BTZW125 Danalock v2 circle

This describes the Z-Wave device BTZW125, manufactured by Poly-control with the thing type UID of polycontrol_btzu125_00_000.

Danalock v2 circle

Channels

The following table summarises the channels available for the BTZW125 Danalock v2 circle.

Channel Channel Id Channel Type UID Category Item Type
Door Lock lock_door lock_door Door Switch
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the BTZW125 Danalock v2 circle. Detailed information on each parameter can be found below.

Parameter Description
1: Direction Direction
2: Speed (Torque) Speed (Torque)
3: Mode Mode
4: Turn degrees Turn degrees
5: Auto Latch time Auto Latch time
6: Sound Sound
7: Battery Type Battery Type
8: Battery alarm Battery alarm value
9: TurnAndGo TurnAndGo
10: BrakeAndGoBack Turn 75 degrees back after x seconds
11: Async Used if the lock is using an optional rotation sensor
12: ReportType Door lock operation report type
1: LifeLine Z-Wave Plus Lifeline

1: Direction

Direction

Overview

0 -> The motor goes clockwise when latched

1 -> The motor goes counterclockwise when latched

Property Value      
Configuration ID config_1_1      
Data Type INTEGER   Default Value 0
Options Clockwise (0)      
  The motor goes counterclockwise when latched (1)      

2: Speed (Torque)

Speed (Torque)

Overview

1 -> Slowest

2 -> Slow

3 -> (Default) Normal

4 -> Fast

5 -> Fastest

Property Value      
Configuration ID config_2_1      
Data Type INTEGER   Default Value 3
Options Slowest (1)      
  Slow (2)      
  Normal (3)      
  Fast (4)      
  Fastest (5)      

3: Mode

Mode

Overview

0 -> Stepper motor mode wave drive(power saving)

1 -> (Default) Stepper motor mode full drive(Normal)

2 -> Relay mode

Property Value      
Configuration ID config_3_1      
Data Type INTEGER   Default Value 1
Options Powersaving (0)      
  Full drive (1)      
  Relay mode (2)      

4: Turn degrees

Turn degrees

Overview

(Default) Factor 10 turn degrees ( 1 = 10 degrees, 9 = 90 degrees etc.)

Property Value
Configuration ID config_4_1
Data Type INTEGER
Range 1 to 100
Default Value 1

5: Auto Latch time

Auto Latch time

Overview

How many seconds from the lock has been unlatched to it automatically should close again. If 0 then it is disabled.

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 0 to 60
Default Value 0

6: Sound

Sound

Overview

Enable the beep sound from latch or unlatch operations

Property Value      
Configuration ID config_6_1      
Data Type INTEGER   Default Value 1
Options Disable sound (0)      
  Enable Sound (1)      

7: Battery Type

Battery Type

Overview

2 -> Mains power, changing from and to mains power requires the Danalock to be excluded and included.

0 -> 3,6 Volt battery

1 -> (Default) 3.0 Volt battery.

Property Value      
Configuration ID config_7_1      
Data Type INTEGER   Default Value 1
Options 3,6V (0)      
  3,0V (1)      
  Mains power (2)      

8: Battery alarm

Battery alarm value

Overview

When the battery level is under this value, the device will notify user with a beep sound after latch or unlatch

Property Value
Configuration ID config_8_1
Data Type INTEGER
Range 0 to 100
Default Value 0

9: TurnAndGo

TurnAndGo

Overview

using a optional rotation sensor. Latch&Go on will turn automatically when manual turn is detected.

Property Value      
Configuration ID config_9_1      
Data Type INTEGER   Default Value 0
Options Off (0)      
  On (1)      

10: BrakeAndGoBack

Turn 75 degrees back after x seconds

Overview

0 -> (Default) Disabled

1 to 15 -> Seconds to brake. When used the lock will brake for x amount of seconds and then turn 75 degrees back. Made for special doors without door lever.(Only when unlatching).

Property Value      
Configuration ID config_10_1      
Data Type INTEGER   Default Value 0
Options Disabled (0)      
  1 second (1)      
  Brake for 2 seconds (2)      
  Brake for 3 seconds (3)      
  Brake for 4 seconds (4)      
  Brake for 5 seconds (5)      
  Brake for 6 seconds (6)      
  Brake for 7 seconds (7)      
  Brake for 8 seconds (8)      
  Brake for 9 seconds (9)      
  Brake for 10 seconds (10)      
  Brake for 11 seconds (11)      
  Brake for 12 seconds (12)      
  Brake for 13 seconds (13)      
  Brake for 14 seconds (14)      
  Brake for 15 seconds (15)      

11: Async

Used if the lock is using an optional rotation sensor

Overview

0 -> (Default) Async off

1 -> Async on. Used if the lock is using an optional rotation sensor. When async is enabled the lock will auto calibrate if already unlatched and asked to Unlatch again (used for special door locks where the key turn is asynced from the inside nob.)

Property Value      
Configuration ID config_11_1      
Data Type INTEGER   Default Value 0
Options Async off (0)      
  Async on (1)      

12: ReportType

Door lock operation report type

Overview

Door lock operation report type

2 -> No Door lock operation reports are sent unsolicited.

0 -> (Default) Simple supported by all controllers that support door locks.

1 -> Advanced, more specific reports through notification Command Class.

Property Value      
Configuration ID config_12_1      
Data Type INTEGER   Default Value 0
Options Default (0)      
  Advanced (1)      
  No reporting (2)      

1: LifeLine

Z-Wave Plus Lifeline

Property Value
Configuration ID group_1
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.