The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

Danalock V3-BTZE Z-Wave controlled door lock with Bluetooth Smart

This describes the Z-Wave device Danalock V3-BTZE, manufactured by Poly-control with the thing type UID of polycontrol_btze_00_000.

The device is in the category of Lock, defining Devices whose primary pupose is locking something.

Danalock V3-BTZE product image

The Danalock V3-BTZE supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.

Overview

Danalock supports:
- S0/S2 Z-Wave Security
- Bluetooth Smart
- Twist Assist
- Auto Lock
- Hold And Release
- Back To Back

Inclusion Information

To add or include the Danalock into a Z-Wave network

  1. Set the controller in inclusion mode
  2. Push the switch once.
  3. Wait 5 seconds.

Exclusion Information

To remove or exclude the Danalock into a Z-Wave network

  1. Set the controller in exclusion mode
  2. Push the switch once.
  3. Wait 5 seconds.

Channels

The following table summarises the channels available for the Danalock V3-BTZE -:

Channel Channel Id Category Item Type
Door Lock lock_door Door Switch
Battery Level battery-level Battery Number

Door Lock

Lock and unlock the door.

The lock_door channel supports the Switch item and is in the Door category.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The battery-level channel supports the Number item and is in the Battery category.

Device Configuration

The following table provides a summary of the 6 configuration parameters available in the Danalock V3-BTZE. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Twin Assist Helps you to lock and unlock your door lock.
2 Hold and Release After a unlock operation the lock holds the lock, so the door can be opened
3 Block to block The lock will run the motor until it hits resistance.
4 BLE Temporary Allowed The BLE is enabled for a number of seconds.
5 BLE Always Allowed BLE Always Allowed
6 Autolock Lock after an unlock.Value is delay in sec before lock is locked again.
  Lock Timeout Sets the time after which the door will auto lock

Parameter 1: Twin Assist

Helps you to lock and unlock your door lock. 0 -> disabled

1 -> enabled The following option values may be configured -:

Value Description
0 disabled
1 enabled

The manufacturer defined default value is 0 (disabled).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Hold and Release

After a unlock operation the lock holds the lock, so the door can be opened 0 -> disabled

1 to 2147483647 -> enabled no. of seconds The following option values may be configured, in addition to values in the range 0 to 2147483647 -:

Value Description
0 Disabled

The manufacturer defined default value is 0 (Disabled).

This parameter has the configuration ID config_2_4 and is of type INTEGER.

Parameter 3: Block to block

The lock will run the motor until it hits resistance.

The following option values may be configured -:

Value Description
0 Disabled
1 Enabled

The manufacturer defined default value is 0 (Disabled).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: BLE Temporary Allowed

The BLE is enabled for a number of seconds. 0 -> Disabled

1 to 2147483647 -> enabled no. of seconds Values in the range 0 to 2147483647 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_4_4 and is of type INTEGER.

Parameter 5: BLE Always Allowed

BLE Always Allowed 0 -> BLE Always disabled

1 -> BLE Always enabled The following option values may be configured -:

Value Description
0 BLE Always disabled
1 BLE Always enabled

The manufacturer defined default value is 0 (BLE Always disabled).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 6: Autolock

Lock after an unlock.Value is delay in sec before lock is locked again. 0 -> disabled

1 to 2147483647 -> enabled no. of seconds Values in the range 0 to 2147483647 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_6_4 and is of type INTEGER.

Lock Timeout

Sets the time after which the door will auto lock.

This parameter has the configuration ID doorlock_timeout and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The Danalock V3-BTZE supports 1 association group.

Group 1: Lifeline

Z-Wave Plus Lifeline This group supports 1 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V2  
COMMAND_CLASS_DOOR_LOCK_V2  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4  
COMMAND_CLASS_BATTERY_V1  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  
COMMAND_CLASS_SECURITY_V1  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.