POPE700168 POPP Rain-Sensor

This describes the Z-Wave device POPE700168, manufactured by Popp & Co with the thing type UID of popp_pope700168_00_000.

POPP Rain-Sensor

Channels

The following table summarises the channels available for the POPE700168 POPP Rain-Sensor.

Channel Channel Id Channel Type UID Category Item Type
Basic value basic_number basic_number    
Sensor (general) sensor_general sensor_general   Number
Sensor (rain rate) sensor_rainrate sensor_rainrate Humidity Number
Water meter (amps) meter_water_cubic_meters meter_water_cubic_meters Energy Number
  battery-level system.battery-level    

Device Configuration

The following table provides a summary of the configuration parameters available in the POPE700168 POPP Rain-Sensor. Detailed information on each parameter can be found below.

Parameter Description
1: Rain Counter Ths values shows the total count of rain from the moment of inclusion in mm waterlevel. By…
2: Rain Start Command This BASIC Set Command value is sent out into Association Group 2 when the device detects …
3: Rain Stop Command This BASIC Set Command value is sent out into Association Group 2 when the device detects …
4: Meter Multiplier This multiplier allows to adapt the display to certain controllers not being able to handl…
5: Heavy Rain This threshold defines when a heavy rain condition is hit. In most countries this is defin…
6: Heavy Rain Start Command This BASIC Set Command value is sent out into Association Group 3 when the device detects …
7: Heavy Rain Stop Command This BASIC Set Command value is sent out into Association Group 3 when the device detects …
1: Lifeline  
2: Switching Command when Rain (> 0 mm/h) Switching Command when Rain (> 0 mm/h). Basic Set Comand is sent.
3: Heavy Rain detected. Basic Set Comand is sent.  

1: Rain Counter

Ths values shows the total count of rain from the moment of inclusion in mm waterlevel. By writing this value this counter can be reset. Size: 2 Byte, Default Value: 0

Property Value
Configuration ID config_1_2
Data Type INTEGER
Range 0 to 32000
Default Value 0

2: Rain Start Command

This BASIC Set Command value is sent out into Association Group 2 when the device detects start of rain Size: 1 Byte, Default Value: 99

Property Value
Configuration ID config_2_1
Data Type INTEGER
Range 0 to 99
Default Value 99

3: Rain Stop Command

This BASIC Set Command value is sent out into Association Group 2 when the device detects stop of rain Size: 1 Byte, Default Value: 0

Property Value
Configuration ID config_3_1
Data Type INTEGER
Range 0 to 99
Default Value 0

4: Meter Multiplier

This multiplier allows to adapt the display to certain controllers not being able to handle very low numbers. Size: 2 Byte, Default Value: 1 only 1/10/100/1000

Property Value
Configuration ID config_4_2
Data Type INTEGER
Range 1 to 1000
Default Value 1

5: Heavy Rain

This threshold defines when a heavy rain condition is hit. In most countries this is defined as > 15 mm rain per hour. The default value however is to turn this function off. Size: 1 Byte, Default Value: 255

Property Value
Configuration ID config_5_1
Data Type INTEGER
Range 0 to 255
Default Value 255

6: Heavy Rain Start Command

This BASIC Set Command value is sent out into Association Group 3 when the device detects start of heavy rain Size: 1 Byte, Default Value: 99

Property Value
Configuration ID config_6_1
Data Type INTEGER
Range 0 to 99
Default Value 99

7: Heavy Rain Stop Command

This BASIC Set Command value is sent out into Association Group 3 when the device detects stop of heavy rain Size: 1 Byte, Default Value: 0

Property Value
Configuration ID config_7_1
Data Type INTEGER
Range 0 to 99
Default Value 0

1: Lifeline

Property Value
Configuration ID group_1
Data Type TEXT
Range to

2: Switching Command when Rain (> 0 mm/h)

Switching Command when Rain (> 0 mm/h). Basic Set Comand is sent.

Property Value
Configuration ID group_2
Data Type TEXT
Range to

3: Heavy Rain detected. Basic Set Comand is sent.

Property Value
Configuration ID group_3
Data Type TEXT
Range to

Did you spot an error in the above definition or want to improve the content? You can edit the database here.