WD500Z-1 Wall Dimmer Switch

This describes the Z-Wave device WD500Z-1, manufactured by Linear Corp with the thing type UID of linear_wd500z_00_000.

Wall Dimmer Switch

Channels

The following table summarises the channels available for the WD500Z-1 Wall Dimmer Switch.

Channel Channel Id Channel Type UID Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the WD500Z-1 Wall Dimmer Switch. Detailed information on each parameter can be found below.

Parameter Description
1: Dim Start Level A dimmer receiving this command will start dimming from that start level if this bit is se…
3: LED Indication The WD500Z-1 will flicker its LED when it is transmitting to any of its groups.
4: Invert Switch To change the top of the switch to OFF and the bottom to ON change parameter to 1.
14: Enable Shade Control Group 2 The switch can control shade control devices if this parameter is set to 1
15: Enable Shade Control Group 3 The switch can control shade control devices if this parameter is set to 1.
19: LED Transmission Indication The WD500Z-1 will flicker its LED when it is transmitting to any of its groups. Parameter …
1: UNKNOWN!!!  
2: Double Tap  
3: Triple Tap  

1: Dim Start Level

A dimmer receiving this command will start dimming from that start level if this bit is set to 0. If the bit is set to 1, the dimmer will ignore the start level and instead start dimming from its current level.

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 1
Options Use Start Level (0)      
  Ignore Start Level (1)      

3: LED Indication

The WD500Z-1 will flicker its LED when it is transmitting to any of its groups.

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options 0 (0)      
  1 (1)      

4: Invert Switch

To change the top of the switch to OFF and the bottom to ON change parameter to 1.

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options Top-ON, Bottom-OFF (0)      
  Bottom-ON, Top-OFF (1)      

14: Enable Shade Control Group 2

The switch can control shade control devices if this parameter is set to 1

Property Value      
Configuration ID config_14_1      
Data Type INTEGER   Default Value 0
Options Disable (0)      
  Enable (1)      

15: Enable Shade Control Group 3

The switch can control shade control devices if this parameter is set to 1.

Property Value      
Configuration ID config_15_1      
Data Type INTEGER   Default Value 0
Options Disable (0)      
  Enable (1)      

19: LED Transmission Indication

The WD500Z-1 will flicker its LED when it is transmitting to any of its groups. Parameter set to 0 = not flicker Parameter set to 1 = flicker the entire time of transmitting Parameter set to 2 = flicker for only 1 second.

Property Value      
Configuration ID config_19_1      
Data Type INTEGER   Default Value 2
Options Disable Flicker (0)      
  Flicker while transmitting (1)      
  Flicker for 1 second (2)      

1: UNKNOWN!!!

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Double Tap

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Triple Tap

Property Value
Configuration ID group_3
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.