The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZMNHAD Flush 1 relay

This describes the Z-Wave device ZMNHAD, manufactured by Goap with the thing type UID of qubino_zmnhad_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

ZMNHAD product image

The ZMNHAD supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

This Z-Wave module is used for switching on or off the electrical device (e.g. light or fan). The module can be controlled either through Z-wave network or through the wall switch. The module is designed to be mounted inside a “flush mounting box”, hidden behind a traditional wall switch. Module measures power consumption of electrical device and supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-wave network. Supported switches Module supports mono-stable switches (push button) and bi-stable switches. The module is factory set to operate with bi-stable switches.

Inclusion Information

Module Inclusion (Adding to Z-Wave network)

  • Connect module to power supply (with temperature sensor connected -if purchased)
  • Enable add/remove mode on main controller
  • Auto-inclusion (works forabout 5 seconds after connected to power supply) or
  • Press push button I1 three times within 3s (3 times change switch state within 3 seconds) or
  • Press service button S (only applicable for 24 V SELV supply voltage) for more than 2 seconds.

NOTE1: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply.

NOTE2: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply , connect the sensor and re-include the module.

Exclusion Information

Module Exclusion/Reset (Removing from Z-Wavenetwork)

  • Connect module to power supply
  • Bring module within maximum 1 meter (3 feet) of the main controller,
  • Enable add/remove mode on main controller,
  • Press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or
  • Press service button S (only applicable for 24 V SELV supply voltage) for more than 6 seconds.

By this function all parameters of the module are set to default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service button S is pressed more than 2 and less than 6 seconds) module is excluded, but configuration parameters are not set to default values.

Channels

The following table summarises the channels available for the ZMNHAD -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Binary Sensor sensor_binary Door Switch
Electric meter (watts) meter_watts Energy Number
Electric meter (kWh) meter_kwh Energy Number
Alarm (power) alarm_power Door Switch
Switch 1 switch_binary1 Switch Switch
Electric meter (watts) 1 meter_watts1 Energy Number
Electric meter (kWh) 1 meter_kwh1 Energy Number
Binary Sensor I2 sensor_binary2 Door Switch
Alarm (power) 2 alarm_power2 Door Switch
Binary Sensor I3 sensor_binary3 Door Switch
Sensor (temperature) sensor_temperature3 Temperature Number
Sensor (temperature) sensor_temperature4 Temperature Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Binary Sensor

Indicates if a sensor has triggered.

The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Electric meter (watts)

Indicates the instantaneous power consumption.

The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh)

Indicates the energy consumption (kWh).

The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Alarm (power)

Indicates if a power alarm is triggered.

The alarm_power channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Switch 1

Switch the power on and off.

The switch_binary1 channel supports the Switch item and is in the Switch category.

Electric meter (watts) 1

Indicates the instantaneous power consumption.

The meter_watts1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (kWh) 1

Indicates the energy consumption (kWh).

The meter_kwh1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Binary Sensor I2

Indicates if a sensor has triggered.

The sensor_binary2 channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Alarm (power) 2

Indicates if a power alarm is triggered.

The alarm_power2 channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF Ok
ON Alarm

Binary Sensor I3

Indicates if a sensor has triggered.

The sensor_binary3 channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
ON Triggered
OFF Untriggered

Sensor (temperature)

Indicates the current temperature.

The sensor_temperature3 channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Sensor (temperature)

Indicates the current temperature.

The sensor_temperature4 channel supports the Number item and is in the Temperature category. This is a read only channel so will only be updated following state changes from the device.

Device Configuration

The following table provides a summary of the 15 configuration parameters available in the ZMNHAD. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Input 1 switch type Input 1 switch type
2 Input 2 contact type Input 2 contact type
3 Input 3 contact type Input 3 contact type
10 Activate / deactivate functions ALL ON/ALL OFF Flush 1 relay module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
11 Automatic turning off relay after set time When relay is ON it goes automatically OFF after time defined by this parameter. Timer is reset to zero each time the module receive ON command regardless from where it comes (push button, associated module, controller,..). 0 - Auto OFF disabled. 1
12 Automatic turning on relay after set time When relay is OFF it goes automatically ON after time defined by this parameter. Timer is reset to zero each time the module receive OFF command regardless from where it comes (push button, associated module, controller,..). 0 - Auto ON disabled. 1 –
15 Automatic turning off / on seconds or milliseconds selection NOTE: Parameter is the same for turning OFF or ON.
30 Saving the state of the relay after a power failure Saving the state of the relay after a power failure
40 Power reporting in Watts on power change 0 – Reporting Disabled 1 – 100 = 1% - 100% Reporting enabled Power report is send (push) only when actual power in Watts in real time change for more than set percentage comparing to previous actual power in Watts, step is 1%. NOTE: If power chan
42 Power reporting in Watts on power change Set value means time interval (0 – 32535) in seconds, when power report is send. Default value 300 (power report in Watts is send each 300s) 0 – Reporting Disabled 1 – 32535 = 1second – 32535 seconds. Reporting enabled. Power report is send with time
63 Output Switch selection Set value means the type of the device that is connected to the output. The device type can be normally open (NO) or normally close (NC).
100 Enable / Disable Endpoints I2 or select Notification Type and Event Enabling I2 means that Endpoint (I2) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. Endpoint device type selec
101 Enable / Disable Endpoints I3 or select Notification Type and Event Enabling I3 means that Endpoint (I3) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. Endpoint device type selec
110 Temperature sensor offset settings Set value is added or subtracted to actual measured value by sensor. 32536 – offset is 0.0C From 1 to 100–value from 0.1°C to 10.0°C is added to actual measured temperature. From 1001 to 1100 – value from -0.1 °C to -10.0 °C is subtracted to actual mea
120 Digital temperature sensor reporting If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter.0 – Reporting disabled1- 127 = 0,1°C – 12,7°C, step is 0,1°C
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Input 1 switch type

Input 1 switch type

The following option values may be configured -:

Value Description
0 mono-stable switch type (push button)
1 bi-stable switch type

The manufacturer defined default value is 1 (bi-stable switch type).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Input 2 contact type

Input 2 contact type

The following option values may be configured -:

Value Description
0 NO (normaly open) input type
1 NC (normaly close) input type

The manufacturer defined default value is 0 (NO (normaly open) input type).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Input 3 contact type

Input 3 contact type

The following option values may be configured -:

Value Description
0 NO (normaly open) input type
1 NC (normaly close) input type

The manufacturer defined default value is 0 (NO (normaly open) input type).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 10: Activate / deactivate functions ALL ON/ALL OFF

Flush 1 relay module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.

The following option values may be configured -:

Value Description
0 ALL ON is not active ALL OFF is not active
1 ALL ON is not active ALL OFF active
2 ALL ON active ALL OFF is not active
255 ALL ON active, ALL OFF active

The manufacturer defined default value is 255 (ALL ON active, ALL OFF active).

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 11: Automatic turning off relay after set time

When relay is ON it goes automatically OFF after time defined by this parameter. Timer is reset to zero each time the module receive ON command regardless from where it comes (push button, associated module, controller,..). 0 - Auto OFF disabled. 1

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_11_2 and is of type INTEGER.

Parameter 12: Automatic turning on relay after set time

When relay is OFF it goes automatically ON after time defined by this parameter. Timer is reset to zero each time the module receive OFF command regardless from where it comes (push button, associated module, controller,..). 0 - Auto ON disabled. 1 –

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_12_2 and is of type INTEGER.

Parameter 15: Automatic turning off / on seconds or milliseconds selection

NOTE: Parameter is the same for turning OFF or ON.

The following option values may be configured -:

Value Description
0 Seconds selected
1 Milliseconds selected

The manufacturer defined default value is 0 (Seconds selected).

This parameter has the configuration ID config_15_1 and is of type INTEGER.

Parameter 30: Saving the state of the relay after a power failure

Saving the state of the relay after a power failure

The following option values may be configured -:

Value Description
0 Flush 1relay module saves its state before power failure (it returns t
1 Flush 1relay module does not save the state after a power failure, it

The manufacturer defined default value is 0 (Flush 1relay module saves its state before power failure (it returns t).

This parameter has the configuration ID config_30_1 and is of type INTEGER.

Parameter 40: Power reporting in Watts on power change

0 – Reporting Disabled 1 – 100 = 1% - 100% Reporting enabled Power report is send (push) only when actual power in Watts in real time change for more than set percentage comparing to previous actual power in Watts, step is 1%. NOTE: If power chan

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 10.

This parameter has the configuration ID config_40_1 and is of type INTEGER.

Parameter 42: Power reporting in Watts on power change

Set value means time interval (0 – 32535) in seconds, when power report is send. Default value 300 (power report in Watts is send each 300s) 0 – Reporting Disabled 1 – 32535 = 1second – 32535 seconds. Reporting enabled. Power report is send with time

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 300.

This parameter has the configuration ID config_42_2 and is of type INTEGER.

Parameter 63: Output Switch selection

Set value means the type of the device that is connected to the output. The device type can be normally open (NO) or normally close (NC).

The following option values may be configured -:

Value Description
0 When system is turned off the output is 0V (NC).
1 When system is turned off the output is 230V or 24V (NO).

The manufacturer defined default value is 0 (When system is turned off the output is 0V (NC).).

This parameter has the configuration ID config_63_1 and is of type INTEGER.

Parameter 100: Enable / Disable Endpoints I2 or select Notification Type and Event

Enabling I2 means that Endpoint (I2) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. Endpoint device type selec

The following option values may be configured -:

Value Description
0 Endpoint, I2 disabled
1 Home Security; Motion Detection, unknown loc.
2 Carbon Monoxide; Carbon Monoxide detected, unknown location.
3 Carbon Dioxide; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown lo..
5 Heat Alarm; Overheat detected, unknown loc.
6 Smoke Alarm; Smoke detected, unknown loc.
9 Sensor binary.

The manufacturer defined default value is 1 (Home Security; Motion Detection, unknown loc.).

This parameter has the configuration ID config_100_1 and is of type INTEGER.

Parameter 101: Enable / Disable Endpoints I3 or select Notification Type and Event

Enabling I3 means that Endpoint (I3) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. Endpoint device type selec

The following option values may be configured -:

Value Description
0 Endpoint, I3 disabled
1 Home Security; Motion Detection, unknown loc.
2 Carbon Monoxide; Carbon Monoxide detected, unknown location.
3 Carbon Dioxide; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown lo..
5 Heat Alarm; Overheat detected, unknown loc.
6 Smoke Alarm; Smoke detected, unknown loc.
9 Sensor binary.

The manufacturer defined default value is 1 (Home Security; Motion Detection, unknown loc.).

This parameter has the configuration ID config_101_1 and is of type INTEGER.

Parameter 110: Temperature sensor offset settings

Set value is added or subtracted to actual measured value by sensor. 32536 – offset is 0.0C From 1 to 100–value from 0.1°C to 10.0°C is added to actual measured temperature. From 1001 to 1100 – value from -0.1 °C to -10.0 °C is subtracted to actual mea

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is 32536.

This parameter has the configuration ID config_110_2 and is of type INTEGER.

Parameter 120: Digital temperature sensor reporting

If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter.0 – Reporting disabled1- 127 = 0,1°C – 12,7°C, step is 0,1°C

Values in the range 0 to 127 may be set.

The manufacturer defined default value is 5.

This parameter has the configuration ID config_120_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZMNHAD supports 9 association groups.

Group 1: Lifeline

Lifeline group (reserved for communication with the main controller This group supports 1 nodes.

Group 2: Basic on/off (triggered at change of the input Q

state and reflectin

This group supports 16 nodes.

Group 3: Basic on/off (triggered at change of the input I2

state and reflecti

This group supports 16 nodes.

Group 4: Notification report (triggered at change of the input I2

state and r

This group supports 16 nodes.

Group 5: Binary Sensor (triggered at change of the input I2

state and reflect

This group supports 16 nodes.

Group 6: Basic on/off (triggered at change of the input I3

state and reflecti

This group supports 16 nodes.

Group 7: Notification report (triggered at change of the input I3

state and re

This group supports 16 nodes.

Group 8: Binary Sensor report(triggered at change of the input I3

state and r

This group supports 16 nodes.

Group 9: Multilevel Sensor report (triggered at change of temperature sensor)

This group supports 16 nodes.

Technical Information

Endpoints

Endpoint 0

| Command Class | Comment | |—————|———| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V1| | | COMMAND_CLASS_SENSOR_BINARY_V1| | | COMMAND_CLASS_METER_V3| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V3| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_POWERLEVEL_V1| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V0| |

Endpoint 1

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V1| | | COMMAND_CLASS_METER_V3| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| |

Endpoint 2

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SENSOR_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V2| | | COMMAND_CLASS_ALARM_V3| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |

Endpoint 3

| Command Class | Comment | |—————|———| | COMMAND_CLASS_BASIC_V0| | | COMMAND_CLASS_SENSOR_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SENSOR_MULTILEVEL_V7| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V2| | | COMMAND_CLASS_ALARM_V3| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |

Endpoint 4

Command Class Comment
COMMAND_CLASS_SENSOR_MULTILEVEL_V7  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2  
COMMAND_CLASS_ZWAVEPLUS_INFO_V2  
COMMAND_CLASS_ASSOCIATION_V2  
COMMAND_CLASS_VERSION_V2  
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.