ZHC5010 FUGA Wall 4-way Switch with LED + Relay

This describes the Z-Wave device ZHC5010, manufactured by Logic Home Control with the thing type UID of logic_zhc5010_00_000.

FUGA Wall 4-way Switch with LED + Relay

Overview

ZHC5010 is a wall switch module with Z-Wave communication. The module contains four buttons, four LEDs, a built-in relay switch and is designed to fit into a standard LK FUGA® wall box (one-module format). The ZHC5010 Wall Switch allows you to control the local load as well as Z-Wave connected devices in up to four additional Z-Wave groups.

Configuration updated: 2017-03-12 14:35:03, firmware 1.09

Inclusion Information

Place your primary controller in Adding Mode by following the manufacturer’s instructions, then activate the add mode on the device by triple-clicking the upper left button on the module, or by triple-clicking the little button in the middle of the module (hidden behind the small plastic cover). Adding Mode is indicated by blinking of upper left LED until the timeout occurs after 10 seconds or the module has been added in the network. 

Exclusion Information

Follow the inclusion procedures; the device is removed in the same manner, when the controller is in Removing Mode.

Factory reset:
ZHC5010 can be factory reset by pressing the small button in the middle of the module (normally covered by small plastic cover) for at least 10 seconds. Remove the middle plastic cover by means of a small screwdriver, and press the small button for at least 10 seconds, until all the LEDs lights up. Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Channels

The following table summarises the channels available for the ZHC5010 FUGA Wall 4-way Switch with LED + Relay.

Channel Channel Id Channel Type UID Category Item Type
Switch switch_binary switch_binary Switch Switch
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer
Scene Number scene_number scene_number   Number
Switch 1 switch_binary1 switch_binary Switch Switch
Dimmer 1 switch_dimmer1 switch_dimmer DimmableLight Dimmer
Switch 2 switch_binary2 switch_binary Switch Switch
Dimmer 2 switch_dimmer2 switch_dimmer DimmableLight Dimmer
Switch 3 switch_binary3 switch_binary Switch Switch
Dimmer 3 switch_dimmer3 switch_dimmer DimmableLight Dimmer
Switch 4 switch_binary4 switch_binary Switch Switch
Dimmer 4 switch_dimmer4 switch_dimmer DimmableLight Dimmer

Dimmer

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Dimmer 1

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Dimmer 2

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Dimmer 3

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Dimmer 4

Restore Last Value

Restore Last Dimming level on ON.

Property Value      
Configuration ID config_restoreLastValue      
Data Type BOOLEAN   Default Value true
Options Restore Last Value (true)      
  Restore Full Brightness (false)      

Device Configuration

The following table provides a summary of the configuration parameters available in the ZHC5010 FUGA Wall 4-way Switch with LED + Relay. Detailed information on each parameter can be found below.

Parameter Description
1: Upper paddle buttons mode Configuration of Pair Mode for the upper two buttons (button #1 and #2)
2: Lower paddle buttons mode Pair Mode, upper two buttons
3: LED indication #1 LED indication button 1
4: LED indication #2 LED indication button 2
5: LED indication #3 LED indication button 3
6: LED indication #4 LED indication button 4
7: Percentage of light in the LED #1 when On Configure the percentage of light in LED # 1, when the LED is turned on.
8: Percentage of light in the LED #2 when On Configure the percentage of light in LED # 2, when the LED is turned on.
9: Percentage of light in the LED #3 when On Configure the percentage of light in LED # 3, when the LED is turned on.
10: Percentage of light in the LED #4 when On Configure the percentage of light in LED #4, when the LED is turned on.
11: Percentage of light in the LED #1 when Off Configure the percentage of light in LED # 1, when the LED is turned off.
12: Percentage of light in the LED #2 when Off Configure the percentage of light in LED # 2, when the LED is turned off.
13: Percentage of light in the LED #3 when Off Configure the percentage of light in LED #3, when the LED is turned off.
14: Percentage of light in the LED #4 when Off Configure the percentage of light in LED #4, when the LED is turned off.
15: Relay mode How built-in relay is controlled
16: Indicator mode. set the current light level for the actual LED or the level value can be stored
17: Scene notification offset. Scene sequence numbers transmitted by Central Scene notifications.
18: Disable House Cleaning. Disable House Cleaning Mode.
19: Multilevel Switch (button #1) Disabled/Enabled Multilevel Switch on single press for device 1 (button #1)
19: Multilevel Switch - Upper switch value Multilevel Switch - Upper switch value - (button #1)
19: Multilevel Switch - Lower switch value Multilevel Switch - Lower switch value - (button #1)
20: Multilevel Switch (button #2) Disabled/Enabled Multilevel Switch on single press for device 2 (button #2)
20: Multilevel Switch - Upper switch value Multilevel Switch - Upper switch value - (button #2)
20: Multilevel Switch - Lower switch value Multilevel Switch - Lower switch value - (button #2)
21: Multilevel Switch (button #3) Disabled/Enabled Multilevel Switch on single press for device 3 (button #3)
21: Multilevel Switch - Upper switch value Multilevel Switch - Upper switch value - (button #3)
21: Multilevel Switch - Lower switch value Multilevel Switch - Lower switch value - (button #3)
22: Multilevel Switch (button #4) Disabled/Enabled Multilevel Switch on single press for device 4 (button #4)
22: Multilevel Switch - Upper switch value Multilevel Switch - Upper switch value - (button #4)
22: Multilevel Switch - Lower switch value Multilevel Switch - Lower switch value - (button #4)
23: Control of association groups (button #1). Control of association groups for device 1 (button #1).
24: Control of association groups (button #2). Control of association groups for device 2 (button #2).
25: Control of association groups (button #3). Control of association groups for device 3 (button #3).
26: Control of association groups (button #4). Control of association groups for device 4 (button #4).
1: Lifeline  
2: Send Basic Report (On/Off) when button #1 is used.  
3: Sends Basic Set (On/Off) when button #1 is used.  
4: Sends Binary Switch Set (On/Off) when button #1 is used.  
5: Send Binary Toggle Switch Set when button #1 is used.  
7: Send Basic Report (On/Off) when button #2 is used.  
8: Sends Basic Set (On/Off) when button #2 is used.  
9: Sends Binary Switch Set (On/Off) when button #2 is used.  
10: Send Binary Toggle Switch Set when button #2 is used.  
12: Send Basic Report (On/Off) when button #3 is used.  
13: Sends Basic Set (On/Off) when button #3 is used.  
14: Sends Binary Switch Set (On/Off) when button #3 is used.  
15: Send Binary Toggle Switch Set when button #3 is used.  
17: Send Basic Report (On/Off) when button #4 is used.  
18: Sends Basic Set (On/Off) when button #4 is used.  
19: Sends Binary Switch Set (On/Off) when button #4 is used  
20: Send Binary Toggle Switch Set when button #4 is used  

1: Upper paddle buttons mode

Configuration of Pair Mode for the upper two buttons (button #1 and #2)

Overview

0: Separate mode (toggle mode)

1: In pair mode, left side sends on/up commands, right side sends off/down commands

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 0
Options Separate mode (toggle mode). (0)      
  Pair mode (1)      

2: Lower paddle buttons mode

Pair Mode, upper two buttons

Overview

Configuration of Pair Mode for the upper two buttons (button #1 and #2).

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 0
Options Separate mode (toggle mode). (0)      
  Pair mode (1)      

3: LED indication #1

LED indication button 1

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 1
Options LED indication is disabled (0)      
  Indicates corresponding button (1)      
  Inverted indication (2)      
  Status of corresponding paddle (3)      
  Corresponding paddle, with inverted indication. (4)      
  Status of the built-in relay. (5)      
  Status of the built-in relay, inverted indication. (6)      
  5 seconds indication (7)      

4: LED indication #2

LED indication button 2

Property Value      
Configuration ID config_4_1      
Data Type INTEGER   Default Value 1
Options LED indication is disabled (0)      
  Indicates corresponding button (1)      
  Inverted indication (2)      
  Status of corresponding paddle (3)      
  Corresponding paddle, with inverted indication. (4)      
  Status of the built-in relay. (5)      
  Status of the built-in relay, inverted indication. (6)      
  5 seconds indication (7)      

5: LED indication #3

LED indication button 3

Property Value      
Configuration ID config_5_1      
Data Type INTEGER   Default Value 1
Options LED indication is disabled (0)      
  Indicates corresponding button (1)      
  Inverted indication (2)      
  Status of corresponding paddle (3)      
  Corresponding paddle, with inverted indication. (4)      
  Status of the built-in relay. (5)      
  Status of the built-in relay, inverted indication. (6)      
  5 seconds indication (7)      

6: LED indication #4

LED indication button 4

Property Value      
Configuration ID config_6_1      
Data Type INTEGER   Default Value 1
Options LED indication is disabled (0)      
  Indicates corresponding button (1)      
  Inverted indication (2)      
  Status of corresponding paddle (3)      
  Corresponding paddle, with inverted indication. (4)      
  Status of the built-in relay. (5)      
  Status of the built-in relay, inverted indication. (6)      
  5 seconds indication (7)      

7: Percentage of light in the LED #1 when On

Configure the percentage of light in LED # 1, when the LED is turned on.

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 0 to 100
Default Value 50

8: Percentage of light in the LED #2 when On

Configure the percentage of light in LED # 2, when the LED is turned on.

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 100
Default Value 50

9: Percentage of light in the LED #3 when On

Configure the percentage of light in LED # 3, when the LED is turned on.

Property Value
Configuration ID config_9_1
Data Type INTEGER
Range 0 to 100
Default Value 50

10: Percentage of light in the LED #4 when On

Configure the percentage of light in LED #4, when the LED is turned on.

Property Value
Configuration ID config_10_1
Data Type INTEGER
Range 0 to 100
Default Value 50

11: Percentage of light in the LED #1 when Off

Configure the percentage of light in LED # 1, when the LED is turned off.

Property Value
Configuration ID config_11_1
Data Type INTEGER
Range 0 to 100
Default Value 0

12: Percentage of light in the LED #2 when Off

Configure the percentage of light in LED # 2, when the LED is turned off.

Property Value
Configuration ID config_12_1
Data Type INTEGER
Range 0 to 100
Default Value 0

13: Percentage of light in the LED #3 when Off

Configure the percentage of light in LED #3, when the LED is turned off.

Property Value
Configuration ID config_13_1
Data Type INTEGER
Range 0 to 100
Default Value 0

14: Percentage of light in the LED #4 when Off

Configure the percentage of light in LED #4, when the LED is turned off.

Property Value
Configuration ID config_14_1
Data Type INTEGER
Range 0 to 100
Default Value 0

15: Relay mode

How built-in relay is controlled

Overview

This parameter configures which of the buttons that shall control the built-in relay, or if the relay only will be activated for one second, each time button #1 is used.

Property Value      
Configuration ID config_15_1      
Data Type INTEGER   Default Value 1
Options Relay is disabled. (0)      
  Relay is controlled by button #1 (1)      
  Relay is controlled by button #2 (2)      
  Relay is controlled by button #3 (3)      
  Relay is controlled by button #4 (4)      
  Relay is activated for one second, button #1 (5)      
  Relay is activated for half a second, button #2 (6)      
  Relay is activated for half a second, button #3 (7)      
  Relay is activated for half a second, button #4 (8)      
  Relay follows the state of button #1 (9)      
  Relay follows the state of button #2 (10)      
  Relay follows the state of button #3 (11)      
  Relay follows the state of button #4 (12)      
  Relay is only controlled by commands sent to the root device (13)      

16: Indicator mode.

set the current light level for the actual LED or the level value can be stored

Overview

When ZHC5010 receives an Indicator Set message, then the received value can be used only to set the current light level for the actual LED or the level value can be stored and will then be used for subsequent internal activations. 

Property Value      
Configuration ID config_16_1      
Data Type INTEGER   Default Value 1
Options Indicator Set level used to control the LED. (0)      
  Indicator Set level values and internal LED activations. (1)      

17: Scene notification offset.

Scene sequence numbers transmitted by Central Scene notifications.

Overview

Configure the scene sequence numbers that will be transmitted by Central Scene notifications.

Button #1 will send scene [value], button #2 will send scene [value] + 1, button #3 will send scene [value] + 2, button #4 will send scene [value] + 3. (Default = 1)

Property Value      
Configuration ID config_17_1      
Data Type INTEGER   Default Value 1
Options Scene notifications are turned off. (0)      
  Send scene value for button # (1)      

18: Disable House Cleaning.

Disable House Cleaning Mode.

Overview

This parameter is able to enable or disable the so-called “House Cleaning Mode”, where ZHC5010 is able send a dimming command in order to set the level of the lights to 100%.

Property Value      
Configuration ID config_18_1      
Data Type INTEGER   Default Value 0
Options House Cleaning Mode is enabled (0)      
  1 House Cleaning Mode is disabled. (1)      

19: Multilevel Switch (button #1) Disabled/Enabled

Multilevel Switch on single press for device 1 (button #1)

Property Value      
Configuration ID config_19_4_00000001      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

19: Multilevel Switch - Upper switch value

Multilevel Switch - Upper switch value - (button #1)

Overview

When single pressing the button for ON, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 255)

Property Value
Configuration ID config_19_4_0000FF00
Data Type INTEGER
Range 0 to 255
Default Value 255

19: Multilevel Switch - Lower switch value

Multilevel Switch - Lower switch value - (button #1)

Overview

When single pressing the button for OFF, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 0)

Property Value
Configuration ID config_19_4_00FF0000
Data Type INTEGER
Range 0 to 99
Default Value 0

20: Multilevel Switch (button #2) Disabled/Enabled

Multilevel Switch on single press for device 2 (button #2)

Property Value      
Configuration ID config_20_4_00000001      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

20: Multilevel Switch - Upper switch value

Multilevel Switch - Upper switch value - (button #2)

Overview

When single pressing the button for ON, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 255)

Property Value
Configuration ID config_20_4_0000FF00
Data Type INTEGER
Range 0 to 255
Default Value 255

20: Multilevel Switch - Lower switch value

Multilevel Switch - Lower switch value - (button #2)

Overview

When single pressing the button for OFF, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 0)

Property Value
Configuration ID config_20_4_00FF0000
Data Type INTEGER
Range 0 to 99
Default Value 0

21: Multilevel Switch (button #3) Disabled/Enabled

Multilevel Switch on single press for device 3 (button #3)

Property Value      
Configuration ID config_21_4_00000001      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

21: Multilevel Switch - Upper switch value

Multilevel Switch - Upper switch value - (button #3)

Overview

When single pressing the button for ON, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 255)

Property Value
Configuration ID config_21_4_0000FF00
Data Type INTEGER
Range 0 to 255
Default Value 255

21: Multilevel Switch - Lower switch value

Multilevel Switch - Lower switch value - (button #3)

Overview

When single pressing the button for OFF, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 0)

Property Value
Configuration ID config_21_4_00FF0000
Data Type INTEGER
Range 0 to 99
Default Value 0

22: Multilevel Switch (button #4) Disabled/Enabled

Multilevel Switch on single press for device 4 (button #4)

Property Value      
Configuration ID config_22_4_00000001      
Data Type INTEGER   Default Value 1
Options Disabled (0)      
  Enabled (1)      

22: Multilevel Switch - Upper switch value

Multilevel Switch - Upper switch value - (button #4)

Overview

When single pressing the button for ON, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 255)

Property Value
Configuration ID config_22_4_0000FF00
Data Type INTEGER
Range 0 to 255
Default Value 255

22: Multilevel Switch - Lower switch value

Multilevel Switch - Lower switch value - (button #4)

Overview

When single pressing the button for OFF, a Multilevel Switch Set with this value will be send to devices in association group 6. (Default = 0)

Property Value
Configuration ID config_22_4_00FF0000
Data Type INTEGER
Range 0 to 99
Default Value 0

23: Control of association groups (button #1).

Control of association groups for device 1 (button #1).

Overview

Enable or disable if received commands are relayed to the nodes in the association groups.

Property Value      
Configuration ID config_23_1      
Data Type INTEGER   Default Value 1
Options Association groups will not be switched. (0)      
  Association groups will be switched, (1)      

24: Control of association groups (button #2).

Control of association groups for device 2 (button #2).

Overview

Enable or disable if received commands are relayed to the nodes in the association groups.

Property Value      
Configuration ID config_24_1      
Data Type INTEGER   Default Value 1
Options Association groups will not be switched. (0)      
  Association groups will be switched, (1)      

25: Control of association groups (button #3).

Control of association groups for device 3 (button #3).

Overview

Enable or disable if received commands are relayed to the nodes in the association groups.

Property Value      
Configuration ID config_25_1      
Data Type INTEGER   Default Value 1
Options Association groups will not be switched. (0)      
  Association groups will be switched, (1)      

26: Control of association groups (button #4).

Control of association groups for device 4 (button #4).

Overview

Enable or disable if received commands are relayed to the nodes in the association groups.

Property Value      
Configuration ID config_26_1      
Data Type INTEGER   Default Value 1
Options Association groups will not be switched. (0)      
  Association groups will be switched, (1)      

1: Lifeline

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Send Basic Report (On/Off) when button #1 is used.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Sends Basic Set (On/Off) when button #1 is used.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

4: Sends Binary Switch Set (On/Off) when button #1 is used.

Property Value
Configuration ID group_4
Data Type TEXT
Range to

5: Send Binary Toggle Switch Set when button #1 is used.

Property Value
Configuration ID group_5
Data Type TEXT
Range to

7: Send Basic Report (On/Off) when button #2 is used.

Property Value
Configuration ID group_7
Data Type TEXT
Range to

8: Sends Basic Set (On/Off) when button #2 is used.

Property Value
Configuration ID group_8
Data Type TEXT
Range to

9: Sends Binary Switch Set (On/Off) when button #2 is used.

Property Value
Configuration ID group_9
Data Type TEXT
Range to

10: Send Binary Toggle Switch Set when button #2 is used.

Property Value
Configuration ID group_10
Data Type TEXT
Range to

12: Send Basic Report (On/Off) when button #3 is used.

Property Value
Configuration ID group_12
Data Type TEXT
Range to

13: Sends Basic Set (On/Off) when button #3 is used.

Property Value
Configuration ID group_13
Data Type TEXT
Range to

14: Sends Binary Switch Set (On/Off) when button #3 is used.

Property Value
Configuration ID group_14
Data Type TEXT
Range to

15: Send Binary Toggle Switch Set when button #3 is used.

Property Value
Configuration ID group_15
Data Type TEXT
Range to

17: Send Basic Report (On/Off) when button #4 is used.

Property Value
Configuration ID group_17
Data Type TEXT
Range to

18: Sends Basic Set (On/Off) when button #4 is used.

Property Value
Configuration ID group_18
Data Type TEXT
Range to

19: Sends Binary Switch Set (On/Off) when button #4 is used

Property Value
Configuration ID group_19
Data Type TEXT
Range to

20: Send Binary Toggle Switch Set when button #4 is used

Property Value
Configuration ID group_20
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.