 Local control dim rate dim step parameter valid values: 1-99
10 Local control dim rate dim timer parameter valid values: 1-255
11 ALL ON/ ALL OFF dim rate dim step parameter valid values: 1-99
12 ALL ON/ ALL OFF dim rate dim timer parameter valid values: 1-255
13 Disable group 4 during a dim command Disable group 4 during a dim command
14 Enable Shade Control Group 2 The switch can control shade control devices if this parameter is set to 1.
15 Enable Shade Control Group 3 The switch can control shade control devices if this parameter is set to 1.
16 Enable Shade Control Group 1 The switch can control shade control devices if this parameter is set to 1.
19 LED Transmission Indication LED Transmission Indication
20 Poll: minutes Frequency that WT00Z-1 will poll first node in Group 1
21 Poll first node in group 1 Activate/Deactivate polling of first node in Group 1
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Dim Start Level

Set Ignore Start Level Bit When Transmitting Dim Commands The WT00Z-1 can send Dim commands to Z-Wave enabled dimmers.The Dim command has a start level embedded in it. A dimmer receivingthis command will start dimming from that start level. However, thecommand can be sent so that the dimmer ignores the start level andinstead starts dimming from its current level. By default, the WT00Z-1sends the command so that the dimmer will start dimming from itscurrent dim level rather than the start level embedded in the command.To change this, simply set the configuration parameter to 0.

• Parameter No: 1•

Length: 1 Byte•

Valid Values = 0 or 1 (default 1)

NOTE:

Any ACT Z-Wave enabled dimmers have the configuration optionto ignore the start level no matter how you configure the WT00Z-1 The following option values may be configured -:

Value Description
0 Use Start Level
1 Ignore Start Level

The manufacturer defined default value is 1 (Ignore Start Level).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Suspend Group 4

Suspend Group 4 You may wish to disable transmitting commands to Z-Wave devices that are in Group 4 without “un-associating” those devices from the group. Setting parameter 2 to the value of 1 will stop the WT00Z-1 from transmitting to devices that are “associated” into Group 4.

• Parameter No: 2•

Length: 1

Byte• Valid Values = 0 or 1 (default 0 The following option values may be configured -:

Value Description
0 Enable Group 4
1 Disable Group 4

The manufacturer defined default value is 0 (Enable Group 4).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Night Light

Relationship between LED and status of devices in Group 1 The LED on the WT00Z-1 will by default, turn ON when the status of the devices in Group 1 is ON. To make the LED turn ON when the status of Group 1 is OFF set this parameter to a value of 1.

Parameter No: 3•

Length: 1 Byte•

Valid Values = 0 or 1 (default 0 The following option values may be configured -:

Value Description
0 On when load is on
1 On when load is off

The manufacturer defined default value is 0 (On when load is on).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Invert Switch

Setting the relationship between the top of the transmitter to ON or OFF To change the top of the transmitter to OFF and the bottom of the transmitter to ON, set parameter 4 to 1.

To change back to original settings, set this parameter to the value of 0.

Parameter No: 4

Length: 1 Byte

Valid Values = 0 or 1 (default 0) The following option values may be configured -:

Value Description
0 Top-ON, Bottom-OFF
1 Bottom-ON, Top-OFF

The manufacturer defined default value is 0 (Top-ON, Bottom-OFF ).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Ignore start level when recieving dim commands

Ignore start level when recieving dim commands The WT00Z-1 can send Dim commands to Z-Wave enabled dimmers. The Dim command has a start level embedded in it. A dimmer receiving this command will start dimming from that start level. However, the command can be sent so that the dimmer ignores the start level and instead start dimming from its current level. By default, the WT00Z-1 sends the command so that the dimmer will start dimming from its current dim level rather then the start level embedded in the command. To change this, simply set the configuration parameter to 0.

Parameter No: 5•

Length: 1 Byte

Valid Values = 0 or 1 (default 1 The following option values may be configured -:

Value Description
0 Use start level
1 Ignore start level

The manufacturer defined default value is 1 (Ignore start level).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 7: ON/OFF dim rate

dim step parameter valid values: 1-99

Values in the range 1 to 99 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 8: ON/OFF dim rate

dim timer parameter valid values: 1-255

Values in the range 1 to 255 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: Local control dim rate

dim step parameter valid values: 1-99

Values in the range 1 to 99 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_9_1 and is of type INTEGER.

Parameter 10: Local control dim rate

dim timer parameter valid values: 1-255

Values in the range 1 to 255 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 11: ALL ON/ ALL OFF dim rate

dim step parameter valid values: 1-99

Values in the range 1 to 99 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_11_1 and is of type INTEGER.

Parameter 12: ALL ON/ ALL OFF dim rate

dim timer parameter valid values: 1-255

Values in the range 1 to 255 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 13: Disable group 4 during a dim command

Disable group 4 during a dim command After the WT00Z-1 is commanded to stop dimming when dimming because of the DIM START command, it will then command the Z-Wave devices that are in Group 4 to its new level. To prevent the WT00Z-1 from commanding the Z-Wave devices in Group 4 during this particular occurrence, set Parameter 13 to the value of 1.

Parameter 13

Length: 1 Byte

Valid Values = 0 or 1 (default 0 The following option values may be configured -:

Value Description
0 Enable
1 Disable

The manufacturer defined default value is 0 (Enable).

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Parameter 14: Enable Shade Control Group 2

The switch can control shade control devices if this parameter is set to 1.

The following option values may be configured -:

Value Description
0 Disable
1 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_14_1 and is of type INTEGER.

Parameter 15: Enable Shade Control Group 3

The switch can control shade control devices if this parameter is set to 1.

The following option values may be configured -:

Value Description
0 Disable
1 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 16: Enable Shade Control Group 1

The switch can control shade control devices if this parameter is set to 1.

The following option values may be configured -:

Value Description
0 Disable
1 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_16_1 and is of type INTEGER.

Parameter 19: LED Transmission Indication

LED Transmission Indication The WT00Z-1 will flicker its LED when it is transmitting to any of its 4 groups. This flickering can be set to not flicker at all (set to 0), to flicker the entire time it is transmitting (set to 1), or to flicker for only 1 second when it begins transmitting (set to 2). By default, the WT00Z-1 is set to flicker for only 1 second.

Parameter 19

Length: 1 Byte

Valid Values = 0 , 1, 2 (default 2) The following option values may be configured -:

Value Description
0 Disable Flicker
1 Flicker while transmitting
2 Flicker for 1 second

The manufacturer defined default value is 2 (Flicker for 1 second).

This parameter has the configuration ID config_19_1 and is of type INTEGER.

Parameter 20: Poll: minutes

Frequency that WT00Z-1 will poll first node in Group 1 The WT00Z-1 will poll the first node in Group 1 in order to keep itself synchronized with the group if this configuration parameter is set to 1. How often it will poll is configured using this parameter.

Parameter 20

Length: 1 Byte

Valid Values = 1 through 255 (default: 2) Values in the range 1 to 255 may be set.

The manufacturer defined default value is 2.

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Parameter 21: Poll first node in group 1

Activate/Deactivate polling of first node in Group 1 The WT00Z-1 will poll the first node in Group 1 in order to keep itself synchronized with the group if this configuration parameter is set to 1.

Parameter 21

Length: 1 Byte

Valid Values = 0 , 1 (default 0) The following option values may be configured -:

Value Description
0 Do not poll first node in group
1 Poll first node in group

The manufacturer defined default value is 0 (Do not poll first node in group).

This parameter has the configuration ID config_21_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The WT00Z-1 supports 4 association groups.

Group 1: Associating Group 1

This group supports 5 nodes.

Group 2: Associating Group 2

This group supports 5 nodes.

Group 3: Associating Group 3

This group supports 5 nodes.

Group 4: Associating Group 4

This group supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_MULTILEVEL_V1  
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_INDICATOR_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.