The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

PSP05 Motion Sensor

This describes the Z-Wave device PSP05, manufactured by Philio Technology Corp with the thing type UID of philio_psp05_00_000.

The device is in the category of Sensor, defining Device used to measure something.

PSP05 product image

The PSP05 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

The PSP05 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the PSP05 -:

Channel Channel Id Category Item Type
Binary Sensor sensor_binary Door Switch
Alarm (burglar) alarm_burglar Door Switch
Battery Level battery-level Battery Number

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Alarm (burglar)

Indicates if the burglar alarm is triggered.

The alarm_burglar channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 9 configuration parameters available in the PSP05. Detailed information on each parameter can be found in the sections below.

Param Name Description
3 PIR Sensitivity Adjust the PIR Sensitivity
7 Motion OFF Reporting Sends notification when motion has completed.
7 Notification Type Method used to send notifications on motion
7 Send Multi CC in auto report Send Multi CC in auto report
7 Send Battery Report when Triggered Whether or not a battery status report should be sent when triggered
8 Re-detection interval Multiples of 8 seconds to wait before re-detection
9 Turn off light time Time to wait after lighting has been turned on before turning off again
10 Batery level reporting interval How frequently battery status should be reported
20 Tick Interval Interval time for sending reports
  Wakeup Interval Sets the interval at which the device will accept commands from the controller
  Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 3: PIR Sensitivity

Adjust the PIR Sensitivity This setting sets the sensitivity of the PIR (motion) sensor. A setting of 0 (zero) will disable the sensor, with 99 being the highest level of sensitivity. The default sensitivity setting is 80.

The higher the sensitivity, the greater the range of detection (things farther away will trigger the sensor). However, this may also result in things that are nearer triggering the sensor too frequently. Values in the range 0 to 99 may be set.

The manufacturer defined default value is 80.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 7: Motion OFF Reporting

Sends notification when motion has completed. Sends notification when motion has completed. The following option values may be configured -:

Value Description
0 Don’t Send Report
1 Send Report

The manufacturer defined default value is 0 (Don’t Send Report).

This parameter has the configuration ID config_7_1_00000010 and is of type INTEGER.

Parameter 7: Notification Type

Method used to send notifications on motion Indicates method used to send notifications in the event of motion being triggered. Either Binary Sensor or Notification The following option values may be configured -:

Value Description
0 Report Notification
1 Binary Sensor

The manufacturer defined default value is 0 (Report Notification).

This parameter has the configuration ID config_7_1_00001000 and is of type INTEGER.

Parameter 7: Send Multi CC in auto report

Send Multi CC in auto report Investigation required to determine purpose of this. The following option values may be configured -:

Value Description
0 Disable
1 Enable

The manufacturer defined default value is 0 (Disable).

This parameter has the configuration ID config_7_1_00010000 and is of type INTEGER.

Parameter 7: Send Battery Report when Triggered

Whether or not a battery status report should be sent when triggered

The following option values may be configured -:

Value Description
0 Enable
1 Disable

The manufacturer defined default value is 0 (Enable).

This parameter has the configuration ID config_7_1_00100000 and is of type INTEGER.

Parameter 8: Re-detection interval

Multiples of 8 seconds to wait before re-detection By default, the sensor will wait 24 seconds (3 x 8) after detecting motion before it will send a further detection report. This value can be increased to a maximum of 127 (which is 127 * 8), meaning the re-detection interval will be 1,016 seconds (~17 minutes). The minimum value is 1 (1 * 8), meaning a re-detection interval of 8 seconds.

The default is a value of 3, meaning a re-detection interval of 24 seconds. Values in the range 1 to 127 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: Turn off light time

Time to wait after lighting has been turned on before turning off again Number of seconds (in multiples of 8) to wait before turning off lights that were turned on as a result of motion occurring. A default value of 4 means (4 x 8) 32 seconds later, lights will be turned off.

This setting should only be used when you are using association groups to control lighting events. If you are controlling on/off events as a result of motion through independent rules, this setting is irrelevant. Values in the range 0 to 127 may be set.

The manufacturer defined default value is 4.

This parameter has the configuration ID config_9_1 and is of type INTEGER.

Parameter 10: Batery level reporting interval

How frequently battery status should be reported The frequency (in multiples of ‘Tick Time’) that the device should send battery status reports. If set to 0, battery status reports are not sent.

The default ‘tick time’ (see other parameter settings) is 30, meaning 30 minutes. The default value of this parameter is 12, meaning that a battery report will be sent every 6 hours (12 * 30 minutes). Values in the range 0 to 127 may be set.

The manufacturer defined default value is 12.

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 20: Tick Interval

Interval time for sending reports This setting is used by the battery reporting interval setting. This setting defines the ‘tick interval’ or the number of time blocks to wait between sending reports. The default value of 30 means that a tick interval is 30 minutes. Values in the range 0 to 127 may be set.

The manufacturer defined default value is 30.

This parameter has the configuration ID config_20_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The PSP05 supports 2 association groups.

Group 1: Lifeline

The group 1 is for receiving the report message This group supports 8 nodes.

Group 2: Basic Set

The group 2 is for light control This group supports 8 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SENSOR_BINARY_V2  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_ALARM_V4  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_WAKE_UP_V2  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  
COMMAND_CLASS_MULTI_CMD_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.