WT00Z-1 3-Way Wall Accessory Switch

This describes the Z-Wave device WT00Z-1, manufactured by Linear Corp with the thing type UID of linear_wt00z1_00_000.

3-Way Wall Accessory Switch

Channels

The following table summarises the channels available for the WT00Z-1 3-Way Wall Accessory Switch.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the WT00Z-1 3-Way Wall Accessory Switch. Detailed information on each parameter can be found below.

Parameter Description
1: Dim Start Level Set Ignore Start Level Bit When Transmitting Dim Commands
2: Suspend Group 4 Suspend Group 4
3: Night Light Relationship between LED and status of devices in Group 1
4: Invert Switch Setting the relationship between the top of the transmitter to ON or OFF
5: Ignore start level when recieving dim commands Ignore start level when recieving dim commands
7: ON/OFF dim rate dim step parameter valid values: 1-99
8: ON/OFF dim rate dim timer parameter valid values: 1-255
9: Local control dim rate dim step parameter valid values: 1-99
10: Local control dim rate dim timer parameter valid values: 1-255
11: ALL ON/ ALL OFF dim rate dim step parameter valid values: 1-99
12: ALL ON/ ALL OFF dim rate dim timer parameter valid values: 1-255
13: Disable group 4 during a dim command Disable group 4 during a dim command
14: Enable Shade Control Group 2 The switch can control shade control devices if this parameter is set to 1.
15: Enable Shade Control Group 3 The switch can control shade control devices if this parameter is set to 1.
16: Enable Shade Control Group 1 The switch can control shade control devices if this parameter is set to 1.
19: LED Transmission Indication LED Transmission Indication
20: Poll: minutes Frequency that WT00Z-1 will poll first node in Group 1
21: Poll first node in group 1 Activate/Deactivate polling of first node in Group 1
1: Associating Group 1  
2: Associating Group 2  
3: Associating Group 3  
4: Associating Group 4  

1: Dim Start Level

Set Ignore Start Level Bit When Transmitting Dim Commands

Overview

The WT00Z-1 can send Dim commands to Z-Wave enabled dimmers.The Dim command has a start level embedded in it. A dimmer receivingthis command will start dimming from that start level. However, thecommand can be sent so that the dimmer ignores the start level andinstead starts dimming from its current level. By default, the WT00Z-1sends the command so that the dimmer will start dimming from itscurrent dim level rather than the start level embedded in the command.To change this, simply set the configuration parameter to 0.

• Parameter No: 1• 

Length: 1 Byte• 

Valid Values = 0 or 1 (default 1)

NOTE:

Any ACT Z-Wave enabled dimmers have the configuration optionto ignore the start level no matter how you configure the WT00Z-1

 

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 1
Options Use Start Level (0)      
  Ignore Start Level (1)      

2: Suspend Group 4

Suspend Group 4

Overview

You may wish to disable transmitting commands to Z-Wave devices that are in Group 4 without “un-associating” those devices from the group. Setting parameter 2 to the value of 1 will stop the WT00Z-1 from transmitting to devices that are “associated” into Group 4.

• Parameter No: 2•

 Length: 1 

Byte• Valid Values = 0 or 1 (default 0

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 0
Options Enable Group 4 (0)      
  Disable Group 4 (1)      

3: Night Light

Relationship between LED and status of devices in Group 1

Overview

The LED on the WT00Z-1 will by default, turn ON when the status of the devices in Group 1 is ON. To make the LED turn ON when the status of Group 1 is OFF set this parameter to a value of 1.

Parameter No: 3• 

Length: 1 Byte• 

Valid Values = 0 or 1 (default 0

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 0
Options On when load is on (0)      
  On when load is off (1)      

4: Invert Switch

Setting the relationship between the top of the transmitter to ON or OFF

Overview

To change the top of the transmitter to OFF and the bottom of the transmitter to ON, set parameter 4 to 1.

To change back to original settings, set this parameter to the value of 0.

Parameter No: 4

Length: 1 Byte

Valid Values = 0 or 1 (default 0)

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 0
Options Top-ON, Bottom-OFF (0)      
  Bottom-ON, Top-OFF (1)      

5: Ignore start level when recieving dim commands

Ignore start level when recieving dim commands

Overview

The WT00Z-1 can send Dim commands to Z-Wave enabled dimmers. The Dim command has a start level embedded in it. A dimmer receiving this command will start dimming from that start level. However, the command can be sent so that the dimmer ignores the start level and instead start dimming from its current level. By default, the WT00Z-1 sends the command so that the dimmer will start dimming from its current dim level rather then the start level embedded in the command. To change this, simply set the configuration parameter to 0.

Parameter No: 5•

Length: 1 Byte

Valid Values = 0 or 1 (default 1

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 1
Options Use start level (0)      
  Ignore start level (1)      

7: ON/OFF dim rate

dim step parameter valid values: 1-99

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 1 to 99
Default Value 3

8: ON/OFF dim rate

dim timer parameter valid values: 1-255

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 1 to 255
Default Value 10

9: Local control dim rate

dim step parameter valid values: 1-99

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 1 to 99
Default Value 3

10: Local control dim rate

dim timer parameter valid values: 1-255

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 1 to 255
Default Value 10

11: ALL ON/ ALL OFF dim rate

dim step parameter valid values: 1-99

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 1 to 99
Default Value 3

12: ALL ON/ ALL OFF dim rate

dim timer parameter valid values: 1-255

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 1 to 255
Default Value 10

13: Disable group 4 during a dim command

Disable group 4 during a dim command

Overview

After the WT00Z-1 is commanded to stop dimming when dimming because of the DIM START command, it will then command the Z-Wave devices that are in Group 4 to its new level. To prevent the WT00Z-1 from commanding the Z-Wave devices in Group 4 during this particular occurrence, set Parameter 13 to the value of 1.

Parameter 13

Length: 1 Byte

Valid Values = 0 or 1 (default 0

Property Value      
Configuration ID config_13_1      
Data Type INTEGER   Default Value 0
Options Enable (0)      
  Disable (1)      

14: Enable Shade Control Group 2

The switch can control shade control devices if this parameter is set to 1.

Property Value      
Configuration ID config_14_1      
Data Type INTEGER   Default Value 0
Options Disable (0)      
  Enable (1)      

15: Enable Shade Control Group 3

The switch can control shade control devices if this parameter is set to 1.

Property Value      
Configuration ID config_15_1      
Data Type INTEGER   Default Value 0
Options Disable (0)      
  Enable (1)      

16: Enable Shade Control Group 1

The switch can control shade control devices if this parameter is set to 1.

Property Value      
Configuration ID config_16_1      
Data Type INTEGER   Default Value 0
Options Disable (0)      
  Enable (1)      

19: LED Transmission Indication

LED Transmission Indication

Overview

The WT00Z-1 will flicker its LED when it is transmitting to any of its 4 groups. This flickering can be set to not flicker at all (set to 0), to flicker the entire time it is transmitting (set to 1), or to flicker for only 1 second when it begins transmitting (set to 2). By default, the WT00Z-1 is set to flicker for only 1 second.

Parameter 19

Length: 1 Byte

Valid Values = 0 , 1, 2 (default 2)

Property Value      
Configuration ID config_19_1      
Data Type INTEGER   Default Value 2
Options Disable Flicker (0)      
  Flicker while transmitting (1)      
  Flicker for 1 second (2)      

20: Poll: minutes

Frequency that WT00Z-1 will poll first node in Group 1

Overview

The WT00Z-1 will poll the first node in Group 1 in order to keep itself synchronized with the group if this configuration parameter is set to 1. How often it will poll is configured using this parameter.

Parameter 20

Length: 1 Byte

Valid Values = 1 through 255 (default: 2)

Property Value
Configuration ID config_20_1
Data Type INTEGER
Range 1 to 255
Default Value 2

21: Poll first node in group 1

Activate/Deactivate polling of first node in Group 1

Overview

The WT00Z-1 will poll the first node in Group 1 in order to keep itself synchronized with the group if this configuration parameter is set to 1.

Parameter 21

Length: 1 Byte

Valid Values = 0 , 1 (default 0)

Property Value      
Configuration ID config_21_1      
Data Type INTEGER   Default Value 0
Options Do not poll first node in group (0)      
  Poll first node in group (1)      

1: Associating Group 1

Overview

Nodes in this group are turned ON by tapping the top of the paddle or OFF by tapping the bottom of the paddle. Nodes associated into this group are dimmed by pressing and holding the bottom of the paddle until the desired dim level is reached or brightened by pressing and holding the top of the paddle until the desired level is reached. The LED on the WT00Z-1 will indicate the status of this group ONLY.

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Associating Group 2

Overview

Nodes in this group are turned ON by tapping the top of the paddle twice or OFF by tapping the bottom of the paddle twice. Nodes associated into this group are dimmed by tapping the bottom of the paddle once and then pressing and holding the bottom of the paddle until the desired dim level is reached or brightened by tapping the top  of  the  paddle  once  then  pressing and holding the top of the paddle  until the desire level is reached

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Associating Group 3

Overview

Nodes in this group are turned ON by tapping the top of the paddle three times or OFF by tapping the bottom of the paddle three times. Nodes associated into this group are dimmed by tapping the bottom of the paddle twice and then pressing and holding the bottom of the paddle until the desired dim level is reached or brightened by tapping the top of the paddle twice then pressing and holding the top of the paddle until the desired level is reached

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Associating Group 4

Overview

Nodes in this group are turned ON or OFF or set to a specific dim level when the WT00Z-1 is controlled remotely. You can place up to 5 nodes in each group. If controlling dimmers, for best results, associate the dimmers into the group first

Property Value
Configuration ID group_4
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.