The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZIP-PAB01 Zipato Micromodule Energy Meter

This describes the Z-Wave device ZIP-PAB01, manufactured by Philio Technology Corp with the thing type UID of philio_pab01_00_000.

ZIP-PAB01 product image

The ZIP-PAB01 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the ZIP-PAB01 -:

Channel Channel Id Category Item Type
Intensty meter 0 (amps) meter_current Energy Number
Power factor 0 meter_powerfactor Energy Number
Power meter 0 (watts) meter_watts Energy Number
Electric meter (kWh) meter_kwh Energy Number
Line voltage (volts) meter_voltage Energy Number
Intensity meter 1 (amps) meter_current1 Energy Number
Power factor meter 1 meter_powerfactor1 Energy Number
Power meter 1 (watts) meter_watts1 Energy Number
Energy meter 1 (kWh) meter_kwh1 Energy Number
Line voltage (volts) meter_voltage1 Energy Number
Intensity meter 2 (amps) meter_current2 Energy Number
power factor 2 meter_powerfactor2 Energy Number
Power meter 2 (watts) meter_watts2 Energy Number
Energy meter 2 (kWh) meter_kwh2 Energy Number
Line voltage 2 (volts) meter_voltage2 Energy Number
Intensity meter 3 (amps) meter_current3 Energy Number
Power factor 3 meter_powerfactor3 Energy Number
Power meter 3 (watts) meter_watts3 Energy Number
Energy meter 3 (kWh) meter_kwh3 Energy Number
Voltage 3 (volts) meter_voltage3 Energy Number

Intensty meter 0 (amps)

Indicates the instantaneous current consumption.

The meter_current channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power factor 0

Indicates the instantaneous power factor.

The meter_powerfactor channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power meter 0 (watts)

Indicates the instantaneous power consumption.

The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh)

Indicates the energy consumption (kWh).

The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Line voltage (volts)

Indicates the instantaneous voltage.

The meter_voltage channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Intensity meter 1 (amps)

Indicates the instantaneous current consumption.

The meter_current1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power factor meter 1

Indicates the instantaneous power factor.

The meter_powerfactor1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power meter 1 (watts)

Indicates the instantaneous power consumption.

The meter_watts1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Energy meter 1 (kWh)

Indicates the energy consumption (kWh).

The meter_kwh1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Line voltage (volts)

Indicates the instantaneous voltage.

The meter_voltage1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Intensity meter 2 (amps)

Indicates the instantaneous current consumption.

The meter_current2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

power factor 2

Indicates the instantaneous power factor.

The meter_powerfactor2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power meter 2 (watts)

Indicates the instantaneous power consumption.

The meter_watts2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Energy meter 2 (kWh)

Indicates the energy consumption (kWh).

The meter_kwh2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Line voltage 2 (volts)

Indicates the instantaneous voltage.

The meter_voltage2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Intensity meter 3 (amps)

Indicates the instantaneous current consumption.

The meter_current3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power factor 3

Indicates the instantaneous power factor.

The meter_powerfactor3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Power meter 3 (watts)

Indicates the instantaneous power consumption.

The meter_watts3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Energy meter 3 (kWh)

Indicates the energy consumption (kWh).

The meter_kwh3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Voltage 3 (volts)

Indicates the instantaneous voltage.

The meter_voltage3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Device Configuration

The following table provides a summary of the 3 configuration parameters available in the ZIP-PAB01. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Power meter report period Power meter report period, in 5 seconds unit. 720 -> 1 hour
2 Energy meter report period The accumulated power consumption report period
3 Selected default endpoint 1 => CT1 and CT2, 2 => CT1, 3 => CT2

Parameter 1: Power meter report period

Power meter report period, in 5 seconds unit. 720 -> 1 hour If the setting is configured for 1 hour (set value 720), the module will report its instant power consumption every 1 hour to the node of the corresponding group. The maximum interval to report its instant power consumption is 45h (5s * 32767 / 3600 = 45h) Values in the range 1 to 32767 may be set.

The manufacturer defined default value is 720.

This parameter has the configuration ID config_1_2 and is of type INTEGER.

Parameter 2: Energy meter report period

The accumulated power consumption report period If the setting is configured for 1 hour (set value 720), the module will report its accumulated power consumption every 1 hour to the node of the corresponding group. The maximum interval to report its accumulated power consumption is 45h (5s * 32767 / 3600 = 45h) Values in the range 1 to 32767 may be set.

The manufacturer defined default value is 720.

This parameter has the configuration ID config_2_2 and is of type INTEGER.

Parameter 3: Selected default endpoint

1 => CT1 and CT2, 2 => CT1, 3 => CT2 If Controller does not use Multi Channel command class to access the endpoint of the module, you may configure the endpoint that will react to the Basic Command Class, Binary Switch command class or Meter command class V3. Values in the range 1 to 3 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZIP-PAB01 supports 3 association groups.

Group 1: CT1 and CT2

Sum of CT1 and CT2 This group supports 1 nodes.

Group 2: CT1

Data from CT1 This group supports 1 nodes.

Group 3: CT2

Data from CT2 This group supports 1 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_METER_V3| | | COMMAND_CLASS_CRC_16_ENCAP_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_POWERLEVEL_V1| | | COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_METER_V3| | | COMMAND_CLASS_MULTI_CHANNEL_V2| |

Endpoint 2

| Command Class | Comment | |—————|———| | COMMAND_CLASS_METER_V3| |

Endpoint 3

Command Class Comment
COMMAND_CLASS_METER_V3  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.