The openHAB Documentation Has Moved

The documentation has moved to openhab.org/docs and openhab.org/addons.

Please use the link below to be redirected to the new version of this article, and update your bookmarks.

ZMNHVD Flush Dimmer 0-10V

This describes the Z-Wave device ZMNHVD, manufactured by Goap with the thing type UID of qubino_zmnhvd_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

The ZMNHVD supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data from other devices.

Overview

No device information is provided in the database. Consider updating the database to improve the documentation.

Channels

The following table summarises the channels available for the ZMNHVD -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Dimmer switch_dimmer DimmableLight Dimmer
Sensor (general) sensor_general   Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.

Sensor (general)

The sensor_general channel supports the Number item. This is a read only channel so will only be updated following state changes from the device.

Device Configuration

The following table provides a summary of the 24 configuration parameters available in the ZMNHVD. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Input 1 Switch Type By this parameter the user can set input based on device type (switch, potentiometer, 0-10V sensor,…)
11 Automatic turning off output after set time  
12 Automatic turning on output after set time  
21 Enable/Disable Double click function  
30 Saving the state of the device after a power failure  
52 Auto or manual selection  
53 PID value inside deadband  
54 PID deadband  
55 Integral sampling time  
56 P parameter  
57 I parameter  
58 D parameter Available config. parameters (data type is2 Byte DEC):
60 Minimum dimming value  
61 Maximum dimming value  
65 Dimming time (soft on/off)  
66 Dimming time when key pressed  
67 Ignore start level  
68 Dimming duration  
110 Temperature sensor offset settings  
120 Digital temperature sensor reporting  
140 Input I1 Sensor reporting  
141 Input I1 0-10V reporting threshold  
143 Minimum sensor range value  
144 Maximum sensor range value  
  Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 1: Input 1 Switch Type

By this parameter the user can set input based on device type (switch, potentiometer, 0-10V sensor,…)

The following option values may be configured -:

Value Description
0 mono-stable switch type (push button)
1 Bi-stable switch type
2 Potentiometer
3 Temperature sensor
4 Illumination sensor
5 General purpose sensor

The manufacturer defined default value is 0 (mono-stable switch type (push button)).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 11: Automatic turning off output after set time

Values in the range 0 to 32536 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_11_2 and is of type INTEGER.

Parameter 12: Automatic turning on output after set time

Values in the range 0 to 32535 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_12_2 and is of type INTEGER.

Parameter 21: Enable/Disable Double click function

Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_21_1 and is of type INTEGER.

Parameter 30: Saving the state of the device after a power failure

Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_30_1 and is of type INTEGER.

Parameter 52: Auto or manual selection

Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_52_1 and is of type INTEGER.

Parameter 53: PID value inside deadband

Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_53_1 and is of type INTEGER.

Parameter 54: PID deadband

Values in the range 0 to 100 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_54_1 and is of type INTEGER.

Parameter 55: Integral sampling time

Values in the range 0 to 127 may be set.

The manufacturer defined default value is 5.

This parameter has the configuration ID config_55_1 and is of type INTEGER.

Parameter 56: P parameter

Values in the range 0 to 1000 may be set.

The manufacturer defined default value is 100.

This parameter has the configuration ID config_56_2 and is of type INTEGER.

Parameter 57: I parameter

Values in the range 0 to 1000 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_57_2 and is of type INTEGER.

Parameter 58: D parameter

Available config. parameters (data type is2 Byte DEC):

Values in the range 0 to 1000 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_58_2 and is of type INTEGER.

Parameter 60: Minimum dimming value

Values in the range 1 to 98 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_60_1 and is of type INTEGER.

Parameter 61: Maximum dimming value

Values in the range 2 to 99 may be set.

The manufacturer defined default value is 99.

This parameter has the configuration ID config_61_1 and is of type INTEGER.

Parameter 65: Dimming time (soft on/off)

Values in the range 1 to 255 may be set.

The manufacturer defined default value is 100.

This parameter has the configuration ID config_65_2 and is of type INTEGER.

Parameter 66: Dimming time when key pressed

Values in the range 1 to 255 may be set.

The manufacturer defined default value is 3.

This parameter has the configuration ID config_66_1 and is of type INTEGER.

Parameter 67: Ignore start level

Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_67_1 and is of type INTEGER.

Parameter 68: Dimming duration

Values in the range 0 to 127 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_68_1 and is of type INTEGER.

Parameter 110: Temperature sensor offset settings

Values in the range 1 to 32536 may be set.

The manufacturer defined default value is 32536.

This parameter has the configuration ID config_110_2 and is of type INTEGER.

Parameter 120: Digital temperature sensor reporting

Values in the range 0 to 127 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_120_1 and is of type INTEGER.

Parameter 140: Input I1 Sensor reporting

Values in the range 0 to 140 may be set.

The manufacturer defined default value is 5.

This parameter has the configuration ID config_140_2 and is of type INTEGER.

Parameter 141: Input I1 0-10V reporting threshold

Values in the range 0 to 100 may be set.

The manufacturer defined default value is 5.

This parameter has the configuration ID config_141_1 and is of type INTEGER.

Parameter 143: Minimum sensor range value

Values in the range 0 to 20000 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_143_2 and is of type INTEGER.

Parameter 144: Maximum sensor range value

Values in the range 0 to 20000 may be set.

The manufacturer defined default value is 1000.

This parameter has the configuration ID config_144_2 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -: | Value | Description | |——–|————-| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups |

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZMNHVD supports 6 association groups.

Group 1: Lifeline

Reserved for communication with the main controller This group supports 1 nodes.

Group 2: basic on/off

triggered at change of the input I1 state and reflecting its state This group supports 16 nodes.

Group 3: start level change/stop level change

triggered at change of the input I1 state and reflecting its state) up to 16 nodes. Working only when the Parameter no. 1 is set to mono stable switch type. This group supports 16 nodes.

Group 4: multilevel set

triggered at changes of state/value of the Flush Dimmer 0-10V This group supports 16 nodes.

Group 5: multilevel sensor report

triggered at change of analogue sensor This group supports 16 nodes.

Group 6: multilevel sensor report

triggered at change of temperature sensor This group supports 16 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1  
COMMAND_CLASS_BASIC_V1  
COMMAND_CLASS_SWITCH_BINARY_V1  
COMMAND_CLASS_SWITCH_MULTILEVEL_V3  
COMMAND_CLASS_SWITCH_ALL_V1  
COMMAND_CLASS_SENSOR_MULTILEVEL_V0  
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1  
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1  
COMMAND_CLASS_ZWAVEPLUS_INFO_V1  
COMMAND_CLASS_CONFIGURATION_V1  
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1  
COMMAND_CLASS_POWERLEVEL_V1  
COMMAND_CLASS_ASSOCIATION_V1  
COMMAND_CLASS_VERSION_V1  
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V0  

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.